scholarly journals Effects of the Interface between Inorganic and Organic Components in a Bi2Te3–Polypyrrole Bulk Composite on Its Thermoelectric Performance

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3080
Author(s):  
Cham Kim ◽  
David Humberto Lopez
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Thermal Properties ◽  
Seebeck Coefficient ◽  
Power Factor ◽  
Energy Band ◽  
Phonon Scattering ◽  
Thermoelectric Performance ◽  
High Seebeck Coefficient ◽  
Fabrication Condition

We provided a method to hybridize Bi2Te3 with polypyrrole, thus forming an inorganic/organic bulk composite (Bi2Te3–polypyrrole), in which the effects of energy band junction and phonon scattering were expected to occur at the interface of the two components. Bi2Te3–polypyrrole exhibited a considerably high Seebeck coefficient compared to pristine Bi2Te3, and thus it recorded a somewhat increased power factor despite the loss in electrical conductivity caused by the organic component, polypyrrole. Bi2Te3–polypyrrole also exhibited much lower thermal conductivity than pristine Bi2Te3 because of the phonon scattering effect at the interface. We successfully brought about the decoupling phenomenon of electrical and thermal properties by devising an inorganic/organic composite and adjusting its fabrication condition, thereby optimizing its thermoelectric performance, which is considered the predominant property for n-type binary Bi2Te3 reported so far.

Thermoelectric Performance of Glass Microsphere Dispersed Bi-Sb Composites at Low Temperature

2013 ◽  
Vol 743-744 ◽  
pp. 120-125
Author(s):  
Zhen Chen ◽  
Ye Mao Han ◽  
Min Zhou ◽  
Rong Jin Huang ◽  
Yuan Zhou ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Materials ◽  
Sem Analysis ◽  
Glass Microsphere ◽  
Thermoelectric Performance ◽  
X Ray Diffraction ◽  
X Ray ◽  
Measurement Results

In the present study, the glass microsphere dispersed Bi-Sb thermoelectric materials have been fabricated through mechanical alloying followed by pressureless sintering. The phase composition and the microstructure were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis. Electrical conductivity, Seebeck coefficient and thermal conductivity were measured in the temperature range of 77~300 K. The ZT values were calculated according to the measurement results. The results showed that the electrical conductivity, Seebeck coefficient and thermal conductivity decreased by adding glass microsphere into Bi-Sb thermoelectric materials. However, the optimum ZT value of 0.24 was obtained at 260 K, which was increased 10% than that of the Bi-Sb matrix. So it is confirmed that the thermoelectric performance of Bi-Sb-based materials can be improved by adding moderate glass microspheres.

Synthesis and Thermoelectric Properties of Co4-XFeXSb12-YSnY Skutterudites

2011 ◽  
Vol 695 ◽  
pp. 65-68 ◽  
Author(s):  
Kwan Ho Park ◽  
Il Ho Kim
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Figure Of Merit ◽  
Phonon Scattering ◽  
Charge Compensation ◽  
Fe Doping ◽  
Sn Doping ◽  
Double Doping

Co4-xFexSb12-ySny skutterudites were synthesized by mechanical alloying and hot pressing, and thermoelectric properties were examined. The carrier concentration increased by doping and thereby the electrical conductivity increased compared with intrinsic CoSb3. Every specimen had a positive Seebeck coefficient. Fe doping caused a decrease in the Seebeck coefficient but it could be enhanced by Fe/Sn double doping possibly due to charge compensation. The thermal conductivity was desirably very low and this originated from ionized impurity-phonon scattering. Thermoelectric properties were improved remarkably by Fe/Sn doping, and a maximum figure of merit, ZT = 0.5 was obtained at 723 K in the Co3FeSb11.2Sn0.8 specimen.

scholarly journals Efficient interlayer charge release for high-performance layered thermoelectrics

2020 ◽  
Author(s):  
Hao Zhu ◽  
Zhou Li ◽  
Chenxi Zhao ◽  
Xingxing Li ◽  
Jinlong Yang ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Carrier Concentration ◽  
High Performance ◽  
Lattice Thermal Conductivity ◽  
Transport Barrier ◽  
High Seebeck Coefficient ◽  
Valence Bands ◽  
Increase Carrier Concentration

Abstract Many layered superlattice materials intrinsically possess large Seebeck coefficient and low lattice thermal conductivity, but poor electrical conductivity because of the interlayer transport barrier for charges, which has become a stumbling block for achieving high thermoelectric performance. Herein, taking BiCuSeO superlattice as an example, it is demonstrated that efficient interlayer charge release can increase carrier concentration, thereby activating multiple Fermi pockets through Bi/Cu dual vacancies and Pb codoping. Experimental results reveal that the extrinsic charges, which are introduced by Pb and initially trapped in the charge-reservoir [Bi2O2]2+ sublayers, are effectively released into [Cu2Se2]2− sublayers via the channels bridged by Bi/Cu dual vacancies. This efficient interlayer charge release endows dual-vacancy- and Pb-codoped BiCuSeO with increased carrier concentration and electrical conductivity. Moreover, with increasing carrier concentration, the Fermi level is pushed down, activating multiple converged valence bands, which helps to maintain a relatively high Seebeck coefficient and yield an enhanced power factor. As a result, a high ZT value of ∼1.4 is achieved at 823 K in codoped Bi0.90Pb0.06Cu0.96SeO, which is superior to that of pristine BiCuSeO and solely doped samples. The present findings provide prospective insights into the exploration of high-performance thermoelectric materials and the underlying transport physics.

scholarly journals Improving the Thermoelectric Properties of the Half-Heusler Compound VCoSb by Vanadium Vacancy

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1637 ◽  
Author(s):  
Lihong Huang ◽  
Junchen Wang ◽  
Xiaobo Mo ◽  
Xiaobo Lei ◽  
Sude Ma ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Seebeck Coefficient ◽  
Carrier Concentration ◽  
Thermoelectric Properties ◽  
Power Factor ◽  
Secondary Phase ◽  
Thermoelectric Performance ◽  
Heusler Compound

The effects of V vacancy on the thermoelectric performance of the half-Heusler compound VCoSb have been investigated in this study. A certain amount of CoSb secondary phase is generated in the VCoSb matrix when the content of V vacancy is more than 0.1 at%. According to the results, a ZT value of 0.6, together with a power factor of 29 μW cm−1 K−2 at 873 K, were achieved for the nonstoichiometric sample V0.9CoSb. This proved that moderate V vacancy could improve the thermoelectric (TE) properties of VCoSb. The noticeable improvements are mainly owing to the incremental Seebeck coefficient, which may benefit from the optimized carrier concentration. However, too much V vacancy will result in more CoSb impurity and deteriorate the TE performances of VCoSb owing to the increased thermal conductivity.

Mesoporous Thin Films: Thermoelectric Application

2012 ◽  
Vol 260-261 ◽  
pp. 34-39
Author(s):  
Min Hee Hong ◽  
Chang Sun Park ◽  
Yong June Choi ◽  
Hong Sup Lee ◽  
Hyung Ho Park
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Figure Of Merit ◽  
Thermoelectric Device ◽  
Mesoporous Titania ◽  
Titanium Tetraisopropoxide ◽  
Mesoporous Thin Films ◽  
High Seebeck Coefficient ◽  
Titania Films

The efficiency of a thermoelectric device depends on material properties through the figure of merit, Z = σS2/κ, where σ, S, and κ are electrical conductivity, Seebeck coefficient, and thermal conductivity, respectively. To maximize the thermoelectric figure of merit of a material, high electrical conductivity, high Seebeck coefficient, and low thermal conductivity are required. This work has focused on the synthesis of a mesoporous titania films for its application in thermoelectric generation. The mesoporous titania film was synthesized with titanium tetraisopropoxide. The triblock copolymer, Pluronic P-123 (EO20PO70EO20) was used as surfactant in 1-propanol. As a result, an improvement of electrical conductivity and reduced annealing with a lowering of thermal conductivity by distributions of pores were found to be effective to enhance the thermoelectric property.

scholarly journals High Thermoelectric Performance Achieved in Sb-Doped GeTe by Manipulating Carrier Concentration and Nanoscale Twin Grains

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 406
Author(s):  
Chao Li ◽  
Haili Song ◽  
Zongbei Dai ◽  
Zhenbo Zhao ◽  
Chengyan Liu ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Seebeck Coefficient ◽  
Power Factor ◽  
High Power ◽  
Hole Concentration ◽  
Thermoelectric Performance ◽  
Significant Suppression ◽  
Valence States ◽  
High Power Factor ◽  
Sb Doping

Lead-free and eco-friendly GeTe shows promising mid-temperature thermoelectric applications. However, a low Seebeck coefficient due to its intrinsically high hole concentration induced by Ge vacancies, and a relatively high thermal conductivity result in inferior thermoelectric performance in pristine GeTe. Extrinsic dopants such as Sb, Bi, and Y could play a crucial role in regulating the hole concentration of GeTe because of their different valence states as cations and high solubility in GeTe. Here we investigate the thermoelectric performance of GeTe upon Sb doping, and demonstrate a high maximum zT value up to 1.88 in Ge0.90Sb0.10Te as a result of the significant suppression in thermal conductivity while maintaining a high power factor. The maintained high power factor is due to the markable enhancement in the Seebeck coefficient, which could be attributed to the significant suppression of hole concentration and the valence band convergence upon Sb doping, while the low thermal conductivity stems from the suppression of electronic thermal conductivity due to the increase in electrical resistivity and the lowering of lattice thermal conductivity through strengthening the phonon scattering by lattice distortion, dislocations, and twin boundaries. The excellent thermoelectric performance of Ge0.90Sb0.10Te shows good reproducibility and thermal stability. This work confirms that Ge0.90Sb0.10Te is a superior thermoelectric material for practical application.

scholarly journals Effect of SrTiO3 Nanoparticles in Conductive Polymer on the Thermoelectric Performance for Efficient Thermoelectrics

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 777 ◽  
Author(s):  
Dabin Park ◽  
Hyun Ju ◽  
Jooheon Kim
Keyword(s):  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Room Temperature ◽  
Conductive Polymer ◽  
Inorganic Materials ◽  
Thermoelectric Performance ◽  
One Pot ◽  
High Seebeck Coefficient ◽  
Solvothermal Methods ◽  
Pani Matrix

We present hybrid organic inorganic materials, namely, SrTiO3/polyaniline (PANI) composites, with high thermoelectric performance; samples with various SrTiO3 contents (10, 20, 30, and 50 wt.%) were prepared. The PANI component was obtained through the polymerization of aniline monomers, followed by camphosulfonic acid-doping to enhance its electrical conductivity. SrTiO3, with a high Seebeck coefficient, was used as the N-type inorganic componenet; it was synthesized via a one-pot solvothermal methods and, then, dispersed into the conductive PANI matrix. The SrTiO3 content influenced the Seebeck coefficient and electrical conductivity of the resulting composites. The variations in the thermoelectric properties of the SrTiO3/PANI composites consequently changed their power factor; at room temperature, the highest value was ~49.6 μW·m/K2, which is 17 times larger than that of pure PANI.

Enhanced figure of merit in Mg2Si0.877Ge0.1Bi0.023/multi wall carbon nanotube nanocomposites

RSC Advances ◽  
2015 ◽  
Vol 5 (80) ◽  
pp. 65328-65336 ◽  
Author(s):  
Nader Farahi ◽  
Sagar Prabhudev ◽  
Matthieu Bugnet ◽  
Gianluigi A. Botton ◽  
Jianbao Zhao ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Power Factor ◽  
Figure Of Merit ◽  
Phonon Scattering ◽  
Thermoelectric Performance ◽  
Multi Wall Carbon Nanotubes ◽  
Energy Filtering ◽  
Multi Wall Carbon Nanotube

Adding multi wall carbon nanotubes to Mg2Si0.877Ge0.1Bi0.023 led to an increased power factor via energy filtering as well as a lowered thermal conductivity via increased phonon scattering, and thus an enhanced thermoelectric performance.

Fabrication and Thermoelectric Properties of p-Type Bi1Sb4Te7.5 Alloy Doped with Fe3O4

2006 ◽  
Vol 510-511 ◽  
pp. 1086-1089 ◽  
Author(s):  
Wang Kee Min ◽  
Chang Ho Lee ◽  
Yong Ho Park ◽  
Ik Min Park
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Mechanical Alloying ◽  
Seebeck Coefficient ◽  
Thermoelectric Properties ◽  
Power Factor ◽  
Hall Effect Measurement ◽  
Small Addition ◽  
Z Value ◽  
P Type

We investigated the effects of Fe3O4 (0~0.1 wt.%) on the thermoelectric properties of Bi1Sb4Te7.5 alloy prepared by mechanical alloying process. The Seebeck coefficient increased with Fe3O4 content, but the power factor decreased with Fe3O4 content because of the decreased electrical conductivity. The thermal conductivity decreased with Fe3O4. The carrier concentration measured by the Hall effect measurement decreased with Fe3O4. The thermal conductivity of 0.1 wt.% Fe3O4 alloy was 0.814 W/Km, 20%lower than that of Fe3O4 free alloy. As a result, the small addition of Fe3O4 improved the Z value owing to the decreased thermal conductivity by adding Fe3O4. The Z value of 0.01 wt.% Bi1Sb4Te7.5 alloy was 3.1×10-3 /K, the highest value among the prepared alloys.

MeV Si Ions Bombardment Effects on the Thermoelectric Properties of Si/Si+Ge Multi-Layer Superlttice Nanolayered Films

2010 ◽  
Vol 1267 ◽  
Author(s):  
Marcus Pugh ◽  
S. Budak ◽  
Cydale Smith ◽  
John Chacha ◽  
Kudus Ogbara ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Electrical Conductivity ◽  
Seebeck Coefficient ◽  
Thermoelectric Materials ◽  
Phonon Scattering ◽  
Ion Beam ◽  
Absolute Temperature ◽  
Inelastic Interaction ◽  
Before And After ◽  
The Cross

AbstractEffective thermoelectric materials have a low thermal conductivity and a high electrical conductivity. The performance of the thermoelectric materials and devices is shown by a dimensionless figure of merit, ZT = S2σT/K, where S is the Seebeck coefficient, σ is the electrical conductivity, T is the absolute temperature and K is the thermal conductivity. ZT can be increased by increasing S, increasing σ or decreasing K. MeV ion bombardment caused defects and disorder in the film and the grain boundaries of these nano-scale clusters increase phonon scattering and increase the chance of an inelastic interaction and phonon annihilation. We have prepared 100 alternating layers of Si/Si+Ge nanolayered superlattice films using the ion beam assisted deposition (IBAD). The 5 MeV Si ions bombardments have been performed using the AAMU Pelletron ion beam accelerator to make quantum clusters in the nanolayered superlattice films to decrease the cross plane thermal conductivity, increase the cross plane Seebeck coefficient and cross plane electrical conductivity. We have characterized the thermoelectric thin films before and after Si ion bombardments as we measured the cross-plane Seebeck coefficient, the cross-plane electrical conductivity, and the cross-plane thermal conductivity for different fluences

Sign in / Sign up

Export Citation Format

Share Document