scholarly journals The Design and Development of Recycled Concretes in a Circular Economy Using Mixed Construction and Demolition Waste

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4762
Author(s):  
Marcos Díaz González ◽  
Pablo Plaza Caballero ◽  
David Blanco Fernández ◽  
Manuel Miguel Jordán Vidal ◽  
Isabel Fuencisla Sáez del Bosque ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Raw Materials ◽  
Construction And Demolition Waste ◽  
Recycled Aggregate ◽  
Demolition Waste ◽  
Maximum Increase ◽  
Conventional Concrete ◽  
Design Elements ◽  
Mechanical Characterisation ◽  
Entrained Air

This research study analysed the effect of adding fine—fMRA (0.25% and 50%)—and coarse—cMRA (0%, 25% and 50%)—mixed recycled aggregate both individually and simultaneously in the development of sustainable recycled concretes that require a lower consumption of natural resources. For this purpose, we first conducted a physical and mechanical characterisation of the new recycled raw materials and then analysed the effect of its addition on fresh and hardened new concretes. The results highlight that the addition of fMRA and/or cMRA does not cause a loss of workability in the new concrete but does increase the amount of entrained air. Regarding compressive strength, we observed that fMRA and/or cMRA cause a maximum increase of +12.4% compared with conventional concrete. Tensile strength increases with the addition of fMRA (between 8.7% and 5.5%) and decreases with the use of either cMRA or fMRA + cMRA (between 4.6% and 7%). The addition of fMRA mitigates the adverse effect that using cMRA has on tensile strength. Regarding watertightness, all designed concretes have a structure that is impermeable to water. Lastly, the results show the feasibility of using these concretes to design elements with a characteristic strength of 25 MPa and that the optimal percentage of fMRA replacement is 25%.

scholarly journals Application of Construction and Demolition Waste in Civil Construction in the Brazilian Amazon—Case Study of the City of Rio Branco

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2247
Author(s):  
Fernando da Silva Souza ◽  
José Maria Franco de Carvalho ◽  
Gabriela Grotti Silveira ◽  
Vitória Cordeiro Araújo ◽  
Ricardo André Fiorotti Peixoto
Keyword(s):  
Mechanical Strength ◽  
Raw Materials ◽  
Amazon Region ◽  
Construction And Demolition Waste ◽  
Recycled Aggregates ◽  
Federal State ◽  
Construction Sites ◽  
Demolition Waste ◽  
Conventional Concrete ◽  
Initial Adhesion

The lack of usable aggregates for civil construction in Rio Branco (capital of Acre, a Federal State in the Amazon region) makes the production and use of recycled aggregates from construction and demolition waste (CDW) an alternative of great interest. In this study, a comprehensive characterization of CDW collected from 24 construction sites of six building types and three different construction phases (structures, masonry, and finishing) was carried out. The fine and coarse recycled aggregates were produced and evaluated in 10 different compositions. The aggregates’ performance was evaluated in four mixtures designed for laying and coating mortars with a total replacement of conventional aggregates and a mixture designed for a C25 concrete with 50% and 100% replacement of conventional aggregates. CDW mortars showed lower densities and greater water retention, initial adhesion, and mechanical strength than conventional mortars. CDW concretes presented lower densities and greater resistance to chloride penetration than conventional concrete, with a small mechanical strength reduction. The recycled CDW aggregates proved to be technologically feasible for safe application in mortars and concrete; for this reason, it is believed that the alternative and proposed methodology is of great interest to the Amazonian construction industry, considering the high costs of raw materials and the need for defining and consolidating a sustainable development model for the Amazon region.

scholarly journals Bond Behavior Between Recycled Concrete Containing CDW and Different Types of Steel Bars

2021 ◽  
Vol 4 (2) ◽  
Author(s):  
Carine N. S. Reis ◽  
Paulo R. L. Lima ◽  
Mônica B. Leite
Keyword(s):  
Recycled Concrete ◽  
Construction And Demolition Waste ◽  
Recycled Aggregate ◽  
Fine Aggregate ◽  
Demolition Waste ◽  
Conventional Concrete ◽  
Recycled Fine Aggregate ◽  
Steel Bar ◽  
Internal Forces ◽  
Steel Rebars

The operation of reinforced concrete structures is directly associated with the adhesion between the steel bar and the concrete, which allows the internal forces to be transferred to the reinforcement during the process of loading the structural elements. The modification of the concrete composition, with the introduction of recycled aggregate from construction and demolition waste (CDW), affects the steel-concrete interface and can modify the bonding stress, which is also influenced by the type and diameter of the bar used. In this work, the influence of the recycled fine aggregate (RFA) and types of steel bar on the steel-concrete bond was experimentally evaluated using the pullout test. Conventional concrete and recycled concrete, with RFA replacement level of 25%, were produced. Two types of steel rebars (i.e.,plain and deformed) with  diameters of 10.0 and 16.0mm were considered in this paper. The results indicate a reduction in the adhesion stress with the introduction of recycled aggregate, but this trend is influenced by the diameter of the bar used. The use of ribbed bars modifies the stress bon-slip behavior, with an increase in the average bond strength, which is also observed with the reduction of the diameter of the bar.

scholarly journals Construction and Demolition Waste As Recycled Aggregate for Environmentally-Friendly Concrete Paving.

2021 ◽  
Author(s):  
Manuel Contreras Llanes ◽  
Maximina Romero Pérez ◽  
Manuel Jesús Gázquez González ◽  
Juan Pedro Bolívar Raya
Keyword(s):  
Tensile Strength ◽  
Reference Sample ◽  
Production Costs ◽  
Construction And Demolition Waste ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Demolition Waste ◽  
Natural Sand ◽  
Natural Aggregates ◽  
Sand And Gravel

Abstract Recycled aggregates (RA) from construction and demolition waste (CDW) instead of natural aggregates (NA) was analysed in the manufacture of new eco-friendly concrete. Fine (FRA) and coarse (CRA) recycled aggregates were used in different percentages as substitutes of natural sand and gravel, respectively. The results revealed that the use of RA in percentages of up to 50 wt.% are feasible. Additionally, RA were used to produce paving blocks in accordance with industrial requirements. Thus, values of water absorption lesser than 6% and tensile strength upper than 3.6 MPa were obtained, which are similar to those of a reference sample. These results were achieved by reducing the incorporation of cement, thereby saving production costs and minimizing environmental impact.

scholarly journals Feasibility of Using Nanoparticles of SiO2 to Improve the Performance of Recycled Aggregate Concrete

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Khaleel H. Younis ◽  
Shelan M. Mustafa
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Splitting Tensile Strength ◽  
Recycled Aggregate Concrete ◽  
Construction And Demolition Waste ◽  
Recycled Aggregate ◽  
Demolition Waste ◽  
Aggregate Concrete ◽  
Natural Aggregate

The aim of this paper was to examine the feasibility of using nanoparticles of SiO2 (nanosilica) to improve the performance of recycled aggregate concrete (RAC) containing recycled aggregate (RA) derived from processing construction and demolition waste of concrete buildings. The examined properties include compressive strength, splitting tensile strength, and water absorption. The study also includes examining the microstructure of RA and RAC with and without nanoparticles of SiO2. In total, nine mixes were investigated. Two mixes with RA contents of 50% and 100% were investigated and for each RA content; three mixes were prepared with three different nanoparticles dosages 0.4%, 0.8%, and 1.2% (by mass of cement). A control mix with natural aggregate (NA) was also prepared for comparison reasons. The results show that nanoparticles of silica can improve the compressive strength, tensile strength, reduce the water absorption, and modify the microstructure of RAC.

scholarly journals Effect of Recycled Coarse Aggregate and Bagasse Ash on Two-Stage Concrete

Crystals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 556
Author(s):  
Muhammad Faisal Javed ◽  
Afaq Ahmad Durrani ◽  
Sardar Kashif Ur Rehman ◽  
Fahid Aslam ◽  
Hisham Alabduljabbar ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Construction Material ◽  
Strength Reduction ◽  
Recycled Aggregate ◽  
Two Stage ◽  
Conventional Concrete ◽  
Recycled Coarse Aggregate ◽  
Coarse Aggregates

Numerous research studies have been conducted to improve the weak properties of recycled aggregate as a construction material over the last few decades. In two-stage concrete (TSC), coarse aggregates are placed in formwork, and then grout is injected with high pressure to fill up the voids between the coarse aggregates. In this experimental research, TSC was made with 100% recycled coarse aggregate (RCA). Ten percent and twenty percent bagasse ash was used as a fractional substitution of cement along with the RCA. Conventional concrete with 100% natural coarse aggregate (NCA) and 100% RCA was made to determine compressive strength only. Compressive strength reduction in the TSC was 14.36% when 100% RCA was used. Tensile strength in the TSC decreased when 100% RCA was used. The increase in compressive strength was 8.47% when 20% bagasse ash was used compared to the TSC mix that had 100% RCA. The compressive strength of the TSC at 250 °C was also determined to find the reduction in strength at high temperature. Moreover, the compressive and tensile strength of the TSC that had RCA was improved by the addition of bagasse ash.

Concrete Production of Hot Asphalt Using Recycled Aggregates CDW

2016 ◽  
Vol 881 ◽  
pp. 346-350 ◽  
Author(s):  
Luzana Leite Brasileiro ◽  
Fátima Maria de Souza Pereira ◽  
Pablo de Abreu Vieira ◽  
José Milton Elias de Matos
Keyword(s):  
Solid Waste ◽  
National Policy ◽  
Mechanical Tests ◽  
Construction And Demolition Waste ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Demolition Waste ◽  
Final Destination ◽  
Natural Aggregate ◽  
Concrete Production

Every year, there is a considerable increase in the exploitation of deposits to supply the market for aggregates. On the other hand, so does the production of solid waste from construction and demolition waste (CDW). In 2010 Brazil approved the PNRS (National Policy on Solid Waste), which sets out how the country should have their waste, encouraging recycling and sustainability. As an alternative to the above problem, this paper aims to investigate the feasibility of partial and total replacement of the asphalt concrete aggregates by recycled aggregates from CDW in order to reduce the environmental impacts caused by the operation of quarries and give an adequate final destination the residue produced by man in construction. Were carried out five (05) projects mixture of: the first (parameter of our research) used only natural aggregates (0% CDW) in the second, third and fourth replaced 25%, 50% and 75% respectively of natural aggregate by the recycled aggregate and the fifth and last, used only recycled aggregates (100% CDW). They carried out the characterization of the aggregates by means of physico-chemical and mechanical, analyzing them with reference based on specific standards paving. For mixtures, they calculated the volumetric parameters and performed mechanical tests of tensile strength and stability. The results indicate that the recycled aggregate, in a defined proportion, can replace the natural aggregate in the flexible pavements

scholarly journals Effects of Recycled Aggregate Resin (RAR) in Concrete Material

2020 ◽  
Vol 11 (2) ◽  
Author(s):  
Sharifah Salwa Mohd Zuki ◽  
◽  
Shahiron Shahidan ◽  
Shivaraj Subramaniam ◽  
◽  
...  
Keyword(s):  
Epoxy Resin ◽  
Recycled Aggregate Concrete ◽  
Construction And Demolition Waste ◽  
Recycled Aggregate ◽  
Engineering Properties ◽  
Recycled Aggregates ◽  
Hardened Concrete ◽  
Demolition Waste ◽  
Split Tensile Strength ◽  
Close Proximity

This paper discussed the recycled aggregates produced from construction and demolition waste and their utilization in concrete construction. Along with a brief overview of the engineering properties of recycled aggregates, the paper also summarizes the effect and use of recycled aggregates on the properties of fresh and hardened concrete. The recycled aggregates were treated with epoxy resin to reduce the water absorptions with different percentages of resin such as 0%, 25%, 50%, 75%, and 100%. Epoxy resin is widely used in recent years owing to the enhancing of mechanical and durability of the concrete. This research also showed, recycled aggregate concrete are close proximity to normal concrete in terms of split tensile strength, compression strength and wet density. The low usage of resin was obtained good strength concrete compared to high percentage contained treated aggregates due to low bonding between material.

scholarly journals Analysis of Compressive Fatigue Failure of Recycled Aggregate Concrete

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4620
Author(s):  
Fan You ◽  
Surong Luo ◽  
Jianlan Zheng ◽  
Kaibin Lin
Keyword(s):  
Fatigue Life ◽  
Fatigue Failure ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
Recycled Aggregate Concrete ◽  
Construction And Demolition Waste ◽  
Recycled Aggregate ◽  
Cycle Fatigue ◽  
Demolition Waste ◽  
Aggregate Concrete

Using recycled aggregate in concrete is effective in recycling construction and demolition waste. It is of critical significance to understand the fatigue properties of recycled aggregate concrete (RAC) to implement it safely in structures subjected to repeated or fatigue load. In this study, a series of fatigue tests was performed to investigate the compressive fatigue behavior of RAC. The performance of interfacial transition zones (ITZs) was analyzed by nanoindentation. Moreover, the influence of ITZs on the fatigue life of RAC was discussed. The results showed that the fatigue life of RAC obeyed the Weibull distribution, and the S-N-p equation could be obtained based on the fitting of Weibull parameters. In the high cycle fatigue zone (N≥104), the fatigue life of RAC was lower than that of natural aggregate concrete (NAC) under the same stress level. The fatigue deformation of RAC presented a three-stage deformation regularity, and the maximum deformation at the point of fatigue failure closely matched the monotonic stress-strain envelope. The multiple ITZs matched the weak areas of RAC, and the negative effect of ITZs on the fatigue life of RAC in the high cycle fatigue zone was found to be greater than that of NAC.

The Properties of Fine Recycled Aggregate Concrete Containing Recycled Bricks from Construction and Demolition Waste

2018 ◽  
Vol 760 ◽  
pp. 193-198 ◽  
Author(s):  
Kristina Fořtová ◽  
Tereza Pavlů
Keyword(s):  
Recycled Aggregate Concrete ◽  
Construction And Demolition Waste ◽  
Recycled Aggregate ◽  
Partial Replacement ◽  
Fine Aggregate ◽  
Demolition Waste ◽  
Natural Sand ◽  
Aggregate Concrete ◽  
Freeze Thaw ◽  
Recycled Fine Aggregate

This paper presents research results of recycled fine aggregate concrete testing. The main aim of this contribution is verification of properties of fine aggregate concrete with partial replacement of fine natural aggregate by recycled masonry aggregate originated from construction and demolition waste. The influence of partial replacement of natural sand to mechanical properties and freeze-thaw resistance is described. The compressive strength and flexural strength were tested at the age of 28 and 60 days and after 25, 50, 75 and 100 freeze-thaw cycles. Partial replacement of natural sand was 0, 25 and 50 % for all these tests. Prismatic specimens were examined.

Sign in / Sign up

Export Citation Format

Share Document