scholarly journals Ceramic-Based Piezoelectric Material for Energy Harvesting Using Hybrid Excitation

Materials ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 5816
Author(s):  
Bartłomiej Ambrożkiewicz ◽  
Zbigniew Czyż ◽  
Paweł Karpiński ◽  
Paweł Stączek ◽  
Grzegorz Litak ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Lead Zirconate Titanate ◽  
Bluff Body ◽  
Fiber Composite ◽  
Air Flow ◽  
Linear Acceleration ◽  
Test Rig ◽  
Piezoelectric Energy

This paper analyzes the energy efficiency of a Micro Fiber Composite (MFC) piezoelectric system. It is based on a smart Lead Zirconate Titanate material that consists of a monolithic PZT (piezoelectric ceramic) wafer, which is a ceramic-based piezoelectric material. An experimental test rig consisting of a wind tunnel and a developed measurement system was used to conduct the experiment. The developed test rig allowed changing the air velocity around the tested bluff body and the frequency of forced vibrations as well as recording the output voltage signal and linear acceleration of the tested object. The mechanical vibrations and the air flow were used to find the optimal performance of the piezoelectric energy harvesting system. The performance of the proposed piezoelectric wind energy harvester was tested for the same design, but of different masses. The geometry of the hybrid bluff body is a combination of cuboid and cylindrical shapes. The results of testing five bluff bodies for a range of wind tunnel air flow velocities from 4 to 15 m/s with additional vibration excitation frequencies from 0 to 10 Hz are presented. The conducted tests revealed the areas of the highest voltage output under specific excitation conditions that enable supplying low-power sensors with harvested energy.

scholarly journals Power-Generation Optimization Based on Piezoelectric Ceramic Deformation for Energy Harvesting Application with Renewable Energy

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2171
Author(s):  
Hyeonsu Han ◽  
Junghyuk Ko
Keyword(s):  
Power Generation ◽  
Renewable Energy ◽  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Ceramic ◽  
Piezoelectric Element ◽  
Piezoelectric Ceramics ◽  
Lead Zirconate ◽  
Piezoelectric Energy

Along with the increase in renewable energy, research on energy harvesting combined with piezoelectric energy is being conducted. However, it is difficult to predict the power generation of combined harvesting because there is no data on the power generation by a single piezoelectric material. Before predicting the corresponding power generation and efficiency, it is necessary to quantify the power generation by a single piezoelectric material alone. In this study, the generated power is measured based on three parameters (size of the piezoelectric ceramic, depth of compression, and speed of compression) that contribute to the deformation of a single PZT (Lead zirconate titanate)-based piezoelectric element. The generated power was analyzed by comparing with the corresponding parameters. The analysis results are as follows: (i) considering the difference between the size of the piezoelectric ceramic and the generated power, 20 mm was the most efficient piezoelectric ceramic size, (ii) considering the case of piezoelectric ceramics sized 14 mm, the generated power continued to increase with the increase in the compression depth of the piezoelectric ceramic, and (iii) For piezoelectric ceramics of all diameters, the longer the depth of deformation, the shorter the frequency, and depending on the depth of deformation, there is a specific frequency at which the charging power is maximum. Based on the findings of this study, PZT-based elements can be applied to cases that receive indirect force, including vibration energy and wave energy. In addition, the power generation of a PZT-based element can be predicted, and efficient conditions can be set for maximum power generation.

Study of Cantilever Structures Based on Piezoelectric Materials for Energy Harvesting at Low Frequency of Vibration

2014 ◽  
Vol 976 ◽  
pp. 159-163 ◽  
Author(s):  
Roberto Ambrosio ◽  
Hector Gonzalez ◽  
Mario Moreno ◽  
Alfonso Torres ◽  
Rafael Martinez ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Power ◽  
Lead Zirconate Titanate ◽  
Maximum Output Power ◽  
Low Frequency ◽  
Electrical Contacts ◽  
Piezoelectric Energy Harvesting ◽  
Maximum Output ◽  
Coupling Coefficients ◽  
Piezoelectric Energy

In this work is presented a study of a piezoelectric energy harvesting device used for low power consumption applications operating at relative low frequency. The structure consists of a cantilever beam made by Lead Zirconate Titanate (PZT) layer with two gold electrodes for electrical contacts. The piezoelectric material was selected taking into account its high coupling coefficients. Different structures were analyzed with variations in its dimensions and shape of the cantilever. The devices were designed to operate at the resonance frequency to get maximum electrical power output. The structures were simulated using finite element (FE) software. The analysis of the harvesting devices was performed in order to investigate the influence of the geometric parameters on the output power and the natural frequency. To validate the simulation results, an experiment with a PZT cantilever with brass substrate was carried out. The experimental data was found to be very close to simulation data. The results indicate that large structures, in the order of millimeters, are the ideal for piezoelectric energy harvesting devices providing a maximum output power in the range of mW

An experimental study on piezoelectric energy harvesting from wind and ambient structural vibrations for wireless structural health monitoring

2019 ◽  
Vol 23 (5) ◽  
pp. 1010-1023 ◽  
Author(s):  
Naveet Kaur ◽  
Dasari Mahesh ◽  
Sreenitya Singamsetty
Keyword(s):  
Structural Health Monitoring ◽  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Health Monitoring ◽  
Lead Zirconate ◽  
Piezoelectric Energy Harvesting ◽  
Structural Vibrations ◽  
Ambient Wind ◽  
Piezoelectric Energy ◽  
Zirconate Titanate

Energy harvesting is an emerging technology holding promise of sustainability amid the alarming rate at which the human community is depleting the natural resources to cater its needs. There are several ways of harvesting energy in a renewable fashion such as through solar, wind, hydro-electric, geothermal, and artificial photosynthesis. This study focuses on energy harvesting from wind vibrations and ambient structural vibrations (such as from rail and road bridges) through piezo transducers using the direct piezoelectric effect. First, the potential of the piezoelectric energy harvesting from ambient wind vibrations has been investigated and presented here. Lead zirconate titanate patches have been attached at the fixed end of aluminum rectangular and trapezoidal cantilevers, which have been exposed to varying wind velocity in a lab-size wind tunnel. The effect of perforations and twisting (distortion) on the power generated by the patches under varying wind velocity has also been studied. It has been observed that the power is comparatively higher in rectangular-shaped cantilever than the trapezoidal one. Perforations and shape distortion showed promising result in terms of higher yield. The laboratory experiments have also been extended to the real-life field condition to measure the actual power generated by the lead zirconate titanate patches under the ambient wind vibrations. Next, energy harvesting from the ambient structural vibrations has been done both experimentally and numerically. Four different prototypes have been considered. The power has been measured across the lead zirconate titanate patches individually and in parallel combination. A maximum power output for Prototype 1 to Prototype 4 has been found to be 4.3428, 11.844, 25.97, and 43.12 µW, respectively. Numerical study has also been carried out in ANSYS 14.5 to perform the parametric study to examine the effect of addition of mass at the free end of cantilever. In a nutshell, this article provides a comprehensive study on the effect of various factors on the amount of energy generated by piezoelectric patches under wind and structural vibrations. The energy generated is sufficient for driving low-power-consuming electronics that can further be used for other applications like wireless structural health monitoring, and so on.

scholarly journals Performance Evaluation of a Piezoelectric Energy Harvester Based on Flag-Flutter

Micromachines ◽  
2020 ◽  
Vol 11 (10) ◽  
pp. 933 ◽  
Author(s):  
Hassan Elahi ◽  
Marco Eugeni ◽  
Federico Fune ◽  
Luca Lampani ◽  
Franco Mastroddi ◽  
...  
Keyword(s):  
Performance Evaluation ◽  
Wind Tunnel ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Research Work ◽  
Maximum Output ◽  
Operational Environment ◽  
Subsonic Wind Tunnel ◽  
Piezoelectric Energy

In the last few decades, piezoelectric (PZT) materials have played a vital role in the aerospace industry because of their energy harvesting capability. PZT energy harvesters (PEH) absorb the energy from an operational environment and can transform it into useful energy to drive nano/micro-electronic components. In this research work, a PEH based on the flag-flutter mechanism is presented. This mechanism is based on fluid-structure interaction (FSI). The flag is subjected to the axial airflow in the subsonic wind tunnel. The performance evaluation of the harvester and aeroelastic analysis is investigated numerically and experimentally. A novel solution is presented to extract energy from Limit Cycle Oscillations (LCOs) phenomenon by means of PZT transduction. The PZT patch absorbs the flow-induced structural vibrations and transforms it into electrical energy. Furthermore, the optimal resistance and length of the flag is predicted to maximize the energy harvesting. Different configurations of flag i.e., with Aluminium (Al) patch and PZT patch for flutter mode vibration mode are studied numerically and experimentally. The bifurcation diagram is constructed for the experimental campaign for the flutter instability of a cantilevered flag in subsonic wind-tunnel. Moreover, the flutter boundary conditions are analysed for reduced critical velocity and frequency. The designed PZT energy harvester via flag-flutter mechanism is suitable for energy harvesting in aerospace engineering applications to drive wireless sensors. The maximum output power that can be generated from the designed harvester is 6.72 mW and the optimal resistance is predicted to be 0.33 MΩ.

Synchronization of Cantilevers Arranged in Line of a Piezoelectric Energy Harvester

2015 ◽  
Author(s):  
Max Spornraft ◽  
Norbert Schwesinger ◽  
Shlomo Berger
Keyword(s):  
Energy Harvesting ◽  
Bluff Body ◽  
Energy Harvester ◽  
Phase Synchronization ◽  
Vibrational Excitation ◽  
Line Energy ◽  
Mechanical Coupling ◽  
Piezoelectric Energy ◽  
Piezoelectric Cantilever ◽  
The Right

Synchronization opens further ways to improve cantilever-based energy harvesting arrays in view of power output, easier rectification and scaling. Objective of this study is to investigate the synchronization behavior of a cantilever-array based energy harvesting systems. Thereby, synchronization is achieved by mechanical coupling through a so-called “overhang”. Nakajima et al. [1] and Wang et al. [2] already verified this principle for the synchronization of two and three cantilevers, but at constant vibrational excitation. Regarding energy harvesting, no application of this method is presently available. In this paper, we investigate the synchronization behavior of a piezoelectric cantilever-line energy harvester in airflow. The design of the energy harvester bases upon a piezoelectric cantilever-line and a common bluff body, arranged upstream. To investigate synchronization of the cantilevers, three commonly available piezoelectric bimorphs were employed to study synchronization. Mounted on a common bluff body, the effect of overhang material and position was studied. Therefore, different constellations were examined by impulse excitation as well as vortex-induced vibration in a wind channel. In several measurements, we found arrangements and parameters allowing for an in-phase synchronization of neighborly cantilevers of the line. The knowledge gained allows for a direct electrical connection of piezoelectric cantilevers with just one single rectifier unit. Cantilevers coupled with overhangs arranged in the right order oscillate with the same frequency and phase, i.e. without any charge cancellations. This knowledge opens ways to develop basic design rules for the synchronization of cantilevers.

Tunable Energy Harvesting From Ambient Vibrations

2010 ◽  
Author(s):  
Mohamed Rhimi ◽  
Nizar Lajnef
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Coupling Effect ◽  
Energy Levels ◽  
Axial Loading ◽  
Lead Zirconate ◽  
Energy Scavenging ◽  
Ambient Vibrations ◽  
Civil Structures ◽  
Piezoelectric Energy

Most civil structures have a low vibration response frequency range, generally one to two orders of magnitude lower than the operating frequency spectrum of most piezoelectric energy scavenging devices, which is dictated by the device’s design and the used materials. This considerably limits the levels of harvestable power under ambient vibrations. In this paper, the improvement of the energy harvesting characteristics of a bimorph cantilever lead zirconate titanate (PZT) piezoelectric beam through the application of initial pre-stress loading conditions is studied. A generalized model that can take into account all the vibration modes of the beam as well as the back coupling effect is derived using the Hamiltonian principle. The model describes the effect of the pre-stress parameters on the harvestable energy levels. Results showing the variations of the natural frequency, amplitude, and efficiency of the piezoelectric device with varying preload are presented. Vibration recordings from a bridge under ambient loading are used to show variations of the harvested power with different pre-stress conditions. Increases of up to 250% in the output power levels are shown possible through the application of 8N of compressive axial loading for a system with a 15g vibrating mass. Experimental verification of the model is also performed. The time and frequency domain responses of a piezoelectric bimorph are measured and compared to theoretical results.

scholarly journals The State-of-the-Art Brief Review on Piezoelectric Energy Harvesting from Flow-Induced Vibration

2021 ◽  
Vol 2021 ◽  
pp. 1-19
Author(s):  
Hongjun Zhu ◽  
Tao Tang ◽  
Huohai Yang ◽  
Junlei Wang ◽  
Jinze Song ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Bluff Body ◽  
Mechanical Energy ◽  
Wake Flow ◽  
Structural Vibration ◽  
Small Scale ◽  
Flow Induced Vibration ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Self Powered

Flow-induced vibration (FIV) is concerned in a broad range of engineering applications due to its resultant fatigue damage to structures. Nevertheless, such fluid-structure coupling process continuously extracts the kinetic energy from ambient fluid flow, presenting the conversion potential from the mechanical energy to electricity. As the air and water flows are widely encountered in nature, piezoelectric energy harvesters show the advantages in small-scale utilization and self-powered instruments. This paper briefly reviewed the way of energy collection by piezoelectric energy harvesters and the various measures proposed in the literature, which enhance the structural vibration response and hence improve the energy harvesting efficiency. Methods such as irregularity and alteration of cross-section of bluff body, utilization of wake flow and interference, modification and rearrangement of cantilever beams, and introduction of magnetic force are discussed. Finally, some open questions and suggestions are proposed for the future investigation of such renewable energy harvesting mode.

scholarly journals Analysis and Comparison of Macro Fiber Composites and Lead Zirconate Titanate (PZT) Discs for an Energy Harvesting Floor

2020 ◽  
Vol 10 (17) ◽  
pp. 5951
Author(s):  
Carlos Quiterio Gómez Muñoz ◽  
Gabriel Zamacola Alcalde ◽  
Fausto Pedro García Márquez
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Materials ◽  
Low Cost ◽  
Clean Energy ◽  
Lead Zirconate ◽  
Piezoelectric Transducers ◽  
Piezoelectric Energy ◽  
Pressure Cycle ◽  
Low Consumption

The main drawback in many electronic devices is the duration of their batteries. Energy harvesting provides a solution for these low-consumption devices. Piezoelectric energy harvesting use is growing because it collects small amounts of clean energy and transforms it to electricity. Synthetic piezoelectric materials are a feasible alternative to generate energy for low consumption systems. In addition to the energy generation, each pressure cycle in the piezoelectric material can provide information for the device, for example, counting the passage of people. The main contribution of this work is to study, build, and test a low-cost energy harvesting floor using piezoelectric transducers to estimate the amount of energy that could be produced for a connected device. Several piezoelectric transducers have been employed and analyzed, providing accurate results.

An enhanced hybrid piezoelectric–electromagnetic energy harvester using dual-mass system for vortex-induced vibrations

2021 ◽  
pp. 107754632110418
Author(s):  
Asan GA Muthalif ◽  
Muhammad Hafizh ◽  
Jamil Renno ◽  
Mohammad R Paurobally
Keyword(s):  
Bluff Body ◽  
Energy Harvester ◽  
Fiber Composite ◽  
Body Movement ◽  
Secondary Beam ◽  
Element Analysis ◽  
Mass System ◽  
Hybrid Energy ◽  
Piezoelectric Energy ◽  
Electromechanical Transduction

This article proposes a novel hybrid piezoelectric–electromagnetic vortex-induced vibration energy harvester from flow of water inside of a pipe. The piezoelectric energy harvester was modeled with a macro-fiber composite P2-type while the electromechanical transduction was modeled by an elastic magnet coupled to the bluff body movement. A dual-mass configuration was proposed to increase the energy harvesting efficiency. Theoretical models and the submerged natural frequencies of the hybrid energy harvesters were outlined. Computational fluid dynamics and finite element analysis with ANSYS were used to visualize the response in synchronization and output the voltage extracted from the harvesting mechanisms. The addition of a secondary system improves the amount of harvestable energy and outputs more energy than just a single system. This demonstrates the superiority of a dual-mass hybrid system. A tuned secondary beam was used for L-body configurations to make use of inline oscillations, and the secondary piezoelectric output improved for all configurations. Secondary beam tuning also improved the performance of the harvester by any amount between 21% and 52% when compared against a single-mass hybrid energy harvester. A comparative study showed that the L-vertical and vertical bluff-body-tuned was the best performing hybrid-PE energy harvester based on total voltage output.

Sign in / Sign up

Export Citation Format

Share Document