scholarly journals Analysis and Comparison of Macro Fiber Composites and Lead Zirconate Titanate (PZT) Discs for an Energy Harvesting Floor

2020 ◽  
Vol 10 (17) ◽  
pp. 5951
Author(s):  
Carlos Quiterio Gómez Muñoz ◽  
Gabriel Zamacola Alcalde ◽  
Fausto Pedro García Márquez
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Materials ◽  
Low Cost ◽  
Clean Energy ◽  
Lead Zirconate ◽  
Piezoelectric Transducers ◽  
Piezoelectric Energy ◽  
Pressure Cycle ◽  
Low Consumption

The main drawback in many electronic devices is the duration of their batteries. Energy harvesting provides a solution for these low-consumption devices. Piezoelectric energy harvesting use is growing because it collects small amounts of clean energy and transforms it to electricity. Synthetic piezoelectric materials are a feasible alternative to generate energy for low consumption systems. In addition to the energy generation, each pressure cycle in the piezoelectric material can provide information for the device, for example, counting the passage of people. The main contribution of this work is to study, build, and test a low-cost energy harvesting floor using piezoelectric transducers to estimate the amount of energy that could be produced for a connected device. Several piezoelectric transducers have been employed and analyzed, providing accurate results.

Performance of lead-free piezoelectric materials in cantilever-based energy harvesting devices

2014 ◽  
Vol 03 (02) ◽  
pp. 1450010 ◽  
Author(s):  
Anuruddh Kumar ◽  
Rajeev Kumar ◽  
Vishal S. Chauhan ◽  
Rahul Vaish
Keyword(s):  
Energy Harvesting ◽  
Power Density ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Materials ◽  
Lead Zirconate ◽  
Lead Free ◽  
Frequency Range ◽  
Mean Power ◽  
Piezoelectric Energy ◽  
Energy Harvesting Devices

Energy harvesting is one of the emerging applications of piezoelectric materials. In order to replace conventional lead-based materials with lead-free materials, it is important to evaluate their performance for such applications. In the present study, finite element method-based simulation shows mean power density produced from ( K 0.475 Na 0.475 Li 0.05)( Nb 0.92 Ta 0.05 Sb 0.03) O 3 add with 0.4 wt.% CeO 2 and 0.4 wt.% MnO 2 (KNLNTS) bimorph is 96.64% of lead zirconate titanate ( Pb [ Zr x Ti 1-x] O 3) (PZT) ceramics. Load resistance (R), length of proof mass (Lm) and thickness of host layer (th) are optimized (using genetic algorithm) for maximum power density and tuning the operating frequency range which is near to natural frequency of the structure. The lead-free piezoelectric material KNLNTS has comparable results to that of PZT for piezoelectric energy harvester in the ambient frequency range of 90 Hz to 110 Hz. Results show that KNLNTS ceramics can be potentially used in energy harvesting devices.

scholarly journals Power-Generation Optimization Based on Piezoelectric Ceramic Deformation for Energy Harvesting Application with Renewable Energy

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2171
Author(s):  
Hyeonsu Han ◽  
Junghyuk Ko
Keyword(s):  
Power Generation ◽  
Renewable Energy ◽  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Ceramic ◽  
Piezoelectric Element ◽  
Piezoelectric Ceramics ◽  
Lead Zirconate ◽  
Piezoelectric Energy

Along with the increase in renewable energy, research on energy harvesting combined with piezoelectric energy is being conducted. However, it is difficult to predict the power generation of combined harvesting because there is no data on the power generation by a single piezoelectric material. Before predicting the corresponding power generation and efficiency, it is necessary to quantify the power generation by a single piezoelectric material alone. In this study, the generated power is measured based on three parameters (size of the piezoelectric ceramic, depth of compression, and speed of compression) that contribute to the deformation of a single PZT (Lead zirconate titanate)-based piezoelectric element. The generated power was analyzed by comparing with the corresponding parameters. The analysis results are as follows: (i) considering the difference between the size of the piezoelectric ceramic and the generated power, 20 mm was the most efficient piezoelectric ceramic size, (ii) considering the case of piezoelectric ceramics sized 14 mm, the generated power continued to increase with the increase in the compression depth of the piezoelectric ceramic, and (iii) For piezoelectric ceramics of all diameters, the longer the depth of deformation, the shorter the frequency, and depending on the depth of deformation, there is a specific frequency at which the charging power is maximum. Based on the findings of this study, PZT-based elements can be applied to cases that receive indirect force, including vibration energy and wave energy. In addition, the power generation of a PZT-based element can be predicted, and efficient conditions can be set for maximum power generation.

scholarly journals SIMULATION AND ANALYSIS OF DIFFERENT PIEZOELECTRIC MATERIALS IN MEMS CANTILEVER FOR ENERGY HARVESTING

2021 ◽  
Vol 9 (1) ◽  
pp. 1321-1328
Author(s):  
Abdul Aziz Khan J , Shanmugaraja P , Kannan S
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Materials ◽  
Low Frequency ◽  
Lead Zirconate ◽  
Vital Role ◽  
Von Mises Stress ◽  
And Performance ◽  
Von Mises ◽  
Implantable Sensor

MEMS Energy Harvesting(EH) devices are excepted to grow in the upcoming years, due to the increasing aspects of MEMS EH devices in vast applications. In Recent advancements in energy harvesting (EH) technologies wireless sensor devices play a vital role to extend their lifetime readily available in natural resources. In this paper the design of MEMS Cantilever at low frequency (100Hz) with different piezoelectric materials Gallium Arsenide (GaAs), Lead Zirconate Titanate (PZT-8), Tellurium Dioxide (TeO2), Zinc oxide (ZnO) is simulated and performance with different materials are compared. The results are analyzed with various parameters such as electric potential voltage, von mises stress, displacement. The paper discusses the suitability of the piezoelectric material for MEMS fully cochlear implantable sensor application.

Energy Harvesting From Pneumatic Tires Using Piezoelectric Transducers

2008 ◽  
Author(s):  
Farbod Khameneifar ◽  
Siamak Arzanpour
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Ground Surface ◽  
Lead Zirconate ◽  
Electrical Circuit ◽  
Piezoelectric Transducers ◽  
Vehicle Speed ◽  
Mechanical Motion ◽  
The Road ◽  
Optimum Load

The concept of harvesting energy in our surrounding has recently drawn global attention. Harvesting the ambient energy of the deflected tire and convert it to electricity is discussed in this paper. An Elastic pneumatic tire deflects due to the load it carries. This deflection appears as a contact patch to the road surface. Initially, the concept of the tire deflection will be discussed. This deflection is then related to the wasted energy used for deflection. The dependency of this energy to some important parameters such as the tire air pressure, vehicle speed and tire geometry and forces are primarily discussed. To harvest the deflection energy different well established methods are exists. Due to the tire environment, piezoelectric transducers can serve as the best option. Those transducers are traditionally used to produce mechanical motion due to the applied electrical charges. This material is also capable of generating electrical charges by mechanical motion and deflections. For the tire energy harvesting application, the piezoelectric stacks can be mounted inside a tire structure such that electric charge is generated therein as the wheel assembly moves along a ground surface. For this application, lead-zirconate-titanate (PZT) is selected. The PZT inside the tire is modeled as a cantilever beam vibration in its first mode of vibration. The frequency of vibration is calculated based on the car speed, tire size, and PZT stack length. A mathematical model for this energy harvesting application is derived. Based on this model, the optimum load of the electrical circuit is also found. Finally the amount of energy harvested from tire using PZT is calculated. Although this energy is not significantly high, it will be enough to provide power for wireless sensors applications.

An experimental study on piezoelectric energy harvesting from wind and ambient structural vibrations for wireless structural health monitoring

2019 ◽  
Vol 23 (5) ◽  
pp. 1010-1023 ◽  
Author(s):  
Naveet Kaur ◽  
Dasari Mahesh ◽  
Sreenitya Singamsetty
Keyword(s):  
Structural Health Monitoring ◽  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Health Monitoring ◽  
Lead Zirconate ◽  
Piezoelectric Energy Harvesting ◽  
Structural Vibrations ◽  
Ambient Wind ◽  
Piezoelectric Energy ◽  
Zirconate Titanate

Energy harvesting is an emerging technology holding promise of sustainability amid the alarming rate at which the human community is depleting the natural resources to cater its needs. There are several ways of harvesting energy in a renewable fashion such as through solar, wind, hydro-electric, geothermal, and artificial photosynthesis. This study focuses on energy harvesting from wind vibrations and ambient structural vibrations (such as from rail and road bridges) through piezo transducers using the direct piezoelectric effect. First, the potential of the piezoelectric energy harvesting from ambient wind vibrations has been investigated and presented here. Lead zirconate titanate patches have been attached at the fixed end of aluminum rectangular and trapezoidal cantilevers, which have been exposed to varying wind velocity in a lab-size wind tunnel. The effect of perforations and twisting (distortion) on the power generated by the patches under varying wind velocity has also been studied. It has been observed that the power is comparatively higher in rectangular-shaped cantilever than the trapezoidal one. Perforations and shape distortion showed promising result in terms of higher yield. The laboratory experiments have also been extended to the real-life field condition to measure the actual power generated by the lead zirconate titanate patches under the ambient wind vibrations. Next, energy harvesting from the ambient structural vibrations has been done both experimentally and numerically. Four different prototypes have been considered. The power has been measured across the lead zirconate titanate patches individually and in parallel combination. A maximum power output for Prototype 1 to Prototype 4 has been found to be 4.3428, 11.844, 25.97, and 43.12 µW, respectively. Numerical study has also been carried out in ANSYS 14.5 to perform the parametric study to examine the effect of addition of mass at the free end of cantilever. In a nutshell, this article provides a comprehensive study on the effect of various factors on the amount of energy generated by piezoelectric patches under wind and structural vibrations. The energy generated is sufficient for driving low-power-consuming electronics that can further be used for other applications like wireless structural health monitoring, and so on.

Tunable Energy Harvesting From Ambient Vibrations

2010 ◽  
Author(s):  
Mohamed Rhimi ◽  
Nizar Lajnef
Keyword(s):  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Coupling Effect ◽  
Energy Levels ◽  
Axial Loading ◽  
Lead Zirconate ◽  
Energy Scavenging ◽  
Ambient Vibrations ◽  
Civil Structures ◽  
Piezoelectric Energy

Most civil structures have a low vibration response frequency range, generally one to two orders of magnitude lower than the operating frequency spectrum of most piezoelectric energy scavenging devices, which is dictated by the device’s design and the used materials. This considerably limits the levels of harvestable power under ambient vibrations. In this paper, the improvement of the energy harvesting characteristics of a bimorph cantilever lead zirconate titanate (PZT) piezoelectric beam through the application of initial pre-stress loading conditions is studied. A generalized model that can take into account all the vibration modes of the beam as well as the back coupling effect is derived using the Hamiltonian principle. The model describes the effect of the pre-stress parameters on the harvestable energy levels. Results showing the variations of the natural frequency, amplitude, and efficiency of the piezoelectric device with varying preload are presented. Vibration recordings from a bridge under ambient loading are used to show variations of the harvested power with different pre-stress conditions. Increases of up to 250% in the output power levels are shown possible through the application of 8N of compressive axial loading for a system with a 15g vibrating mass. Experimental verification of the model is also performed. The time and frequency domain responses of a piezoelectric bimorph are measured and compared to theoretical results.

A Piezoelectric Based Energy Harvester With Dynamic Magnification

2015 ◽  
Author(s):  
Davide Castagnetti
Keyword(s):  
Energy Harvesting ◽  
Fractal Geometry ◽  
Efficient Solution ◽  
Experimental Validation ◽  
Computational Analysis ◽  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Piezoelectric Transducers ◽  
Ambient Vibrations ◽  
Piezoelectric Energy

Energy harvesting from ambient vibrations exploiting piezoelectric materials is an efficient solution for the development of self-sustainable electronic nodes. This work presents a simple and innovative piezoelectric energy harvester, intrinsically including dynamic magnification and inspired by fractal geometry. After an initial design step, computational analysis and experimental validation show a very good frequency response with five eigenfrequencies below 100 Hz. Even if the piezoelectric transducers were put only on a symmetric half of the top surface of the structure, the energy conversion is good for all the eigenfrequencies investigated.

scholarly journals Soft and Hard Piezoelectric Ceramics for Vibration Energy Harvesting

Crystals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 907
Author(s):  
Xiaodong Yan ◽  
Mupeng Zheng ◽  
Mankang Zhu ◽  
Yudong Hou
Keyword(s):  
Power Generation ◽  
Energy Harvesting ◽  
Lead Zirconate Titanate ◽  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Lead Zirconate ◽  
Vibration Energy ◽  
Vibration Energy Harvesting ◽  
Low Frequencies ◽  
Vibration Energy Harvester

The question as to which piezoelectric composition is favorable for energy harvesting has been addressed in the past few years. However, discussion on this topic continues. In this work, an answer is provided through a feasible method which can be used in selecting piezoelectric material. The energy harvesting behavior of hard (P4 and P8) and soft (P5 and P5H) lead zirconate titanate (PZT) ceramics was investigated. The results show that the maximum piezoelectric voltage coefficient g33 and transduction coefficient d33 × g33 were obtained in P5 ceramic. Meanwhile, the power generation characteristics at low frequencies were compared by the vibration energy harvester with a cantilever beam structure. The results indicate that the energy harvester fabricated by the P5 ceramic with the maximum d33 × g33 values also demonstrated the best power generation characteristics. The results unambiguously demonstrate that the power density and energy conversion efficiency of the energy harvesting devices are dominated by the d33 × g33 value of the piezoelectric materials.

scholarly journals Dielectrophoresis Structurization of PZT/PDMS Micro-Composite for Elastronic Function: Towards Dielectric and Piezoelectric Enhancement

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4071
Author(s):  
Giulia D’Ambrogio ◽  
Omar Zahhaf ◽  
Minh-Quyen Le ◽  
Jean-Fabien Capsal ◽  
Pierre-Jean Cottinet
Keyword(s):  
Lead Zirconate Titanate ◽  
Piezoelectric Materials ◽  
Low Cost ◽  
Lead Zirconate ◽  
Production Costs ◽  
Ferroelectric Ceramics ◽  
Energy Harvesters ◽  
Preferred Direction ◽  
Flexible Material ◽  
Application Fields

Piezoelectric materials have been used for decades in the field of sensors as transducers and energy harvesters. Among these, piezoelectric composites are emerging being extremely advantageous in terms of production, costs, and versatility. However, the piezoelectric performances of a composite with randomly dispersed filler are not comparable with bulk ferroelectric ceramics and electroactive polymers. In order to achieve highly performing and low-cost materials, this work aims to develop flexible composites made of Lead zirconate titanate (PZT) filler in Polydimethylsiloxane (PDMS) matrix, with a specific internal structure called quasi-1–3 connectivity. Such a structure, comprising particles arranged in columns along a preferred direction, is performed through dielectrophoresis by applying an alternating electric field on the composite before and during the polymerization. The developed flexible material could be introduced into complex structures in various application fields, as sensors for structural monitoring.

Sign in / Sign up

Export Citation Format

Share Document