scholarly journals Application of Mathematical and Experimental Approach in Description of Sedimentation of Powder Fillers in Epoxy Resin

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7520
Author(s):  
Jakub Smoleń ◽  
Piotr Olesik ◽  
Jakub Jała ◽  
Hanna Myalska-Głowacka ◽  
Marcin Godzierz ◽  
...  
Keyword(s):  
Epoxy Resin ◽  
Colloidal Silica ◽  
Experimental Approach ◽  
Calculated Data ◽  
Experimental Results ◽  
Quantitative Metallography ◽  
Sedimentation Process ◽  
Verification Process ◽  
Good Agreement

In this paper, sedimentation inhibition attempts were examined using colloidal silica in a mathematical and experimental approach. Experimental results were validated by a two-step verification process. It was demonstrated that application of quantitative metallography and hardness measurements in three different regions of samples allows us to describe the sedimentation process using modified Stokes law. Moreover, proper application of Stokes law allows one to determine the optimal colloidal silica amount, considering characteristics of applied filler (alumina or graphite). The results of mathematical calculations have been confirmed experimentally—the experimental results show good agreement with the calculated data.

scholarly journals Temperature Distribution in InGaN-MQW LEDs under Operation

2000 ◽  
Vol 5 (S1) ◽  
pp. 647-653 ◽  
Author(s):  
Veit Schwegler ◽  
Matthias Seyboth ◽  
Sven Schad ◽  
Marcus Scherer ◽  
Cristoph Kirchner ◽  
...  
Keyword(s):  
Finite Element ◽  
Temperature Distribution ◽  
Calculated Data ◽  
Finite Element Simulations ◽  
Experimental Results ◽  
Substrate Thickness ◽  
Light Emitting ◽  
Spatially Resolved ◽  
Bond Wires ◽  
Good Agreement

The temperature distribution in InGaN-MQW light emitting diodes was examined during operation with spatially resolved micro-Raman and micro-Electroluminescence measurements. The experimental results were compared to finite element simulations. A good agreement between the different experimental and calculated data is found. Maximum operation temperatures up to 140 °C at a moderate forward currents of 30 mA are revealed by all three independent methods. Influences of substrate thickness, different substrates, and even bond-wires are shown.

Temperature Distribution in InGaN-MQW LEDs Under Operation

1999 ◽  
Vol 595 ◽  
Author(s):  
Veit Schwegler ◽  
Matthias Seyboth ◽  
Sven Schad ◽  
Marcus Scherer ◽  
Cristoph Kirchner ◽  
...  
Keyword(s):  
Finite Element ◽  
Temperature Distribution ◽  
Calculated Data ◽  
Finite Element Simulations ◽  
Experimental Results ◽  
Substrate Thickness ◽  
Light Emitting ◽  
Spatially Resolved ◽  
Bond Wires ◽  
Good Agreement

AbstractThe temperature distribution in InGaN-MQW light emitting diodes was examined during operation with spatially resolved micro-Raman and micro-Electroluminescence measurements. The experimental results were compared to finite element simulations. A good agreement between the different experimental and calculated data is found. Maximum operation temperatures up to 140 °C at a moderate forward currents of 30 mA are revealed by all three independent methods. Influences of substrate thickness, different substrates, and even bond-wires are shown.

Inducing Frictional Force to Enhance the Transient Response in Beams

2019 ◽  
Vol 22 (2) ◽  
pp. 88-93
Author(s):  
Hamed Khanger Mina ◽  
Waleed K. Al-Ashtrai
Keyword(s):  
Numerical Analysis ◽  
Transient Response ◽  
Frictional Force ◽  
Damping Ratio ◽  
Experimental Results ◽  
Damping Capacity ◽  
Tightening Force ◽  
Contact Areas ◽  
Good Agreement ◽  
Ansys Workbench

This paper studies the effect of contact areas on the transient response of mechanical structures. Precisely, it investigates replacing the ordinary beam of a structure by two beams of half the thickness, which are joined by bolts. The response of these beams is controlled by adjusting the tightening of the connecting bolts and hence changing the magnitude of the induced frictional force between the two beams which affect the beams damping capacity. A cantilever of two beams joined together by bolts has been investigated numerically and experimentally. The numerical analysis was performed using ANSYS-Workbench version 17.2. A good agreement between the numerical and experimental results has been obtained. In general, results showed that the two beams vibrate independently when the bolts were loosed and the structure stiffness is about 20 N/m and the damping ratio is about 0.008. With increasing the bolts tightening, the stiffness and the damping ratio of the structure were also increased till they reach their maximum values when the tightening force equals to 8330 N, where the structure now has stiffness equals to 88 N/m and the damping ratio is about 0.062. Beyond this force value, increasing the bolts tightening has no effect on stiffness of the structure while the damping ratio is decreased until it returned to 0.008 when the bolts tightening becomes immense and the beams behave as one beam of double thickness.

scholarly journals Early-Age Tensile Bond Characteristics of Epoxy Coatings for Underwater Applications

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 757 ◽  
Author(s):  
Kim ◽  
Hong ◽  
Han ◽  
Kim
Keyword(s):  
Bond Strength ◽  
Surface Treatment ◽  
Epoxy Resin ◽  
Coating Thickness ◽  
Experimental Results ◽  
Early Age ◽  
Curing Time ◽  
Bond Performance ◽  
Coating Type ◽  
Bond Characteristics

In this study, coating equipment for the effective underwater repair of submerged structures was developed. The tensile bond characteristics of selected epoxy resin coatings were investigated by coating the surface of a specimen using each of the four types of equipment. Using the experimental results, the tensile bond strength and the coating thickness were analyzed according to the type of equipment, coating, and curing time. The results show that the type of coating equipment used had the greatest effect on the measured bond strength and coating thickness of the selected coatings. However, the effect of coating type and curing time on the bond strength and the thickness was observed to be insignificant. Compared with the developed equipment, the surface treatment of the coating was observed to be more effective when using the pre-existing equipment, and thus the bond performance of the coating was improved compared to using the pre-existing equipment. Based on the experimental results, improvements and needs involving the equipment for further research were discussed.

PHOTOINDUCED NONLINEAR OCTUPOLAR POLARIZATION: TRANSIENT AND PERMANENT REGIMES

1996 ◽  
Vol 05 (04) ◽  
pp. 653-670 ◽  
Author(s):  
CÉLINE FIORINI ◽  
JEAN-MICHEL NUNZI ◽  
FABRICE CHARRA ◽  
IFOR D.W. SAMUEL ◽  
JOSEPH ZYSS
Keyword(s):  
Theoretical Analysis ◽  
Second Harmonic ◽  
Experimental Results ◽  
Polar Field ◽  
Rotational Spectrum ◽  
Dual Frequency ◽  
One Dimensional ◽  
Ethyl Violet ◽  
Disperse Red 1 ◽  
Good Agreement

An original poling method using purely optical means and based on a dual-frequency interference process is presented. We show that the coherent superposition of two beams at fundamental and second-harmonic frequencies results in a polar field with an irreducible rotational spectrum containing both a vector and an octupolar component. This enables the method to be applied even to molecules without a permanent dipole such as octupolar molecules. After a theoretical analysis of the process, we describe different experiments aiming at light-induced noncentrosymmetry performed respectively on one-dimensional Disperse Red 1 and octupolar Ethyl Violet molecules. Macroscopic octupolar patterning of the induced order is demonstrated in both transient and permanent regimes. Experimental results show good agreement with theory.

scholarly journals Comparison of Experimental and Numerical Transient Drop Deformation during Transition through Orifices in High-Pressure Homogenizers

2021 ◽  
Vol 5 (3) ◽  
pp. 32
Author(s):  
Benedikt Mutsch ◽  
Peter Walzel ◽  
Christian J. Kähler
Keyword(s):  
High Pressure ◽  
Visual Analysis ◽  
Imaging Technique ◽  
Extensional Flow ◽  
Droplet Breakup ◽  
Experimental Results ◽  
Drop Deformation ◽  
Droplet Deformation ◽  
Shadow Imaging ◽  
Good Agreement

The droplet deformation in dispersing units of high-pressure homogenizers (HPH) is examined experimentally and numerically. Due to the small size of common homogenizer nozzles, the visual analysis of the transient droplet generation is usually not possible. Therefore, a scaled setup was used. The droplet deformation was determined quantitatively by using a shadow imaging technique. It is shown that the influence of transient stresses on the droplets caused by laminar extensional flow upstream the orifice is highly relevant for the droplet breakup behind the nozzle. Classical approaches based on an equilibrium assumption on the other side are not adequate to explain the observed droplet distributions. Based on the experimental results, a relationship from the literature with numerical simulations adopting different models are used to determine the transient droplet deformation during transition through orifices. It is shown that numerical and experimental results are in fairly good agreement at limited settings. It can be concluded that a scaled apparatus is well suited to estimate the transient droplet formation up to the outlet of the orifice.

Experimental Study of a Tanker Ship Squat in Shallow Water

2014 ◽  
Vol 66 (2) ◽  
Author(s):  
Mohammadreza Fathi Kazerooni ◽  
Mohammad Saeed Seif
Keyword(s):  
Experimental Study ◽  
Shallow Water ◽  
Experimental Approach ◽  
Model Tests ◽  
Ship Hull ◽  
Experimental Results ◽  
Shallow Waters ◽  
Towing Tank ◽  
Ship Model

One of the phenomena restricting the tanker navigation in shallow waters is reduction of under keel clearance in the terms of sinkage and dynamic trim that is called squatting. According to the complexity of flow around ship hull, one of the best methods to predict the ship squat is experimental approach based on model tests in the towing tank. In this study model tests for tanker ship model had been held in the towing tank and squat of the model are measured and analyzed. Based on experimental results suitable formulae for prediction of these types of ship squat in fairways are obtained.

Steady-State and Dynamic Properties of the Floating-Ring Journal Bearing

1968 ◽  
Vol 90 (1) ◽  
pp. 243-253 ◽  
Author(s):  
F. K. Orcutt ◽  
C. W. Ng
Keyword(s):  
Steady State ◽  
Journal Bearing ◽  
Dynamic Properties ◽  
Calculated Data ◽  
Experimental Results ◽  
Supply Pressure ◽  
Pressure Parameter

Calculated data on steady-state and dynamic properties of the plain cylindrical floating-ring bearing with pressurized lubricant supply are given. The data are for a bearing with L/D of 1, and values of the ratio of inner to outer film clearances of 0.7 and 1.3. One value of dimensionless supply pressure parameter is covered. Experimental results are presented which verify the calculated results and which supplement them, particularly with respect to stability characteristics of the bearing.

Simulation of Sphere’s Motion Induced by Shock Waves

2012 ◽  
Vol 134 (10) ◽  
Author(s):  
Dan Igra ◽  
Ozer Igra ◽  
Lazhar Houas ◽  
Georges Jourdan
Keyword(s):  
Shock Waves ◽  
Drag Coefficient ◽  
Drag Force ◽  
Stationary Flow ◽  
Experimental Results ◽  
Experimental Findings ◽  
Sphere Drag ◽  
Simulation Scheme ◽  
Good Agreement

Simulations of experimental results appearing in Jourdan et al. (2007, “Drag Coefficient of a Sphere in a Non-Stationary Flow: New Results,”Proc. R. Soc. London, Ser. A, 463, pp. 3323–3345) regarding acceleration of a sphere by the postshock flow were conducted in order to find the contribution of the various parameters affecting the sphere drag force. Based on the good agreement found between present simulations and experimental findings, it is concluded that the proposed simulation scheme could safely be used for evaluating the sphere’s motion in the postshock flow.

Viscoelastic Deformation of PC/ABS Alloy

2007 ◽  
Vol 353-358 ◽  
pp. 1229-1232
Author(s):  
Z.N. Yin ◽  
L.F. Fan ◽  
Tie Jun Wang
Keyword(s):  
Dynamic Mechanical Analysis ◽  
Relaxation Modulus ◽  
Mechanical Analysis ◽  
Experimental Results ◽  
Viscoelastic Deformation ◽  
Dynamic Mechanical ◽  
Storage And Loss Moduli ◽  
Static Relaxation ◽  
Comparison Of The Results ◽  
Good Agreement

Dynamic Mechanical Analysis (DMA) and static relaxation tests are carried out to study the viscoelastic deformation of PC/ABS alloy with blending ratio of PC to ABS being 50/50. A modified approach is developed to calculate the relaxation modulus of PC/ABS alloy from the DMA experimental results of storage and loss moduli. Comparison of the results obtained from DMA and static relaxation tests is presented and good agreement is found.

Sign in / Sign up

Export Citation Format

Share Document