scholarly journals Nanoceramic Composites for Nuclear Radiation Attenuation

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 262
Author(s):  
Shankar A. Hallad ◽  
Nagaraj R. Banapurmath ◽  
Avinash S. Bhadrakali ◽  
Arun Y. Patil ◽  
Anand M. Hunashyal ◽  
...  
Keyword(s):  
Cross Sections ◽  
Cost Effective ◽  
Mechanical Tests ◽  
Absorption Capacity ◽  
Radiation Shielding ◽  
Nuclear Radiation ◽  
Cement Composites ◽  
Radiation Attenuation ◽  
Nano Powder ◽  
Structural Applications

The development of radiation attenuation materials with lean cross-sections is the need of the hour. However, the inherent threat of radiations accompanying these processes is of major concern. Thus, in an attempt to shield unnecessary radiations, several novel materials have been fabricated alongside the conventional materials available. Yet, there is a need for cost-effective, efficient shielding materials that have good mechanical strength and effective shielding properties. The present work investigates ceramic composite behaviors and radiation shielding capacity reinforced with lead oxide nano-powder. Developed nano-lead-based cement composites were subjected to mechanical tests to determine flexural and compressive strengths to check their suitability for structural applications. Further, the gamma attenuation test of the composites was conducted to determine their neutron absorption capacity. The addition of nano-leadoxide in the control beams was varied from 0.7 to 0.95 and 1 wt.% of the ceramic matrix. The percentage of nano-leadoxide that gives the best results in both enhanced properties and economic aspects was determined to be 0.6 wt.% of the cement.

Experimentation and Analysis on Reinforced Basalt and Carbon Fibres Composite Laminate

2018 ◽  
Vol 1148 ◽  
pp. 12-20
Author(s):  
Vemu Vara Prasad
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Carbon Fibers ◽  
Lower Cost ◽  
Mechanical Tests ◽  
Absorption Capacity ◽  
Reinforced Composites ◽  
Basalt Fibre ◽  
Structural Applications ◽  
The Matrix

— The aim of the present work is to investigate the mechanical properties and water absorption capacity of carbon and basalt fibers mixed with epoxy. At present there is demand for natural friendly products. Basalt reinforced composites developed recently and these mineral amorphous fibres are a valid alternative to carbon fibers for their lower cost and to glass fibres for their strength. The present paper describes briefly on basalt and carbon fibers (unidirectional) which are used as reinforcement material for composites. The matrix epoxy (LY556-HY 951) is taken in to account to access to influence on the evaluated parameters. In order to use reinforced composites for structural applications, it is necessary to perform a mechanical characterization. With this aim experiments like tensile strength, flexural strength, hardness and water absorptions are performed. Later the mechanical properties obtained from experiments are compared with ANSYS software results. Keywords—Carbon fibre; Basalt fibre; Uni-directional fibres; Reinforcement, Mechanical Tests, Water Absorption Tests

FERRIUM M54

Alloy Digest ◽  
2018 ◽  
Vol 67 (9) ◽  
Keyword(s):  
Fracture Toughness ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
High Resistance ◽  
High Strength ◽  
Cost Effective ◽  
High Fracture Toughness ◽  
High Fracture ◽  
Structural Applications ◽  
Resistance To Stress

Abstract Ferrium M54 was designed to create a cost-effective, ultra high-strength, high-fracture toughness material with a high resistance to stress-corrosion cracking for use in structural applications. This datasheet provides information on composition, hardness, and tensile properties as well asfatigue. Filing Code: SA-822. Producer or source: QuesTek Innovations, LLC.

WIELAND DURO TUNGSTEN

Alloy Digest ◽  
2020 ◽  
Vol 69 (10) ◽  
Keyword(s):  
Melting Point ◽  
Physical Properties ◽  
Tensile Properties ◽  
Modulus Of Elasticity ◽  
Radiation Shielding ◽  
High Melting ◽  
High Modulus ◽  
High Melting Point ◽  
Structural Applications ◽  
Very High

Abstract Wieland Duro Tungsten is unalloyed tungsten produced from pressed-and-sintered billets. The high melting point of tungsten makes it an obvious choice for structural applications exposed to very high temperatures. Tungsten is used at lower temperatures for applications that can benefit from its high density, high modulus of elasticity, or radiation shielding capability. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on machining. Filing Code: W-34. Producer or source: Wieland Duro GmbH.

scholarly journals In Silicon Monte Carlo Simulation Trials for Investigation of V2O5 Reinforcement Effect on Ternary Zinc Borate Glasses: Nuclear Radiation Shielding Dynamics

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1158
Author(s):  
Huseyin O. Tekin ◽  
Shams A. M. Issa ◽  
Gokhan Kilic ◽  
Hesham M. H. Zakaly ◽  
Mohamed M. Abuzaid ◽  
...  
Keyword(s):  
Effective Atomic Number ◽  
Mean Free Path ◽  
Radiation Shielding ◽  
Nuclear Radiation ◽  
Zinc Borate ◽  
Linear Attenuation Coefficient ◽  
Buildup Factor ◽  
Glass Composites ◽  
Mcnpx Code ◽  
Negative Effect

In the current study, promising glass composites based on vanadium pentoxide (V2O5)-doped zinc borate (ZnB) were investigated in terms of their nuclear-radiation-shielding dynamics. The mass and linear attenuation coefficient, half-value layer, mean free path, tenth-value layer, effective atomic number, exposure-buildup factor, and energy-absorption-buildup factor were deeply simulated by using MCNPX code, Phy-X PSD code, and WinXcom to study the validation of ZBV1, ZBV2, ZBV3, and ZBV4 based on (100−x)(0.6ZnO-0.4B2O3)(x)(V2O5) (x = 1, 2, 3, 4 mol%) samples against ionizing radiation. The results showed that attenuation competencies of the studied glasses slightly changed while increasing the V2O5 content from 1 mol% to 4 mol%. The domination of ZnO concentration in the composition compared to B2O3 makes ZnO substitution with V2O5 more dominant, leading to a decrease in density. Since density has a significant role in the attenuation of gamma rays, a negative effect was observed. It can be concluded that the aforementioned substitution can negatively affect the shielding competencies of studied glasses.

scholarly journals Sound-Absorbing and Thermal-Insulating Properties of Cement Composite Based on Recycled Rubber from Waste Tires

2021 ◽  
Vol 11 (6) ◽  
pp. 2725
Author(s):  
Jakub Svoboda ◽  
Tomáš Dvorský ◽  
Vojtěch Václavík ◽  
Jakub Charvát ◽  
Kateřina Máčalová ◽  
...  
Keyword(s):  
Building Materials ◽  
Absorption Capacity ◽  
Acoustic Properties ◽  
Strength Characteristics ◽  
Cement Composites ◽  
Waste Tires ◽  
Natural Aggregate ◽  
Thermal Insulating ◽  
Recycled Rubber ◽  
Insulating Properties

This article describes an experimental study aimed at investigating the potential use of recycled rubber granulate from waste tires of fractions 0/1 and 1/3 mm in cement composites as a 100% replacement for natural aggregates. The use of waste in the development and production of new building materials represents an important aspect for the sustainability and protection of the environment. This article is focused on the sound-absorbing and thermal-insulating properties of experimental cement composites based on recycled rubber from waste tires. The article describes the grain characteristics of recycled rubber, sound absorption capacity, thermal conductivity and strength characteristics. The results of this research show that the total replacement of natural aggregate with recycled rubber in cement composites is possible. Replacing natural aggregate with recycled rubber has significantly improved the thermal and acoustic properties of the prepared cement composites, however, at the same time; there was also the expected decrease in the strength characteristics due to the elasticity of rubber.

Ultrasonic Cavitation Based Processing of Metal Matrix Nanocomposites: An Overview

2014 ◽  
Vol 1042 ◽  
pp. 58-64 ◽  
Author(s):  
Santanu Sardar ◽  
Santanu Kumar Karmakar ◽  
Debdulal Das
Keyword(s):  
Mass Production ◽  
Metal Matrix ◽  
Cost Effective ◽  
Ultrasonic Cavitation ◽  
Basic Principles ◽  
Metal Matrix Nanocomposites ◽  
Microstructural Parameters ◽  
Structural Applications ◽  
Critical Issues ◽  
Matrix Nanocomposites

Metal matrix nanocomposites (MMNCs) have emerged as an important class of materials for structural applications specifically in the automobile and aerospace sectors; however, development of cost effective mass production technique of MMNCs with requisite operational and geometrical flexibilities is still a great challenge. Focused research in the last decade has highlighted that ultrasonic cavitation based processing is the most promising method for manufacturing of MMNCs with nearly uniform distribution of nanoparticles, having added advantage of being a liquid-phase route. This article presents an overview on the basic principles and recent advances in the ultrasonic cavitation based processing of MMNCs with a particular emphasis on identifying relationships amongst processing variables, microstructural parameters and mechanical properties. Critical issues of MMNCs fabrication are discussed.

Numerical Investigation of Cross-Section on Aluminum A6063 Thin-Walled Structures under Low-Velocity Impact Loading

2014 ◽  
Vol 1019 ◽  
pp. 96-102
Author(s):  
Ali Taherkhani ◽  
Ali Alavi Nia
Keyword(s):  
Energy Absorption ◽  
Cross Section ◽  
Cross Sections ◽  
Peak Load ◽  
Circular Cross Section ◽  
Absorption Capacity ◽  
Energy Absorption Capacity ◽  
Thin Walled Structures ◽  
Thin Walled ◽  
Crush Strength

In this study, the energy absorption capacity and crush strength of cylindrical thin-walled structures is investigated using nonlinear Finite Elements code LS-DYNA. For the thin-walled structure, Aluminum A6063 is used and its behaviour is modeled using power-law equation. In order to better investigate the performance of tubes, the simulation was also carried out on structures with other types of cross-sections such as triangle, square, rectangle, and hexagonal, and their results, namely, energy absorption, crush strength, peak load, and the displacement at the end of tubes was compared to each other. It was seen that the circular cross-section has the highest energy absorption capacity and crush strength, while they are the lowest for the triangular cross-section. It was concluded that increasing the number of sides increases the energy absorption capacity and the crush strength. On the other hand, by comparing the results between the square and rectangular cross-sections, it can be found out that eliminating the symmetry of the cross-section decreases the energy absorption capacity and the crush strength. The crush behaviour of the structure was also studied by changing the mass and the velocity of the striker, simultaneously while its total kinetic energy is kept constant. It was seen that the energy absorption of the structure is more sensitive to the striker velocity than its mass.

Sign in / Sign up

Export Citation Format

Share Document