scholarly journals Microstructure and Mechanical Properties of Novel Lightweight TaNbVTi-Based Refractory High Entropy Alloys

Materials ◽  
2022 ◽  
Vol 15 (1) ◽  
pp. 355
Author(s):  
Ao Fu ◽  
Yuankui Cao ◽  
Yuxi Liu ◽  
Shenghang Xu
Keyword(s):  
Yield Strength ◽  
Volume Fraction ◽  
High Volume ◽  
Specific Yield ◽  
Compressive Yield Strength ◽  
High Entropy Alloys ◽  
High Entropy ◽  
Solid Solution Strengthening ◽  
Plasma Sintering ◽  
Spark Plasma

A series of novel lightweight TaNbVTi-based refractory high entropy alloys (RHEA) were fabricated through ball-milling and spark plasma sintering (SPS). The reinforced phase of TiO precipitates were in-situ formed due to the introduction of Al2O3 ceramic particles. The RHEA with 15% Al2O3 exhibits a high compressive yield strength (1837 MPa) and a low density (7.75 g/cm3) with an adequate ductility retention. The yield strength and density are 32% higher and 15% lower, respectively, compared to the RHEA without Al2O3 addition. The specific yield strength (237 MPa cm3/g) of the RHEAs is much higher than that of other reported RHEAs, and is mainly ascribed to the introduction of high volume fraction of Al2O3 additives, resulting in solid solution strengthening and precipitation strengthening. Meanwhile, the ductile matrix is responsible for the good compressive plasticity.

Compression stress strengthening modelling of a ultrafine-grained equiatomic SPS CoCrFeNiNb high-entropy alloy

2020 ◽  
pp. 095440622094324
Author(s):  
Marcello Cabibbo ◽  
Filip Průša ◽  
Alexandra Šenková ◽  
Andrea Školáková ◽  
Vojtěch Kučera ◽  
...  
Keyword(s):  
Powder Metallurgy ◽  
Mechanical Alloying ◽  
Oxide Phase ◽  
High Entropy Alloy ◽  
Induction Melting ◽  
High Entropy Alloys ◽  
High Entropy ◽  
Plasma Sintering ◽  
Transmission Electron ◽  
Spark Plasma

High-entropy alloys are known to show exceptionally high mechanical properties, both compression and tensile strength, and unique physical properties, such as their phase stability. These quite unusual properties are primarily due to the microstructure generated by mechanical alloying processes, such as conventional induction arc melting, powder metallurgy, or mechanical alloying. In the present study, an equiatomic CoCrFeNiNb high-entropy alloy was prepared by a sequence of conventional induction melting, powder metallurgy, and compaction via spark plasma sintering. The high-entropy alloys showed uniform sub-micrometer grain microstructure consisted by a mixture of an fcc solid solution strengthened by a hcp Laves phase and a third intergranular oxide phase. The as-cast high-entropy alloys showed an ultimate compression strength (UCS) of ∼1400 MPa, which after sintering and compaction at 1273 K increased up to ∼2400 MPa. Extensive transmission electron microscopy quantitative analyses were carried out to model the UCS. A quite good agreement between the microstructure-strengthening model and the experimental UCS was found.

Grain growth kinetics in CoCrFeNi and CoCrFeMnNi high entropy alloys processed by spark plasma sintering

2019 ◽  
Vol 791 ◽  
pp. 1114-1121 ◽  
Author(s):  
M. Vaidya ◽  
Ameey Anupam ◽  
J. Vijay Bharadwaj ◽  
Chandan Srivastava ◽  
B.S. Murty
Keyword(s):  
Grain Growth ◽  
Spark Plasma Sintering ◽  
Growth Kinetics ◽  
High Entropy Alloys ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Grain Growth Kinetics

scholarly journals Designing (Ultra)Fine-Grained High-Entropy Alloys by Spark Plasma Sintering and Equal-Channel Angular Pressing

Crystals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1157
Author(s):  
Lisa-Marie Rymer ◽  
Thomas Lindner ◽  
Philipp Frint ◽  
Martin Löbel ◽  
Thomas Lampke
Keyword(s):  
Tensile Strength ◽  
Grain Refinement ◽  
Spark Plasma Sintering ◽  
Equal Channel Angular Pressing ◽  
High Entropy Alloys ◽  
High Entropy ◽  
Fine Grained ◽  
Angular Pressing ◽  
Plasma Sintering ◽  
Spark Plasma

Single-phase, face-centered cubic (FCC) high-entropy alloys (HEA) are promising materials for future applications. In order to improve the mechanical properties, especially the tensile strength of these materials, this study focuses on the combination of spark plasma sintering (SPS) and equal-channel angular pressing (ECAP). The initial fine-grained microstructure produced by SPS is further refined by ECAP in a 90°-die. Optical microscopy and electron backscatter diffraction (EBSD) confirm this considerable grain refinement, leads to a grain size below 1 µm after 1 ECAP pass. An alternating arrangement of fine-grained areas and much coarser regions, aligned under an angle of approximately 27°, is found. Moreover, a first microstructural investigation of the twin structure is conducted. The mechanical behavior was investigated by hardness measurements and tensile testing. Both the hardness and tensile strength are remarkably increased after ECAP. In contrast, the uniform elongation and elongation at fracture are significantly reduced due to the strengthening mechanisms of strain hardening and grain refinement. It is concluded that the combination of SPS and ECAP is an attractive approach for designing (ultra)fine-grained HEAs with superior properties. The investigated techniques could be applied to understand the underlying microstructural mechanisms.

Spark Plasma Sintering and Strength Behavior under Compressive Loading of Mg-PSZ/Al2O3-TRIP-Steel Composites

2015 ◽  
Vol 825-826 ◽  
pp. 182-188 ◽  
Author(s):  
Lutz Krüger ◽  
Steffen Grützner ◽  
Sabine Decker ◽  
Ines Schneider
Keyword(s):  
Strain Rate ◽  
Spark Plasma Sintering ◽  
Trip Steel ◽  
Volume Fraction ◽  
Compressive Yield Strength ◽  
Strain Rates ◽  
Steel Matrix ◽  
Trip Effect ◽  
Plasma Sintering ◽  
Spark Plasma

Composite materials, which consist of a metastable austenitic TRIP-steel matrix (CrMnNi TRIPsteel; TRansformation Induced Plasticity) reinforced by alumina particles (25 vol.% ceramic, designated as AT 25/75) and reinforced by alumina and MgO partially stabilized zirconia particles (Mg-PSZ) (35 vol.% ceramic, designated as AT 25/75 + MgPSZ) were synthesized through spark plasma sintering (SPS). In the AT 25/75 + MgPSZ, the steel particles were mainly surrounded by alumina. Hence, mostly steel/alumina and alumina/MgPSZ interfaces existed. The mechanical behavior of the as-sintered samples was characterized by compression tests at room temperature and 40 °C and in a range of strain rates between 103s-1and 103s1. The influence of the ceramic content, strain rate and temperature on TRIP-effect of the steel matrix was investigated. Due to the increasing ceramic volume fraction, AT 25/75 + MgPSZ exhibits the highest compressive yield strength under all loading conditions and no strain rate sensitivity. This composite showed no measurable TRIP-effect, due to the low fracture strain. The deformation-induced α’martensite within the steel particles in pure steel and AT 25/75 primary depends on the testing temperature and the strain rate. This is attributed to an increase of stacking fault energy with rising temperature. High strain rates cause adiabatic heating, counteracting the martensitic transformation.

Fabrication by SPS and Thermophysical Properties of High Volume Fraction SiCp/Al Matrix Composites

2006 ◽  
Vol 313 ◽  
pp. 171-176 ◽  
Author(s):  
X.F. Gu ◽  
Lian Meng Zhang ◽  
Mei Jun Yang ◽  
Dong Ming Zhang
Keyword(s):  
Thermophysical Properties ◽  
Volume Fraction ◽  
Coefficient Of Thermal Expansion ◽  
High Volume ◽  
High Volume Fraction ◽  
Matrix Composites ◽  
Sic Particles ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Al Matrix Composites

SiCp/Al composites containing high volume fraction of SiC particles were fabricated by spark plasma sintering (SPS), and their thermophysical properties, such as thermal conductivity (TC) and coefficient of thermal expansion (CTE), were characterized. High relative density (R-D) of composites was successfully achieved through the optimization of sintering parameters, such as sintering temperature, sintering pressure and heating rate. The measured TCs of SiCp/Al composites fabricated by SPS are higher than 195W/m.k, no matter the volume fraction of SiC particles is high or low as long as the R-D is higher than 95%. The measured CTEs of SiCp/Al composites are in good agreement with the estimated values based on Kerner,s model. The high volume fraction of SiCp/Al composites are a good candidate material to substitute for conventional thermal management materials in advanced electronic packages due to its tailorable thermophysical properties.

Sign in / Sign up

Export Citation Format

Share Document