scholarly journals In Situ Characterization of the Effect of Twin-Microstructure Interactions on {1 0 1 2} Tension and {1 0 1 1} Contraction Twin Nucleation, Growth and Damage in Magnesium

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1403
Author(s):  
William D. Russell ◽  
Nicholas R. Bratton ◽  
YubRaj Paudel ◽  
Robert D. Moser ◽  
Zackery B. McClelland ◽  
...  
Keyword(s):  
Electron Backscatter Diffraction ◽  
Tensile Loading ◽  
Major Effect ◽  
Nucleation Behavior ◽  
The Difference ◽  
Backscatter Diffraction ◽  
Critical Resolved Shear Stress ◽  
Track Deformation

Through in situ electron backscatter diffraction (EBSD) experiments, this paper uncovers dominant damage mechanisms in traditional magnesium alloys exhibiting deformation twinning. The findings emphasize the level of deleterious strain incompatibility induced by twin interaction with other deformation modes and microstructural defects. A double fiber obtained by plane-strain extrusion as a starting texture of AM30 magnesium alloy offered the opportunity to track deformation by EBSD in neighboring grains where some undergo profuse {1 0 1 2} twinning and others do not. For a tensile loading applied along extrusion transverse (ET) direction, those experiencing profuse twinning reveal a major effect of grain boundaries on non-Schmid behavior affecting twin variant selection and growth. Similarly, a neighboring grain, with its ⟨c⟩-axis oriented nearly perpendicular to tensile loading, showed an abnormally early nucleation of {1 0 1 1} contraction twins (2% strain) while the same {1 0 1 1} twin mode triggering under ⟨c⟩-axis uniaxial compression have higher value of critical resolved shear stress exceeding the values for pyramidal ⟨c + a⟩ dislocations. The difference in nucleation behavior of contraction vs. compression {1 0 1 1} twins is attributed to the hydrostatic stresses that promote the required atomic shuffles at the core of twinning disconnections.

Roping Phenomena in Aluminium Alloy 6016: A Microtextural Investigation

2010 ◽  
Vol 638-642 ◽  
pp. 396-400 ◽  
Author(s):  
Tricia A. Bennett ◽  
Jurij J. Sidor ◽  
Roumen H. Petrov ◽  
Leo Kestens
Keyword(s):  
Aluminium Alloys ◽  
Grain Orientation ◽  
Electron Backscatter Diffraction ◽  
Spatial Distributions ◽  
Process Characterization ◽  
Electron Backscatter ◽  
The Difference ◽  
Backscatter Diffraction ◽  
Different Levels

Roping was investigated in two 6016 aluminium alloys that exhibit different levels of susceptibility to its occurrence. The level of roping is lower, as manifested by the less pronounced (roping) lines on the surface, in the GR material compared to the BR case. Through-process characterization of GR and BR materials by means of electron backscatter diffraction (EBSD) reveals similarities in the grain size, (grain) orientation texture and the spatial distribution of {100} <001> Cube grains up to, but not including the T4 state. Cube grains in the T4 state are spatially banded in the BR material but more uniformly distributed in the GR case. It was found that the thermo-mechanical treatments prior to the T4 state account for the difference in spatial distributions of Cube grains and hence, the different roping behaviours exhibited by these materials.

Application of Electron Backscatter Diffraction for Crystallographic Characterization of Tin Whiskers

2012 ◽  
Vol 18 (4) ◽  
pp. 876-884 ◽  
Author(s):  
Joseph R. Michael ◽  
Bonnie B. McKenzie ◽  
Donald F. Susan
Keyword(s):  
Electron Backscatter Diffraction ◽  
Growth Direction ◽  
Tin Whiskers ◽  
Physical Growth ◽  
Final Choice ◽  
Advantages And Disadvantages ◽  
Electron Backscatter ◽  
Backscatter Diffraction

AbstractUnderstanding the growth of whiskers or high aspect ratio features on substrates can be aided when the crystallography of the feature is known. This study has evaluated three methods that utilize electron backscatter diffraction (EBSD) for the determination of the crystallographic growth direction of an individual whisker. EBSD has traditionally been a technique applied to planar, polished samples, and thus the use of EBSD for out-of-surface features is somewhat more difficult and requires additional steps. One of the methods requires the whiskers to be removed from the substrate resulting in the loss of valuable physical growth relationships between the whisker and the substrate. The other two techniques do not suffer this disadvantage and provide the physical growth information as well as the crystallographic growth directions. The final choice of method depends on the information required. The accuracy and the advantages and disadvantages of each method are discussed.

scholarly journals Application of Electron Backscatter Diffraction (EBSD) for Crystallographic Characterization of Aluminum-Doped Zinc Oxide Sputtered Films

2013 ◽  
Vol 19 (S4) ◽  
pp. 103-104
Author(s):  
C.B. Garcia ◽  
E. Ariza ◽  
C.J. Tavares
Keyword(s):  
Electron Microscopy ◽  
Grain Size ◽  
Zinc Oxide ◽  
Electron Backscatter Diffraction ◽  
Wide Range ◽  
Electron Backscatter ◽  
Aluminum Doped Zinc Oxide ◽  
Ebsd Technique ◽  
Backscatter Diffraction

Zinc Oxide is a wide band-gap compound semiconductor that has been used in optoelectronic and photovoltaic applications due to its good electrical and optical properties. Aluminium has been an efficient n-type dopant for ZnO to produce low resistivity films and high transparency to visible light. In addition, the improvement of these properties also depends on the morphology, crystalline structure and deposition parameters. In this work, ZnO:Al films were produced by d.c. pulsed magnetron sputtering deposition from a ZnO ceramic target (2.0 wt% Al2O3) on glass substrates, at a temperature of 250 ºC.The crystallographic orientation of aluminum doped zinc oxide (ZnO:Al) thin films has been studied by Electron Backscatter Diffraction (EBSD) technique. EBSD coupled with Scanning Electron Microscopy (SEM) is a powerful tool for the microstructural and crystallographic characterization of a wide range of materials.The investigation by EBSD technique of such films presents some challenges since this analysis requires a flat and smooth surface. This is a necessary condition to avoid any shadow effects during the experiments performed with high tilting conditions (70º). This is also essential to ensure a good control of the three dimensional projection of the crystalline axes on the geometrical references related to the sample.Crystalline texture is described by the inverse pole figure (IPF) maps (Figure 1). Through EBSD analysis it was observed that the external surface of the film presents a strong texture on the basal plane orientation (grains highlighted in red colour). Furthermore it was possible to verify that the grain size strongly depends on the deposition time (Figure 1 (a) and (b)). The electrical and optical film properties improve with increasing of the grain size, which can be mainly, attributed to the decrease in scattering grain boundaries which leads to an increasing in carrier mobility (Figure 2).The authors kindly acknowledge the financial support from the Portuguese Foundation for Science and Technology (FCT) scientific program for the National Network of Electron Microscopy (RNME) EDE/1511/RME/2005.

Grain Growth in Al: First Results from a Combined Study of Bulk and In-Situ Experiments Using a Columnar Structured Al Foil

2004 ◽  
Vol 467-470 ◽  
pp. 935-940 ◽  
Author(s):  
Sandra Piazolo ◽  
Vera G. Sursaeva ◽  
David J. Prior
Keyword(s):  
Grain Boundary ◽  
Grain Growth ◽  
Electron Backscatter Diffraction ◽  
Boundary Energy ◽  
Complete Replacement ◽  
Von Neumann ◽  
In Situ Experiments ◽  
First Results ◽  
Backscatter Diffraction

First results from grain growth experiments in a columnar structured Al foil show several interesting features: (a) the grain size distribution remains heterogeneous even after up to 300 min. annealing and (b) the Von Neumann-Mullins relation is not always satisfied. To clarify the underlying reasons for these features, in-situ heating experiments within a Scanning Electron Microscope (SEM) were combined with detailed Electron Backscatter Diffraction (EBSD) analysis. These show that the movement of boundaries can be strongly heterogeneous. For example, the complete replacement of one grain by a neighbouring grain without significant change of the surrounding grain boundary topology is frequently seen. Experiments show that grain boundary energy and/or mobility are anisotropic both with respect to misorientation and orientation of grain boundary plane. Low energy and/or mobility boundaries are commonly low angle boundaries, twin boundaries and boundaries that form traces to a low index plane of at least one of the adjacent grains. As a consequence the Von Neumann-Mullins relation is not always satisfied.

scholarly journals Characterization of Coarse-Grained Heat-Affected Zones in Al and Ti-Deoxidized Offshore Steels

Metals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 1096
Author(s):  
Henri Tervo ◽  
Antti Kaijalainen ◽  
Vahid Javaheri ◽  
Satish Kolli ◽  
Tuomas Alatarvas ◽  
...  
Keyword(s):  
Prior Austenite ◽  
Electron Backscatter Diffraction ◽  
Coarse Grained ◽  
Grain Coarsening ◽  
Austenite Grain ◽  
The Matrix ◽  
Backscatter Diffraction ◽  
Prior Austenite Grain ◽  
Deoxidation Practice

Deterioration of the toughness in heat-affected zones (HAZs) due to the thermal cycles caused by welding is a known problem in offshore steels. Acicular ferrite (AF) in the HAZ is generally considered beneficial regarding the toughness. Three experimental steels were studied in order to find optimal conditions for the AF formation in the coarse-grained heat-affected zone (CGHAZ). One of the steels was Al-deoxidized, while the other two were Ti-deoxidized. The main focus was to distinguish whether the deoxidation practice affected the AF formation in the simulated CGHAZ. First, two different peak temperatures and prolonged annealing were used to study the prior austenite grain coarsening. Then, the effect of welding heat input was studied by applying three cooling times from 800 °C to 500 °C in a Gleeble thermomechanical simulator. The materials were characterized using electron microscopy, energy-dispersive X-ray spectrometry, and electron backscatter diffraction. The Mn depletion along the matrix-particle interface was modelled and measured. It was found that AF formed in the simulated CGHAZ of one of the Ti-deoxidized steels and its fraction increased with increasing cooling time. In this steel, the inclusions consisted mainly of small (1–4 μm) TiOx-MnS, and the tendency for prior austenite grain coarsening was the highest.

Use of Electron Backscatter Diffraction Technique in Characterization of 6XXX Aluminum Alloy Extrusions

2000 ◽  
Vol 6 (S2) ◽  
pp. 954-955
Author(s):  
Steven R. Claves ◽  
Wojciech Z. Misiolek ◽  
William H. Van Geertruyden ◽  
David B. Williams
Keyword(s):  
Electron Backscatter Diffraction ◽  
Metal Flow ◽  
Extrusion Process ◽  
Cross Sectional ◽  
Electron Backscattering Diffraction ◽  
Electron Backscatter ◽  
Individual Grains ◽  
Backscatter Diffraction ◽  
6Xxx Series

Electron Backscattering Diffraction (EBSD) is an important tool for analyzing the crystal grain orientation of a microstructure and can be used to formulate conclusions about microtexture, texture determined from individual grains. This technique has been used to study a 6xxx series aluminum alloy's response to the deformation of the extrusion process. Extrusion is the process by which a billet of material is forced, under high pressure, through a die. The material undergoes a significant decrease in cross sectional area, and is formed into a shape equivalent to the geometry of the die orifice. Different bearing lands are shown in shown in Figure 1. These surfaces form the part, and are designed to control the metal flow making it uniform through the die, thus yielding good mechanical properties. This research was focused on the resultant microstructure. The shaded regions of Figure 2 show the two surface regions where EBSD measurements were taken.

scholarly journals Novel −75°C SEM cooling stage: application for martensitic transformation in steel

Microscopy ◽  
2020 ◽  
Author(s):  
Kaneaki Tsuzazki ◽  
Motomichi Koyama ◽  
Ryosuke Sasaki ◽  
Keiichiro Nakafuji ◽  
Kazushi Oie ◽  
...  
Keyword(s):  
Martensitic Transformation ◽  
Electron Backscatter Diffraction ◽  
Dislocation Slip ◽  
In Situ Observation ◽  
Contrast Imaging ◽  
Cooling Stage ◽  
Electron Channelling ◽  
Electron Backscatter ◽  
Backscatter Diffraction

Abstract Microstructural changes during the martensitic transformation from face-centred cubic (FCC) to body-centred cubic (BCC) in an Fe-31Ni alloy were observed by scanning electron microscopy (SEM) with a newly developed Peltier stage available at temperatures to  −75°C. Electron channelling contrast imaging (ECCI) was utilized for the in situ observation during cooling. Electron backscatter diffraction analysis at ambient temperature (20°C) after the transformation was performed for the crystallographic characterization. A uniform dislocation slip in the FCC matrix associated with the transformation was detected at −57°C. Gradual growth of a BCC martensite was recognized upon cooling from −57°C to −63°C.

Sign in / Sign up

Export Citation Format

Share Document