scholarly journals Effect of Welding Sequence and the Transverse Geometry of the Weld Overlay on the Distribution of Residual Stress in the Weld Overlay Repair of T23 Tubes

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 568
Author(s):  
Xin Xiao ◽  
Qu Liu ◽  
Mengjia Hu ◽  
Kejian Li ◽  
Zhipeng Cai
Keyword(s):  
Residual Stress ◽  
Compressive Stress ◽  
Power Plants ◽  
Residual Stress Distribution ◽  
Welding Residual Stress ◽  
Upward Movement ◽  
Weld Overlay ◽  
Transverse Geometry ◽  
Welding Sequence ◽  
Better Than

Water-wall tubes are important components in power plants and are used to absorb the heat from the boilers, and they often fail prematurely due to corrosion, erosion, and fatigue during service. To repair the defects, weld overlay repair is often adopted by forming a compressive stress area around the susceptible area to prevent the cracks from propagating. In order to obtain reasonable process parameters of weld overlay repair, a study combining experiments and numerical simulations was performed to investigate the welding residual stress distribution on the repaired area with different welding repair methods. The results reveal that a compressive stress area is generated on the repaired area after the repair, and a center-to-outside welding sequence is better than either a right-to-left welding sequence or an outside-to-center welding sequence when overlaying a one-layer weld; with an increase in the number of weld layers, the compressive stress area of the repaired area is expanded, and the stress level is increased, which results from the upward movement of the compressive stress area of the subsequent-overlaying layer and the superposition of the compression areas of the subsequent-overlaying layer and previous-overlaying layer, respectively. In addition, the number of the weld passes of each layer should be not less than four with the center-to-outside welding sequence.

scholarly journals Influence of Interlayer Temperature and Welding Sequence on the Temperature Distribution and Welding Residual Stress of the Saddle-Shaped Joint of Weldolet-Header Butt Welding

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 5980
Author(s):  
Chunliang Mai ◽  
Xue Hu ◽  
Lixin Zhang ◽  
Bao Song ◽  
Xiongfei Zheng
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Stress Distribution ◽  
High Stress ◽  
Welding Process ◽  
Residual Stress Distribution ◽  
Welding Residual Stress ◽  
Two Stage ◽  
Welding Sequence ◽  
Simulation Results

In this paper, based on Simufact Welding finite element analysis software, a numerical simulation of the temperature and residual stress distribution of the weldolet-header multi-layer multi-pass welding process is carried out, and the simulation results are verified through experiments. The experimental results are in good agreement with the numerical simulation results, which proves the validity of the numerical simulation results. Through the results of the numerical simulation, the influence of the welding sequence and interlayer temperature on the temperature and residual stress distribution at different locations of the saddle-shaped weld was studied. The results show that the temperature and residual stress distribution on the header and weldolet are asymmetric, and the high-stress area of the saddle-shaped welded joint always appears at the saddle shoulder or saddle belly position. When the interlayer temperature is 300 °C, the peak residual stress reaches a minimum of 428.35 MPa. Adjusting the welding sequence can change the distribution trend of residual stress. There is no high-stress area on the first welding side of the two-stage welding path-2. The peak values of residual stresses for continuous welding path-1 and two-stage welding path-2 are 428.35 MPa and 434.01 MPa, respectively, which are very close to each other.

Finite Element Analyses of Residual Stresses in Typical Welded Joints Used in Nuclear Power Plants and Comparisons With Experiments

2010 ◽  
Author(s):  
Dean Deng ◽  
Kazuo Ogawa ◽  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welded Joints ◽  
Nuclear Power ◽  
Power Plants ◽  
Butt Joint ◽  
Welding Residual Stress ◽  
Dissimilar Metal ◽  
Water Reactors

Recent discoveries of stress corrosion cracking (SCC) at nickel-based metals in pressurized water reactors (PWRs) and boiling water reactors (BWRs) have raised concerns about safety and integrity of plant components. It has been recognized that welding residual stress is an important factor causing the issue of SCC in a weldment. In this study, both numerical simulation technology and experimental method were employed to investigate the characteristics of welding residual stress distribution in several typical welded joints, which are used in nuclear power plants. These joints include a thick plate butt-welded Alloy 600 joint, a dissimilar metal J-groove set-in joint and a dissimilar metal girth-butt joint. First of all, numerical simulation technology was used to predict welding residual stresses in these three joints, and the influence of heat source model on welding residual stress was examined. Meanwhile, the influence of other thermal processes such as cladding, buttering and heat treatment on the final residual stresses in the dissimilar metal girth-butt joint was also clarified. Secondly, we also measured the residual stresses in three corresponding mock-ups. Finally, the comparisons of the simulation results and the measured data have shed light on how to effectively simulate welding residual stress in these typical joints.

Numerical Simulation for Residual Stress and Deformation of Surface Welding on Membrane Water-Wall

2014 ◽  
Vol 490-491 ◽  
pp. 594-599
Author(s):  
Fan Ling Meng ◽  
Ai Guo Liu
Keyword(s):  
Residual Stress ◽  
Great Influence ◽  
Residual Deformation ◽  
Welding Residual Stress ◽  
Finite Element Software ◽  
Welding Sequence ◽  
Surface Welding ◽  
Stress And Deformation ◽  
Welding Sequences ◽  
Residual Stress And Deformation

Automatic MIG was adopted to weld Inconel 625 alloy on 20 G Membrane Waterwall, which can improve the capacities of high temperature corrosion resistance and wear resistance. To study the influence of Membrane Waterwall surface welding sequences on residual stress and residual deformation, this paper utilized finite element software ABAQUS and segmented moving heat source model to simulate the sequence welding, balanced welding from the middle to sides, balanced welding from sides to the middle, balanced skip welding from middle to sides and balanced skip welding from sides to the middle and studied their residual stresses and deformations. The simulation results indicated that there was a great influence of welding sequences on the residual stress and deformation. The optimal welding sequence was balanced skip welding from middle to sides and balanced skip welding from sides to the middle, which could change the stress distribution, decrease the welding residual stress by 17%, realize the even deformation of the whole welding section and decrease the bending deformation by 50%.

Research on the Effects of Welding Sequence on Welding Residual Stress of High-Speed Train Based on SYSWELD

2011 ◽  
Vol 399-401 ◽  
pp. 1806-1811
Author(s):  
Yong Hong Chen ◽  
Peng Chen ◽  
Ai Qin Tian
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
High Speed ◽  
Element Model ◽  
Welding Residual Stress ◽  
High Speed Train ◽  
Distribution Law ◽  
Element Analysis ◽  
Welding Sequence ◽  
Maximum Residual Stress

The finite element model of the roof of aluminum high-speed train was established, double ellipsoid heat source was employed, and heat elastic-plastic theory was used to simulate welding residual stress of the component under different welding sequence based on the finite element analysis software SYSWELD. The distribution law of welding residual stress was obtained. And the effects of the welding sequence on the value and distribution of residual stress was analyzed. The numerical results showed that the simulation data agree well with experimental test data. The maximum residual stress appears in the weld seam and nearby. The residual stress value decreases far away from the welding center. Welding sequence has a significant impact on the final welding residual stress when welding the roof of aluminum body. The side whose residual stress needs to be controlled should be welded first.

Numerical simulation of the effect of ultrasonic impact treatment on welding residual stress

2021 ◽  
pp. 2150175
Author(s):  
Tao Mo ◽  
Jingqing Chen ◽  
Pengju Zhang ◽  
Wenqian Bai ◽  
Xiao Mu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Compressive Stress ◽  
Welded Joints ◽  
Welding Process ◽  
Residual Compressive Stress ◽  
Welding Residual Stress ◽  
304 Stainless Steel ◽  
Residual Tensile Stress ◽  
Ultrasonic Impact Treatment

Ultrasonic impact treatment (UIT) is an effective method that has been widely applied in welding structure to improve the fatigue properties of materials. It combines mechanical impact and ultrasonic vibration to produce plastic deformation on the weld joints surface, which introduces beneficial compressive residual stress distribution. To evaluate the effect of UIT technology on alleviating the residual stress of welded joints, a novel numerical analysis method based on the inherent strain theory is proposed to simulate the stress superposition of welding and subsequent UIT process of 304 stainless steel. Meanwhile, the experiment according to the process was carried out to verify the simulation of residual stress values before and after UIT. By the results, optimization of UIT application could effectively reduce the residual stress concentration after welding process. Residual tensile stress of welded joints after UIT is transformed into residual compressive stress. UIT formed a residual compressive stress layer with a thickness of about 0.13 mm on the plate. The numerical simulation results are consistent with the experimental results. The work in this paper could provide theoretical basis and technical support for the reasonable evaluation of the ultrasonic impact on residual stress elimination and mechanical properties improvement of welded joints.

scholarly journals Residual Stress Distribution in Feal Weld Overlay on Steel

1994 ◽  
Vol 364 ◽  
Author(s):  
X.-L. Wang ◽  
S. Spooner ◽  
C. R. Hubbard ◽  
P. J. Maziasz ◽  
G. M. Goodwin ◽  
...  
Keyword(s):  
Experimental Data ◽  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Post Weld Heat Treatment ◽  
Residual Stress Distribution ◽  
Element Analysis ◽  
Weld Overlay

AbstractNeutron diffraction was used to measure the residual stress distribution in an FeAl weld overlay on steel. It was found that the residual stresses accumulated during welding were essentially removed by the post-weld heat treatment that was applied to the specimen; most residual stresses in the specimen developed during cooling following the post-weld heat treatment. The experimental data were compared with a plasto-elastic finite element analysis. While some disagreement exists in absolute strain values, there is satisfactory agreement in strain spatial distribution between the experimental data and the finite element analysis.

A Probabilistic Evaluation Model for Welding Residual Stress Distribution at Piping Joint in Probabilistic Fracture Mechanics Analysis

2008 ◽  
Author(s):  
Hiroto Itoh ◽  
Jinya Katsuyama ◽  
Kunio Onizawa
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Fracture Mechanics ◽  
Failure Probability ◽  
Evaluation Model ◽  
Residual Stress Distribution ◽  
Welding Residual Stress ◽  
Probabilistic Fracture Mechanics ◽  
Probabilistic Evaluation ◽  
Aging Knowledge

Stress corrosion cracking (SCC) has been observed at some piping joints made by Austenitic stainless steel in BWR plants. In JAEA, we have been developing probabilistic fracture mechanics (PFM) analysis methods for aged piping based on latest aging knowledge and an analytical code, PASCAL-SP. PASCAL-SP evaluates the failure probability of piping at aged welded joints under SCC by a Monte Carlo method. We proposes a simplified probabilistic model which can be applied to the failure probability analysis based on PFM for welded joint of piping considering the uncertainty of welding residual stress. And the probabilistic evaluation model is introduced to PASCAL-SP. A parametric PFM analysis concerning uncertainties of residual stress distribution using PASCAL-SP was performed. The PFM analysis showed that the uncertainties of residual stress distribution largely influenced break probability. The break probability increased with increasing the uncertainties of residual stress.

Sign in / Sign up

Export Citation Format

Share Document