scholarly journals Effect of Cu on the Fracture and Exfoliation Corrosion Behavior of Al-Zn-Mg-xCu Alloy

Metals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 1048 ◽  
Author(s):  
Huibin Jiao ◽  
Kanghua Chen ◽  
Songyi Chen ◽  
Zhen Yang ◽  
Peng Xie ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Exfoliation Corrosion ◽  
Cu Content ◽  
Short Transverse ◽  
Transmission Electron ◽  
Corrosion Behaviors ◽  
Mechanical Tensile ◽  
Scanning Electron ◽  
Better Than

In the present work, the influence of Cu content on microstructure, mechanical properties and exfoliation corrosion behaviors of Al-Zn-Mg-xCu alloy extrusions has been investigated in longitudinal-transverse (L-T) and short-longitudinal (S-L) directions by means of mechanical tensile and exfoliation corrosion testing combined with optical microscopy (OM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results showed that a higher Cu content significantly decreased the fracture toughness and ductility of the alloy in S-L direction compared with L-T direction. Concomitant with the increase in Cu content, a transition in fracture mode was observed from transgranular dimpled rupture to intergranular rupture in S-L direction. Moreover, the exfoliation corrosion (EXCO) resistance of the alloy decreased as the Cu content increased and the exfoliation corrosion resistance of the alloy in short-transverse (S-T) direction was better than that of L-T direction. These results were mainly associated with the large number of coarse intermetallics caused by high Cu content in the L-T direction of alloy.

Electron Microscopic Observation of the Longitudinal Organization of Poly (p-Phenylene Terephthalamide) Fibers

1982 ◽  
Vol 40 ◽  
pp. 680-681
Author(s):  
Li Li-Sheng ◽  
L.F. Allard ◽  
W.C. Bigelow
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Microscopic Observation ◽  
Electron Microscopic Observation ◽  
Electron Microscopic ◽  
Aromatic Polyamides ◽  
Radial Arrangement ◽  
Scanning Electron ◽  
Better Than

The aromatic polyamides form a class of fibers having mechanical properties which are much better than those of aliphatic polyamides. Currently, the accepted morphology of these fibers as proposed by M.G. Dobb, et al. is a radial arrangement of pleated sheets, with the plane of the pleats parallel to the axis of the fiber. We have recently obtained evidence which supports a different morphology of this type of fiber, using ultramicrotomy and ion-thinning techniques to prepare specimens for transmission and scanning electron microscopy.

Scanning Secondary Electron Microscopy of Myofibrils Using Transmission Techniques

1975 ◽  
Vol 33 ◽  
pp. 556-557
Author(s):  
M. K. Lamvik
Keyword(s):  
Electron Microscopy ◽  
Electron Microscope ◽  
Carbon Films ◽  
Photographic Recording ◽  
Transmission Electron ◽  
Thin Carbon ◽  
The Common ◽  
Scanning Electron ◽  
Better Than ◽  
Cellular Organelles

When observing small objects such as cellular organelles by scanning electron microscopy, it is often valuable to use the techniques of transmission electron microscopy. The common practice of mounting and coating for SEM may not always be necessary. These possibilities are illustrated using vertebrate skeletal muscle myofibrils.Micrographs for this study were made using a Hitachi HFS-2 scanning electron microscope, with photographic recording usually done at 60 seconds per frame. The instrument was operated at 25 kV, with a specimen chamber vacuum usually better than 10-7 torr. Myofibrils were obtained from rabbit back muscle using the method of Zak et al. To show the component filaments of this contractile organelle, the myofibrils were partially disrupted by agitation in a relaxing medium. A brief centrifugation was done to clear the solution of most of the undisrupted myofibrils before a drop was placed on the grid. Standard 3 mm transmission electron microscope grids covered with thin carbon films were used in this study.

Microstructure Evolution and Mechanical Properties of an Al-Cu-Mg Alloy at Elevated Temperature

2014 ◽  
Vol 1004-1005 ◽  
pp. 148-153
Author(s):  
Min Hao ◽  
Ji Gang Ru ◽  
Ming Liu ◽  
Kun Zhang ◽  
Liang Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Elevated Temperature ◽  
Elevated Temperatures ◽  
Shear Fracture ◽  
S Phase ◽  
Mg Alloy ◽  
Transmission Electron ◽  
Fracture Features ◽  
Scanning Electron

Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were utilized to study the microstructure and mechanical behavior of an Al-Cu-Mg alloy after tensile test at 125°C, 150°C, 175°C and 200 °C, respectively. The yield strength and ultimate tensile strength decreased with the increase of temperature, while the elongation increased firstly and then decreased. The S and S′ precipitate after tension at elevated temperatures. When the temperature was higher than 175°C, the precipitate coarsens rapidly. The alloys displayed a shear fracture features at elevated temperature. The larger S′ and S phase coarsened and dropped which forming crack in the grain boundaries and precipitate interfaces, resulting in the decrease of the elongation of the alloy.

scholarly journals Study on Grain Refinement Mechanisms and Mechanical Properties of bi-Modal Ti-55511 Titanium Alloy during Hot Rolling

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3351 ◽  
Author(s):  
Wei Chen ◽  
Xiaoyong Zhang ◽  
YongCheng Lin ◽  
Kechao Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Hot Rolling ◽  
Shear Bands ◽  
High Ductility ◽  
Α Phase ◽  
Transmission Electron ◽  
Scanning Electron

Multi-pass hot rolling was performed on bi-modal Ti-55511 alloy with 50% rolling reduction at 700 °C. Mechanical properties were evaluated by tensile test, and microstructure evolution was characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results show that the Ti-55511 alloy with bi-modal microstructure exhibits good strength and high ductility (1102 MPa, 21.7%). Comparatively, after 50% hot rolling, an enhanced strength and decreased ductility were obtained. The refinement of α phases leads to the increased tensile strength, while the fragmentation of the equiaxed α phase results in a decreased ductility. The fragmentation process of equiaxed α phases followed the sequence of: elongation of α phases → formation of grooves and localized shear bands → the final fragmentation accomplished via deepening grooves.

Surface-modified halloysite nanotubes as fillers applied in reinforcing the performance of polytetrafluoroethylene

Clay Minerals ◽  
2018 ◽  
Vol 53 (4) ◽  
pp. 643-656 ◽  
Author(s):  
Zhi-Lin Cheng ◽  
Xing-Yu Chang ◽  
Zan Liu ◽  
Dun-Zhong Qin
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Sodium Dodecyl ◽  
Halloysite Nanotubes ◽  
Angle Measurements ◽  
Transmission Electron ◽  
Contact Angle Measurements ◽  
Ftir Spectrometry ◽  
Surface Modified ◽  
Scanning Electron

ABSTRACTIn order to improve the dispersibility of halloysite nanotubes (HNTs) in polytetrafluoroethylene (PTFE), the modification of HNT surfaces was studied with three types of modifiers (polymethyl methacrylate [PMMA], sodium dodecyl sulfate [SDS] and carboxylic acid). The modified HNTs were characterized by Fourier-transform infrared (FTIR) spectrometry, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and contact angle measurements. The HNTs were used to reinforce the mechanical properties of PTFE. The mechanical results indicated that the tensile strength of the modified HNT-filled PTFE nanocomposites (F-HNT/PTFE) improved to an acceptable degree and Young's modulus increased significantly. The tribological results showed that the wear rate of F-HNT/PTFE decreased by 21–82 and 9–40 times compared to pure PTFE and the pristine F-HNT/PTFE, respectively.

scholarly journals Development of Flexible Polyurethane Nanostructured Biocomposite Foams Derived from Palm Olein-Based Polyol

2016 ◽  
Vol 2016 ◽  
pp. 1-12 ◽  
Author(s):  
Srihanum Adnan ◽  
Tuan Noor Maznee Tuan Ismail ◽  
Norhayati Mohd Noor ◽  
Nik Siti Mariam Nek Mat Din ◽  
Nurul ‘Ain Hanzah ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Palm Olein ◽  
Nanocomposite Foams ◽  
Transmission Electron ◽  
Flexible Polyurethane ◽  
Pu Foams ◽  
Scanning Electron

This study examined the effect of organoclay montmorillonite (OMMT) on the mechanical properties and morphology of flexible polyurethane/OMMT nanocomposite (PU/OMMT) foams prepared from petroleum- and palm olein-based polyols. Palm-based PU foams exhibited inferior mechanical strength as compared to neat petroleum PU foams. However, addition of OMMT significantly improved the foams strength of flexible polyurethane/OMMT nanocomposite foams prepared from palm olein-based polyol (PU bionanocomposite foam). The morphology analysed by scanning electron microscopy (SEM) showed that the cell size of the foam decreased with increasing OMMT content. PU bionanocomposite foam with 5 wt% of OMMT had the most improved tensile (63%) and tear (48%) strengths compared to its neat counterpart. Transmission electron microscopy (TEM) revealed the exfoliated structure of the respective foam. It was concluded that OMMT improved mechanical properties and morphology of PU foams.

Effects of Thermal Treatment on the Morphology and Properties of CSM/Poly(Urethane-Isocyanurate) Composites Formed by SRIM Process

2008 ◽  
Vol 575-578 ◽  
pp. 941-946
Author(s):  
Hong Yan Tang ◽  
Ji Hui Wang ◽  
Guo Qiang Gao ◽  
Wen Xing Chen
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Mechanical Property ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Treatment Time ◽  
Microphase Separation ◽  
Scanning Calorimetry ◽  
Transmission Electron ◽  
Scanning Electron

Fiberglass continuous strand mat(CSM)/poly(urethane-isocyanurate) composites were formed by SRIM process, treated under different conditions and then characterized based on dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) ,transmission electron microscopy (TEM) and the mechanical property tests. The results show that the mechanical properties of the composites could be increased with improving the degree of microphase separation. At a given temperature (120°C), the degree of microphase separation is the highest for 4h and decreases gradually with prolonging treatment time. For a given time (4h), the well microphase-separated morphology is obtained and the degree of microphase mixing is increased at 120°C and 140°C treatments, respectively. The degree of microphase separation of the composites decreases with enhancing the temperature to 140°C.

The Effect of Tungsten on the Nucleation and Growth of thin Aluminum Alloy Films

1993 ◽  
Vol 317 ◽  
Author(s):  
Bea CAO ◽  
N. David Theodore ◽  
Hank Shin ◽  
Peter Fejes ◽  
Les Hendrickson
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Nucleation And Growth ◽  
Growth Behavior ◽  
Aluminum Films ◽  
Surface Energies ◽  
Transmission Electron ◽  
Thin Aluminum ◽  
Scanning Electron

ABSTRACTA variety of alloying elements are currently being investigated for their effects on the mechanical properties and reliability of thin aluminum films. In the present study, scanning electron microscopy and transmission electron microscopy are used to study the nucleation and growth of Al-1.5wt%Cu and Al-1.5wt% Cu-0.2wt% W films. Differences in Microstructure, nucleation and growth behavior are observed and are explained in terms of changes in surface energies and atomic Mobilities.

The Microstructure and Tribological Behavior of Ti/a-C and Ti/a-C:H Films Prepared by Magnetron Sputtering

2013 ◽  
Vol 420 ◽  
pp. 123-128
Author(s):  
Chun Fu Hong ◽  
Jian Zhong Wang ◽  
Wei Yan ◽  
Ang Ding ◽  
Zhi Yong Liu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Magnetron Sputtering ◽  
Tribological Behavior ◽  
Carbon Matrix ◽  
High Wear Resistance ◽  
Transmission Electron ◽  
Scanning Electron

This paper reports two films, Ti/a-C and Ti/a-C:H, prepared on the Ti-6Al-4V alloys by magnetron sputtering in PVD and CVD process, respectively. The morphology and microstructure were characterized by Raman spectroscopy, scanning electron microscopy and transmission electron microscopy. Both films show nanosized Ti clusters incorporated into the amorphous carbon matrix. Mechanical properties of the films were investigated by nanoindentation and ball-on-disk tribo-test. Ti/a-C film shows a hardness as high as 40.9 GPa, while that of Ti/a-C:H is 12.2 GPa. Both films show reduced friction and high wear resistance.

scholarly journals Fabrication, Mechanical Properties and In-Vitro Behavior of Akermanite Bioceramic

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4887
Author(s):  
Fariborz Tavangarian ◽  
Caleb A. Zolko ◽  
Sorour Sadeghzade ◽  
Marwan Fayed ◽  
Keivan Davami
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Subsequent Annealing ◽  
Apatite Formation ◽  
X Ray ◽  
Transmission Electron ◽  
Powder Samples ◽  
Sbf Solution ◽  
Scanning Electron

Pure nanocrystalline akermanite (Ca2MgSi2O7) powder was synthesized by mechanical activation with subsequent annealing of talc, calcium carbonate, and silicate powders as the initial materials. Powder samples were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and transmission electron microscopy (TEM) techniques. The results showed that pure nanocrystalline akermanite with a crystalline size of 35 nm was synthesized after ball milling the initial powders for 20 h with subsequent annealing at 900 °C for 1 h. Mechanical properties of bulk akermanite samples were studied as well. The results showed that the produced akermanite tablets sintered at 1200 °C for 5 h had a Young’s modulus of 3800 MPa, an ultimate compressive strength of 24.7 MPa, and a density of 2.489 g/cm3. The in-vitro behavior of the produced akermanite was evaluated by soaking the samples in an SBF solution. The results showed that the produced akermanite had the apatite formation ability on its surface and can be a good candidate for bone tissue engineering applications.

Sign in / Sign up

Export Citation Format

Share Document