scholarly journals An Optimized Flutter-Driven Triboelectric Nanogenerator with a Low Cut-In Wind Speed

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 366
Author(s):  
Yang Xia ◽  
Yun Tian ◽  
Lanbin Zhang ◽  
Zhihao Ma ◽  
Huliang Dai ◽  
...  

We present an optimized flutter-driven triboelectric nanogenerator (TENG) for wind energy harvesting. The vibration and power generation characteristics of this TENG are investigated in detail, and a low cut-in wind speed of 3.4 m/s is achieved. It is found that the air speed, the thickness and length of the membrane, and the distance between the electrode plates mainly determine the PTFE membrane’s vibration behavior and the performance of TENG. With the optimized value of the thickness and length of the membrane and the distance of the electrode plates, the peak open-circuit voltage and output power of TENG reach 297 V and 0.46 mW at a wind speed of 10 m/s. The energy generated by TENG can directly light up dozens of LEDs and keep a digital watch running continuously by charging a capacitor of 100 μF at a wind speed of 8 m/s.

2012 ◽  
Vol 503 ◽  
pp. 71-74
Author(s):  
Xing Qiang Zhao ◽  
Zhi Yu Wen ◽  
Zhi Gang Du

A novel miniaturized piezoelectric wind flutter generator is proposed which consisted of a flexible beam and a PZT cantilever. The working principle is based on flexible beam flutter, which can amplify the PZT cantilever vibration. A prototype was tested in a wind tunnel. It is found that there are three behavior states with wind speed increasing, and flutter behavior takes place when wind speed varies between the critical wind speed Uc1and Uc2, an empirical formula was obtained about the critical speed Uc1. The open circuit voltage and power were measured. The device can generate 794μW output power with 30kΩ resistor in a wind of speed 20m/s, power density is 139μW/cm3.


2021 ◽  
pp. 1-12
Author(s):  
Ting Zhao ◽  
Kewen Li ◽  
Yuhao Zhu ◽  
Lin Jia ◽  
Xiaoyong Hou ◽  
...  

Abstract Thermoelectric generators (TEG) are widely used in many industries. The voltage and output power of TEG chips are critical indicators to evaluate the performance of TEGs. The conventional method is to directly test the output voltage and power of the whole TEG chip that contains 127 pairs of PN (P- and N-type) legs (127-PN-TEG). However, the assembling of these PN legs is very time-consuming. In order to reduce experimental time and the consumption of TEG materials, we proposed an experimental method. We developed the test apparatus for the rapid evaluation of TEG performance using a TEG chip with a single pair of PN legs (1-PN-TEG). We made several 1-PN-TEGs and 127-PN-TEGs using the same thermoelectric material (bismuth telluride). We then measured the voltage and the power of these 1-PN-TEGs and 127-PN-TEGs, respectively. The experimental results were compared and analyzed. The comparison showed that the voltage of 127-PN-TEG is equal to the voltage of 1-PN-TEG times 127, which implies that we could use the test data of 1-PN-TEG to evaluate the performance of 127-PN-TEG. Using the experimental device developed in this paper, we also studied the effects of the PN leg area (cross-sectional area of PN legs) and the pressure applied over the TEGs on the output power of 1-PN-TEG. The experimental results showed that the power per unit area decreases with an increase in the 1-PN-TEG's PN leg area when the temperature difference between the hot and cold sides was constant. Under a specific temperature difference conditions, the open-circuit voltage and the output power will increase with the pressure applied on the TEG chips.


2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Hashwini Lalchand Thadani ◽  
Fadia Dyni Zaaba ◽  
Muhammad Raimi Mohammad Shahrizal ◽  
Arjun Singh Jaj A. Jaspal Singh Jaj ◽  
Yun Ii Go

PurposeThis paper aims to design an optimum vertical axis wind turbine (VAWT) and assess its techno-economic performance for wind energy harvesting at high-speed railway in Malaysia.Design/methodology/approachThis project adopted AutoCAD and ANSYS modeling tools to design and optimize the blade of the turbine. The site selected has a railway of 30 km with six stops. The vertical turbines are placed 1 m apart from each other considering the optimum tip speed ratio. The power produced and net present value had been analyzed to evaluate its techno-economic viability.FindingsComputational fluid dynamics (CFD) analysis of National Advisory Committee for Aeronautics (NACA) 0020 blade has been carried out. For a turbine with wind speed of 50 m/s and swept area of 8 m2, the power generated is 245 kW. For eight trains that operate for 19 h/day with an interval of 30 min in nonpeak hours and 15 min in peak hours, total energy generated is 66 MWh/day. The average cost saved by the train stations is RM 16.7 mil/year with battery charging capacity of 12 h/day.Originality/valueWind energy harvesting is not commonly used in Malaysia due to its low wind speed ranging from 1.5 to 4.5 m/s. Conventional wind turbine requires a minimum cut-in wind speed of 11 m/s to overcome the inertia and starts generating power. Hence, this paper proposes an optimum design of VAWT to harvest an unconventional untapped wind sources from railway. The research finding complements the alternate energy harvesting technologies which can serve as reference for countries which experienced similar geographic constraints.


Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1625 ◽  
Author(s):  
Massimo Mariello ◽  
Elisa Scarpa ◽  
Luciana Algieri ◽  
Francesco Guido ◽  
Vincenzo Mariano Mastronardi ◽  
...  

Triboelectric nanogenerators (TENGs) have recently become a powerful technology for energy harvesting and self-powered sensor networks. One of their main advantages is the possibility to employ a wide range of materials, especially for fabricating inexpensive and easy-to-use devices. This paper reports the fabrication and preliminary characterization of a novel flexible triboelectric nanogenerator which could be employed for driving future low power consumption wearable devices. The proposed TENG is a single-electrode device operating in contact-separation mode for applications in low-frequency energy harvesting from intermittent tapping loads involving the human body, such as finger or hand tapping. The novelty of the device lies in the choice of materials: it is based on a combination of a polysiloxane elastomer and a poly (para-xylylene). In particular, the TENG is composed, sequentially, of a poly (dimethylsiloxane) (PDMS) substrate which was made porous and rough with a steam-curing step; then, a metallization layer with titanium and gold, deposited on the PDMS surface with an optimal substrate–electrode adhesion. Finally, the metallized structure was coated with a thin film of parylene C serving as friction layer. This material provides excellent conformability and high charge-retaining capability, playing a crucial role in the triboelectric process; it also makes the device suitable for employment in harsh, wet environments owing to its inertness and barrier properties. Preliminary performance tests were conducted by measuring the open-circuit voltage and power density under finger tapping (~2 N) at ~5 Hz. The device exhibited a peak-to-peak voltage of 1.6 V and power density peak of 2.24 mW/m2 at ~0.4 MΩ. The proposed TENG demonstrated ease of process, simplicity, cost-effectiveness, and flexibility.


Energies ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 4246 ◽  
Author(s):  
Guglielmo D’Amico ◽  
Giovanni Masala ◽  
Filippo Petroni ◽  
Robert Adam Sobolewski

Because of the stochastic nature of wind turbines, the output power management of wind power generation (WPG) is a fundamental challenge for the integration of wind energy systems into either power systems or microgrids (i.e., isolated systems consisting of local wind energy systems only) in operation and planning studies. In general, a wind energy system can refer to both one wind farm consisting of a number of wind turbines and a given number of wind farms sited at the area in question. In power systems (microgrid) planning, a WPG should be quantified for the determination of the expected power flows and the analysis of the adequacy of power generation. Concerning this operation, the WPG should be incorporated into an optimal operation decision process, as well as unit commitment and economic dispatch studies. In both cases, the probabilistic investigation of WPG leads to a multivariate uncertainty analysis problem involving correlated random variables (the output power of either wind turbines that constitute wind farm or wind farms sited at the area in question) that follow different distributions. This paper advances a multivariate model of WPG for a wind farm that relies on indexed semi-Markov chains (ISMC) to represent the output power of each wind energy system in question and a copula function to reproduce the spatial dependencies of the energy systems’ output power. The ISMC model can reproduce long-term memory effects in the temporal dependence of turbine power and thus understand, as distinct cases, the plethora of Markovian models. Using copula theory, we incorporate non-linear spatial dependencies into the model that go beyond linear correlations. Some copula functions that are frequently used in applications are taken into consideration in the paper; i.e., Gumbel copula, Gaussian copula, and the t-Student copula with different degrees of freedom. As a case study, we analyze a real dataset of the output powers of six wind turbines that constitute a wind farm situated in Poland. This dataset is compared with the synthetic data generated by the model thorough the calculation of three adequacy indices commonly used at the first hierarchical level of power system reliability studies; i.e., loss of load probability (LOLP), loss of load hours (LOLH) and loss of load expectation (LOLE). The results will be compared with those obtained using other models that are well known in the econometric field; i.e., vector autoregressive models (VAR).


2020 ◽  
Vol 8 (45) ◽  
pp. 23894-23905
Author(s):  
Hwa Sook Ryu ◽  
Hyun Gyeong Lee ◽  
Sang-Chul Shin ◽  
Jooho Park ◽  
Sang Hyeon Kim ◽  
...  

Terminal alkyl substituents in IDIC nonfullerene acceptors improve light absorption, crystalline packing and charge mobility in films.


Author(s):  
Budiyanto Budiyanto ◽  
Fadliondi Fadliondi

This paper explains the experimental investigation to improve the output power of solar cell using cooling and light reflection from mirrors. The results show that by adding mirror, the current and output power of solar cell increase but the open circuit voltage and maximum power voltage decrease due to heat. By adding cooling, the open circuit voltage and the maximum power voltage are improved, so the output power also increases.


Author(s):  
S. Hashimoto ◽  
Y. Liu ◽  
K. Asano ◽  
M. Mori ◽  
Y. Funahashi ◽  
...  

A micro tubular solid oxide fuel cell (SOFC) bundle was developed based on new concept. The anode-supported micro tubular SOFCs with the cell configuration, La0.6Sr0.4Co0.2Fe0.8 O3−δ (LSCF) – Ce0.9Gd0.1O2−δ (CGO) cathode / CGO electrolyte / Ni – CGO anode were fabricated and were bundled by a porous LSCF current collecting cube 1 cm on a side. The power generation test of the fabricated SOFC bundle was carried out under pressurized conditions. Using wet 30%H2 / N2 mixture gas and air, the cubic power density of the bundle at 500°C was 0.47 Wcm−3 at 0.4Acm−2, atmospheric pressure (0.1MPa). With increasing operating pressure, the performance has been improved, and the cubic power density finally reached to 0.66 Wcm−3 at 0.6MPa. Pressurization effect for the power improvement was brought about by the open circuit voltage enhancement and reduction of the polarization resistance.


Sign in / Sign up

Export Citation Format

Share Document