scholarly journals Mesoporous Carbons from Polysaccharides and Their Use in Li-O2 Batteries

Nanomaterials ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 2036
Author(s):  
María Uriburu-Gray ◽  
Aránzazu Pinar-Serrano ◽  
Gokhan Cavus ◽  
Etienne Knipping ◽  
Christophe Aucher ◽  
...  
Keyword(s):  
Ionic Liquid ◽  
Carbon Material ◽  
Low Cost ◽  
Specific Capacity ◽  
Cell Performance ◽  
Mesoporous Carbons ◽  
Mesopore Volume ◽  
Battery Cell ◽  
N Doping

Previous studies have demonstrated that the mesoporosity of carbon material obtained by the Starbon® process from starch-formed by amylose and amylopectin can be tuned by controlling this ratio (the higher the amylose, the higher the mesoporosity). This study shows that starch type can also be an important parameter to control this mesoporosity. Carbons with controlled mesoporosity (Vmeso from 0.1–0.7 cm3/g) have been produced by the pre-mixing of different starches using an ionic liquid (IL) followed by a modified Starbon® process. The results show that the use of starch from corn and maize (commercially available Hylon VII with maize, respectively) is the better combination to increase the mesopore volume. Moreover, “low-cost” mesoporous carbons have been obtained by the direct carbonization of the pre-treated starch mixtures with the IL. In all cases, the IL can be recovered and reused, as demonstrated by its recycling up to three times. Furthermore, and as a comparison, chitosan has been also used as a precursor to obtain N-doped mesoporous carbons (5.5 wt% N) with moderate mesoporosity (Vmeso = 0.43 cm3/g). The different mesoporous carbons have been tested as cathode components in Li-O2 batteries and it is shown that a higher carbon mesoporosity, produced from starch precursor, or the N-doping, produced from chitosan precursor, increase the final battery cell performance (specific capacity and cycling).

scholarly journals Controlled Nanostructuration of Cobalt Oxyhydroxide Electrode Material for Hybrid Supercapacitors

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2325
Author(s):  
Ronan Invernizzi ◽  
Liliane Guerlou-Demourgues ◽  
François Weill ◽  
Alexia Lemoine ◽  
Marie-Anne Dourges ◽  
...  
Keyword(s):  
Ionic Liquid ◽  
Ionic Liquids ◽  
Energy Storage ◽  
Specific Surface ◽  
Electrode Materials ◽  
Specific Capacity ◽  
Hybrid Supercapacitors ◽  
Cobalt Oxyhydroxide ◽  
Precipitation Medium ◽  
The Impact

Nanostructuration is one of the most promising strategies to develop performant electrode materials for energy storage devices, such as hybrid supercapacitors. In this work, we studied the influence of precipitation medium and the use of a series of 1-alkyl-3-methylimidazolium bromide ionic liquids for the nanostructuration of β(III) cobalt oxyhydroxides. Then, the effect of the nanostructuration and the impact of the different ionic liquids used during synthesis were investigated in terms of energy storage performances. First, we demonstrated that forward precipitation, in a cobalt-rich medium, leads to smaller particles with higher specific surface areas (SSA) and an enhanced mesoporosity. Introduction of ionic liquids (ILs) in the precipitation medium further strongly increased the specific surface area and the mesoporosity to achieve well-nanostructured materials with a very high SSA of 265 m2/g and porosity of 0.43 cm3/g. Additionally, we showed that ILs used as surfactant and template also functionalize the nanomaterial surface, leading to a beneficial synergy between the highly ionic conductive IL and the cobalt oxyhydroxide, which lowers the resistance charge transfer and improves the specific capacity. The nature of the ionic liquid had an important influence on the final electrochemical properties and the best performances were reached with the ionic liquid containing the longest alkyl chain.

The Coralloid-carbon Material Based on Biomass as Promising Anode Material for Lithium and Sodium Storage

2021 ◽  
Author(s):  
Ziqiang Yu ◽  
Zhiqiang Zhao ◽  
Tingyue Peng
Keyword(s):  
Lithium Ion Battery ◽  
Anode Material ◽  
Carbon Material ◽  
Specific Capacity ◽  
Lithium Ion ◽  
High Specific Capacity ◽  
Further Development ◽  
Sodium Storage ◽  
Cycling Life

Lithium ion battery (LIB), advantageous in high specific capacity, long cycling life and eco-friendly, has been widely used in many fields. The dwindling reserves, however, limit the further development. Sharing...

Low cost earthworm manure-derived carbon material for the adsorption of Cu 2+ from aqueous solution: Impact of pyrolysis temperature

2017 ◽  
Vol 98 ◽  
pp. 189-195 ◽  
Author(s):  
Bin Zhou ◽  
Zhanghong Wang ◽  
Dekui Shen ◽  
Fei Shen ◽  
Chunfei Wu ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Carbon Material ◽  
Pyrolysis Temperature ◽  
Low Cost

scholarly journals Improvement of long-term cycling performance of high-nickel cathode materials by ZnO coating

2021 ◽  
Vol 10 (1) ◽  
pp. 210-220
Author(s):  
Fangfang Wang ◽  
Ruoyu Hong ◽  
Xuesong Lu ◽  
Huiyong Liu ◽  
Yuan Zhu ◽  
...  
Keyword(s):  
Electrochemical Performance ◽  
Lithium Ion Batteries ◽  
Solid Phase ◽  
Low Cost ◽  
Specific Capacity ◽  
High Capacity ◽  
Lithium Ion ◽  
Side Reaction ◽  
Chemical Route ◽  
High Nickel

Abstract The high-nickel cathode material of LiNi0.8Co0.15Al0.05O2 (LNCA) has a prospective application for lithium-ion batteries due to the high capacity and low cost. However, the side reaction between the electrolyte and the electrode seriously affects the cycling stability of lithium-ion batteries. In this work, Ni2+ preoxidation and the optimization of calcination temperature were carried out to reduce the cation mixing of LNCA, and solid-phase Al-doping improved the uniformity of element distribution and the orderliness of the layered structure. In addition, the surface of LNCA was homogeneously modified with ZnO coating by a facile wet-chemical route. Compared to the pristine LNCA, the optimized ZnO-coated LNCA showed excellent electrochemical performance with the first discharge-specific capacity of 187.5 mA h g−1, and the capacity retention of 91.3% at 0.2C after 100 cycles. The experiment demonstrated that the improved electrochemical performance of ZnO-coated LNCA is assigned to the surface coating of ZnO which protects LNCA from being corroded by the electrolyte during cycling.

scholarly journals Multiscale additive manufacturing of polymers using 3D photo-printable self-assembling ionic liquid monomers

2019 ◽  
Vol 4 (3) ◽  
pp. 580-585 ◽  
Author(s):  
Bineh G. Ndefru ◽  
Bryan S. Ringstrand ◽  
Sokhna I.-Y. Diouf ◽  
Sönke Seifert ◽  
Juan H. Leal ◽  
...  
Keyword(s):  
Ionic Liquid ◽  
Additive Manufacturing ◽  
Self Assembly ◽  
Low Cost ◽  
Low Resolution ◽  
Top Down ◽  
Bottom Up ◽  
Cost Approach ◽  
Self Assembling ◽  
Nanoscale Features

Combining bottom-up self-assembly with top-down 3D photoprinting affords a low cost approach for the introduction of nanoscale features into a build with low resolution features.

Carbonyl-Iron Electrodes for Rechargeable-Iron Batteries

2015 ◽  
Vol 1 (1) ◽  
Author(s):  
A. Sundar Rajan ◽  
M. K. Ravikumar ◽  
K. R. Priolkar ◽  
S. Sampath ◽  
A. K. Shukla
Keyword(s):  
Carbonyl Iron ◽  
Large Scale ◽  
Low Cost ◽  
Specific Capacity ◽  
Electrical Energy ◽  
Slow Increase ◽  
Faradaic Efficiency ◽  
Nickel Iron ◽  
In Situ Xrd ◽  
Iron Electrodes

AbstractNickel-iron and iron-air batteries are attractive for large-scale-electrical-energy storage because iron is abundant, low-cost and non-toxic. However, these batteries suffer from poor charge acceptance due to hydrogen evolution during charging. In this study, we have demonstrated iron electrodes prepared from carbonyl iron powder (CIP) that are capable of delivering a specific discharge capacity of about 400 mAh g−1 at a current density of 100 mA g−1 with a faradaic efficiency of about 80%. The specific capacity of the electrodes increases gradually during formation cycles and reaches a maximum in the 180th cycle. The slow increase in the specific capacity is attributed to the low surface area and limited porosity of the pristine CIP. Evolution of charge potential profiles is investigated to understand the extent of charge acceptance during formation cycles. In situ XRD pattern for the electrodes subsequent to 300 charge/discharge cycles confirms the presence of Fe with Fe(OH)2 as dominant phase.

The Selective Oxidation of Hydrocarbons on Isolated Iron Active Sites under Ambient Conditions

2019 ◽  
Vol 41 (6) ◽  
pp. 946-946
Author(s):  
Zhengliang Qi Zhengliang Qi ◽  
Junmei Liu Junmei Liu ◽  
Wanwan Guo and Jun Huang Wanwan Guo and Jun Huang
Keyword(s):  
Ionic Liquid ◽  
Activated Carbon ◽  
Carbon Material ◽  
Active Sites ◽  
High Selectivity ◽  
Good Activity ◽  
Ambient Conditions ◽  
Oxidation Of Hydrocarbons ◽  
Fe Catalysts ◽  
Iron Active Sites

The N-doped carbon material supported Fe catalysts were developed for the oxidation of C-H bond of hydrocarbons to ketones and alcohols. The supported Fe catalysts were prepared by pyrolysis of [CMIM]3Fe(CN)6 ionic liquid in activated carbon. And the Fe(Ⅲ)@CN-600 showed good activity and high selectivity for the oxidation of alfa C-H bond of alkylbenzenes. The isolated Fe(Ⅲ) iron active sites should be responsible for the high activity and selectivity for the oxidation of hydrocarbons to ketones. Several ketones were obtained in good to excellent yields. Moreover, cyclohexanone can also be obtained through the oxidation of cyclohexane.

scholarly journals Synthesis and Characterisation of Pyridinium-Based Ionic Liquid as Activating Agent in Rubber Seed Shell Activated Carbon Production for CO2 Capture

2021 ◽  
Vol 82 (1) ◽  
pp. 85-95
Author(s):  
Nawwarah Mokti ◽  
Azry Borhan ◽  
Siti Nur Azella Zaine ◽  
Hayyiratul Fatimah Mohd Zaid
Keyword(s):  
Ionic Liquid ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Co2 Capture ◽  
Low Cost ◽  
Chemical Activation ◽  
Green Technology ◽  
Activation Process ◽  
Rubber Seed ◽  
Activating Agent

The use of an activating agent in chemical activation of activated carbon (AC) production is very important as it will help to open the pore structure of AC as adsorbents and could enhance its performance for adsorption capacity. In this study, a pyridinium-based ionic liquid (IL), 1-butylpyridinium bis(trifluoromethylsulfonyl) imide, [C4Py][Tf2N] has been synthesized by using anion exchange reaction and was characterized using few analyses such as 1H-NMR, 13C-NMR and FTIR. Low-cost AC was synthesized by chemical activation process in which rubber seed shell (RSS) and ionic liquid [C4Py][Tf2N] were employed as the precursor and activating agent, respectively. AC has been prepared with different IL concentration (1% and 10%) at 500°C and 800°C for 2 hours. Sample AC2 shows the highest SBET and VT which are 392.8927 m2/g and 0.2059 cm3/g respectively. The surface morphology of synthesized AC can be clearly seen through FESEM analysis. A high concentration of IL in sample AC10 contributed to blockage of pores by the IL. On the other hand, the performance of synthesized AC for CO2 adsorption capacity also studied by using static volumetric technique at 1 bar and 25°C. Sample AC2 contributed the highest CO2 uptakes which is 50.783 cm3/g. This current work shows that the use of low concentration IL as an activating agent has the potential to produce porous AC, which offers low-cost, green technology as well as promising application towards CO2 capture.

Sign in / Sign up

Export Citation Format

Share Document