scholarly journals Polyamide 6-Aluminum Assembly Enhanced by Laser Microstructuring

Polymers ◽  
2022 ◽  
Vol 14 (2) ◽  
pp. 288
Author(s):  
Karol Bula ◽  
Bartosz Korzeniewski
Keyword(s):  
Laser Beam ◽  
Roughness Parameter ◽  
Scanning Speed ◽  
Polyamide 6 ◽  
Optical Microscope ◽  
Injection Molding Process ◽  
Molding Process ◽  
Aluminum Sheets ◽  
Lap Shear ◽  
Micro Structuring

The presented work’s aim is the application of low-power laser treatment for the enhancement of interfacial micromechanical adhesion between polyamide 6 (filled with glass fiber) and aluminum. A fiber laser beam was used to prepare micro-patterns on aluminum sheets. The micro-structuring was conducted in the regime of 50, 100, 200 and 300 mm/s laser beam speeds, for both sides. The joining process was realized in an injection molding process. Metallic inserts were surface engraved and overmolded in one-side and two-side configurations. A lap shear test was used to examine the strength of the joints. Engraved metallic surfaces and adequate imprints on polyamide side were checked by optical microscope with motorized stages, and roughness parameters were also determined. Microscopic observations made it possible to describe the grooves’ shape and to conclude that a huge recast melt was formed when the lowest laser beam speed was applied; thus, the roughness parameter Ra reached the highest value of 16.8 μm (compared to 3.5 μm obtained for the fastest laser speed). The maximum shear force was detected for a sample prepared with the lowest scanning speed (one-sides joints), and it was 883 N, while for two-sided joints, the ultimate force was 1410 N (for a scanning speed of 200 mm/s).

scholarly journals Vibration and Sound Response of Glass-Fiber-Reinforced Polyamide 6 Using Microcellular-Foaming-Process-Applied Injection Molding Process

Polymers ◽  
2022 ◽  
Vol 14 (1) ◽  
pp. 173
Author(s):  
Hyun Keun Kim ◽  
Jaehoo Kim ◽  
Donghwi Kim ◽  
Youngjae Ryu ◽  
Sung Woon Cha
Keyword(s):  
Injection Molding ◽  
Glass Fiber ◽  
Natural Frequency ◽  
Damping Ratio ◽  
Polyamide 6 ◽  
Injection Molding Process ◽  
Molding Process ◽  
Response Characteristics ◽  
Foaming Process ◽  
Microcellular Foaming

In this study, the vibration and sound response characteristics of composites produced via injection molding applied with a microcellular foaming process (MCPs) were improved. The study was conducted using PA6 and glass fiber composites, which are representative thermoplastic engineering plastics. Two types of specimens were used: a plate specimen to confirm the basic sound and vibration characteristics, and a large roof-rack specimen from an actual vehicle with a complex shape. The frequency response function curve was calculated by conducting an impact test, and natural frequency and damping ratio were measured based on the curve. The results confirmed that, in the case of a specimen manufactured through the injection molding process to which MCPs were applied, the natural frequency was lowered, and the damping ratio decreased. The degree of change in the natural frequency and damping ratio was confirmed. To determine the cause of the change in the natural frequency and damping ratio, the mode shape at the natural frequency of each specimen was measured and the relationship was confirmed by measuring the density and the elastic modulus of the composite. In addition, the usability of the specimens to which MCPs were applied was verified by conducting impact strength and tensile strength tests.

scholarly journals Shrinkage and Warpage Minimization of Glass-Fiber-Reinforced Polyamide 6 Parts by Microcellular Foam Injection Molding

Polymers ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 889 ◽  
Author(s):  
Youngjae Ryu ◽  
Joo Seong Sohn ◽  
Chang-Seok Yun ◽  
Sung Woon Cha
Keyword(s):  
Injection Molding ◽  
Polyamide 6 ◽  
Injection Molding Process ◽  
Microcellular Foam ◽  
Molding Process ◽  
Glass Fiber Reinforced ◽  
Molded Parts ◽  
Injection Molded ◽  
Process Factors ◽  
Foam Injection Molding

Shrinkage and warpage of injection-molded parts can be minimized by applying microcellular foaming technology to the injection molding process. However, unlike the conventional injection molding process, the optimal conditions of the microcellular foam injection molding process are elusive because of core differences such as gas injection. Therefore, this study aims to derive process conditions to minimize the shrinkage and warpage of microcellular foam injection-molded parts made of glass fiber reinforced polyamide 6 (PA6/GF). Process factors and levels were first determined, with experiments planned accordingly. We simulated designed experiments using injection molding analysis software, and the results were analyzed using the Taguchi method, analysis of variance (ANOVA), and response surface methodology (RSM), with the ANOVA analysis being ultimately demonstrating the influence of the factors. We derived and verified the optimal combination of process factors and levels for minimizing both shrinkage and warpage using the Taguchi method and RSM. In addition, the mechanical properties and cell morphology of PA6/GF, which change with microcellular foam injection molding, were confirmed.

scholarly journals Investigations of polyamide nano-composites containing bentonite and organo-modified clays: Mechanical, thermal, structural and processing performances

2021 ◽  
Vol 60 (1) ◽  
pp. 293-302
Author(s):  
Alinda Oyku Akar ◽  
Umit Hakan Yildiz ◽  
Umit Tayfun
Keyword(s):  
Mechanical Test ◽  
Thermal Studies ◽  
Polyamide 6 ◽  
Injection Molding Process ◽  
Gravimetric Analysis ◽  
Molding Process ◽  
Scanning Calorimetry ◽  
Modified Clays ◽  
Blending Method ◽  
Activated Bentonite

Abstract Polyamide 6 (PA) matrix was reinforced with Na-activated bentonite, amino functional silane treated bentonite and organo-modified clays at different concentrations. The preparation of composites was carried out using melt-blending method and the test samples were prepared by injection-molding process. Mechanical, thermal, structural and processing investigations of PA based composites were reported performing via tensile, hardness, and impact tests, differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction analysis (XRD) and force measurements, respectively. According to mechanical test results, additions of fillers to PA matrix caused slight improvements for tensile strength and modulus parameters. Silane treated BNT exhibited improvement in mechanical results compared to Na-activated bentonite additions. Thermal studies revealed that decomposition and melting temperatures of PA shifted to higher values after inclusion of clay into polymer matrix. Results confirmed that organo-clay and bentonite additions with their lower filling ratios yielded enhancements for the mechanical and thermal performance of polyamide.

Filling Behavior of Polymer Material into Sub-^|^mu;m Structure in Injection Molding Process

2013 ◽  
Vol 133 (4) ◽  
pp. 105-111
Author(s):  
Chisato Yoshimura ◽  
Hiroyuki Hosokawa ◽  
Koji Shimojima ◽  
Fumihiro Itoigawa
Keyword(s):  
Injection Molding ◽  
Polymer Material ◽  
Injection Molding Process ◽  
Molding Process

Pengembangan Mesin Pencacah Sampah/Limbah Plastik Dengan Sistem Crusher dan Silinder Pemotong Tipe Reel

2015 ◽  
Vol 10 (2) ◽  
pp. 66
Author(s):  
Junaidi - ◽  
Ichlas Nur ◽  
Nofriadi - ◽  
Rusmardi -
Keyword(s):  
Testing Machine ◽  
Engine Performance ◽  
Performance Testing ◽  
Injection Molding Process ◽  
Molding Process ◽  
Recycling Industry ◽  
Performance Improvements ◽  
Plastic Recycling ◽  
Technical Evaluation ◽  
Lower Frame

Waste plastic mounting, but can be recycled into other products in the form of granules before further processed into pellets and seed injection molding process produces products such as buckets, plates, bottles and other beverages. To be processed into the required form of granules of plastic thrasher. Though so small plastic recycling industry is still constrained in plastic enumeration process because the machine used was not optimal ability. The purpose of this research is the development of the system thrasher plastic crusher and cutter cylinder-type reel and technical evaluation. This study was conducted over two years, the first year the design and manufacture of machinery, the second year is a technical evaluation of the engine, engine performance improvements and economic analysis of granular plastic products.From the results obtained engine design capacity of the machine ± 350 kg / h, the engine size is 50 cm x 120 cm x 30 cm, power motor of 10 HP at 1450 RPM rotation with 3 phase. Some of the major components of the engine that is, counter crusher unit consists of two counter rotating cylinders opposite, counter shaft size Ø 4 cm x 58 cm, blade chopper Ø 17 cm x 2 cm with the number of teeth / blades 7 pieces and the number of blades along shaft 7 pieces, buses retaining Ø 10 cm x 2 cm. Counter-cylinder unit consists of a reel-type cutter counter shaft size Ø 4 cm x 90 cm, the middle shaft mounted cylinder with Ø 17 cm x 40 cm as the holder of the chopper blades. Chopper blade consists of 4 pieces with a size of 40 cm x 2 cm x 4 cm with ASSAB materials. Furthermore, as the blade retaining bedknife shear force of the blade chopper, upper frame, lower frame, strainer, funnel entry, exit funnel, and the drive unit consists of an electric motor, reducer, belts, pulleys and 2 pieces of gear transmission. The results of performance testing machine crusher round cylinder 75 RPM and 1450 RPM reel-type cutting machine capacity ± 300 kg / h on the filter hole Ø 1.5 cm, with a 80% grain uniformity.

scholarly journals Machine learning and simulation-based surrogate modeling for improved process chain operation

2021 ◽  
Author(s):  
André Hürkamp ◽  
Sebastian Gellrich ◽  
Antal Dér ◽  
Christoph Herrmann ◽  
Klaus Dröder ◽  
...  
Keyword(s):  
Surrogate Modeling ◽  
Temperature History ◽  
Injection Molding Process ◽  
Process Chain ◽  
Molding Process ◽  
Whole Process ◽  
Virtual Production ◽  
Sensor Model ◽  
Fast Prediction ◽  
Operation Phase

AbstractIn this contribution, a concept is presented that combines different simulation paradigms during the engineering phase. These methods are transferred into the operation phase by the use of data-based surrogates. As an virtual production scenario, the process combination of thermoforming continuous fiber-reinforced thermoplastic sheets and injection overmolding of thermoplastic polymers is investigated. Since this process is very sensitive regarding the temperature, the volatile transfer time is considered in a dynamic process chain control. Based on numerical analyses of the injection molding process, a surrogate model is developed. It enables a fast prediction of the product quality based on the temperature history. The physical model is transferred to an agent-based process chain simulation identifying lead time, bottle necks and quality rates taking into account the whole process chain. In the second step of surrogate modeling, a feasible soft sensor model is derived for quality control over the process chain during the operation stage. For this specific uses case, the production rejection can be reduced by 12% compared to conventional static approaches.

scholarly journals Study on External Gas-Assisted Mold Temperature Control with the Assistance of a Flow Focusing Device in the Injection Molding Process

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 965 ◽  
Author(s):  
Nguyen Truong Giang ◽  
Pham Son Minh ◽  
Tran Anh Son ◽  
Tran Minh The Uyen ◽  
Thanh-Hai Nguyen ◽  
...  
Keyword(s):  
Injection Molding ◽  
Temperature Control ◽  
Mold Temperature ◽  
Injection Molding Process ◽  
Melt Flow ◽  
Flow Focusing ◽  
Molding Process ◽  
Heating Efficiency ◽  
Flow Length ◽  
Insert Plate

In the injection molding field, the flow of plastic material is one of the most important issues, especially regarding the ability of melted plastic to fill the thin walls of products. To improve the melt flow length, a high mold temperature was applied with pre-heating of the cavity surface. In this paper, we present our research on the injection molding process with pre-heating by external gas-assisted mold temperature control. After this, we observed an improvement in the melt flow length into thin-walled products due to the high mold temperature during the filling step. In addition, to develop the heating efficiency, a flow focusing device (FFD) was applied and verified. The simulations and experiments were carried out within an air temperature of 400 °C and heating time of 20 s to investigate a flow focusing device to assist with external gas-assisted mold temperature control (Ex-GMTC), with the application of various FFD types for the temperature distribution of the insert plate. The heating process was applied for a simple insert model with dimensions of 50 mm × 50 mm × 2 mm, in order to verify the influence of the FFD geometry on the heating result. After that, Ex-GMTC with the assistance of FFD was carried out for a mold-reading process, and the FFD influence was estimated by the mold heating result and the improvement of the melt flow length using acrylonitrile butadiene styrene (ABS). The results show that the air sprue gap (h) significantly affects the temperature of the insert and an air sprue gap of 3 mm gives the best heating rate, with the highest temperature being 321.2 °C. Likewise, the actual results show that the height of the flow focusing device (V) also influences the temperature of the insert plate and that a 5 mm high FFD gives the best results with a maximum temperature of 332.3 °C. Moreover, the heating efficiency when using FFD is always higher than without FFD. After examining the effect of FFD, its application was considered, in order to improve the melt flow length in injection molding, which increased from 38.6 to 170 mm, while the balance of the melt filling was also clearly improved.

Sign in / Sign up

Export Citation Format

Share Document