scholarly journals Binaural Modelling and Spatial Auditory Cue Analysis of 3D-Printed Ears

Sensors ◽  
2021 ◽  
Vol 21 (1) ◽  
pp. 227
Author(s):  
Te Meng Ting ◽  
Nur Syazreen Ahmad ◽  
Patrick Goh ◽  
Junita Mohamad-Saleh
Keyword(s):  
Sound Source ◽  
Elevation Angle ◽  
Three Dimensional ◽  
Estimation Method ◽  
Distance Estimation ◽  
Outdoor Environment ◽  
Average Error ◽  
Spectral Cues ◽  
Polar Coordinate ◽  
3D Printed

In this work, a binaural model resembling the human auditory system was built using a pair of three-dimensional (3D)-printed ears to localize a sound source in both vertical and horizontal directions. An analysis on the proposed model was firstly conducted to study the correlations between the spatial auditory cues and the 3D polar coordinate of the source. Apart from the estimation techniques via interaural and spectral cues, the property from the combined direct and reverberant energy decay curve is also introduced as part of the localization strategy. The preliminary analysis reveals that the latter provides a much more accurate distance estimation when compared to approximations via sound pressure level approach, but is alone not sufficient to disambiguate the front-rear confusions. For vertical localization, it is also shown that the elevation angle can be robustly encoded through the spectral notches. By analysing the strengths and shortcomings of each estimation method, a new algorithm is formulated to localize the sound source which is also further improved by cross-correlating the interaural and spectral cues. The proposed technique has been validated via a series of experiments where the sound source was randomly placed at 30 different locations in an outdoor environment up to a distance of 19 m. Based on the experimental and numerical evaluations, the localization performance has been significantly improved with an average error of 0.5 m from the distance estimation and a considerable reduction of total ambiguous points to 3.3%.

scholarly journals Generation of Beam Tilt through Three-Dimensional Printed Surface

Electronics ◽  
2021 ◽  
Vol 10 (24) ◽  
pp. 3174
Author(s):  
Sujan Shrestha ◽  
Hijab Zahra ◽  
Syed Muzahir Abbas ◽  
Arslan Kiyani ◽  
Bahare Mohamadzade ◽  
...  
Keyword(s):  
Electromagnetic Waves ◽  
Low Cost ◽  
Elevation Angle ◽  
Three Dimensional ◽  
Side Lobe ◽  
Side Lobe Level ◽  
Operating Frequency Range ◽  
Input Source ◽  
3D Printed ◽  
Ku Band

In this paper, 3D printed surfaces are presented to study this technology’s application in generating beam tilt for the electromagnetic waves in the Ku-band. Additionally, the input source is maintained by a feed horn that is additively manufactured and is coated with copper spray paint to add conductivity, which is fed by a WR-75 waveguide. The proposed beam tilt generating surface is also referred to as a Beam Deviating Surface (BDS). There is no relative gap between the BDS and the aperture of the horn, which eventually decreased the overall antenna height. The BDS layer is able to deviate the beam for a fixed elevation angle of 22.5∘ and could be consequently rotated along with the rotation of the BDS prototype. The voltage standing wave ratio value is less than two over the operating frequency range, which depicts the wideband behavior. The measured and simulated radiation patterns show that we can tilt the electromagnetic waves in ranges of up to +/−22.5∘ with a minimum side lobe level of −5 dB at frequencies from 10 to 15 GHz. This signifies the wideband characteristic of the proposed prototype, which is achieved by Vero material from Multijet Printing that is a low-cost and rapid manufacturing 3D printing technology.

scholarly journals Camera-Based System for Drafting Detection While Cycling

Sensors ◽  
2020 ◽  
Vol 20 (5) ◽  
pp. 1241 ◽  
Author(s):  
Gianni Allebosch ◽  
Simon Van den Bossche ◽  
Peter Veelaert ◽  
Wilfried Philips
Keyword(s):  
Detection System ◽  
Estimation Method ◽  
Distance Estimation ◽  
Extended Period ◽  
Ground Truth ◽  
Average Error ◽  
Test Scenario ◽  
Long Distance ◽  
Wind Resistance ◽  
Set Up

Drafting involves cycling so close behind another person that wind resistance is significantly reduced, which is illegal during most long distance and several short distance triathlon and duathlon events. In this paper, a proof of concept for a drafting detection system based on computer vision is proposed. After detecting and tracking a bicycle through the various scenes, the distance to this object is estimated through computational geometry. The probability of drafting is then determined through statistical analysis of subsequent measurements over an extended period of time. These algorithms are tested using a static recording and a recording that simulates a race situation with ground truth distances obtained from a Light Detection And Ranging (LiDAR) system. The most accurate developed distance estimation method yields an average error of 0.46 m in our test scenario. When sampling the distances at periods of 1 or 2 s, simulations demonstrate that a drafting violation is detected quickly for cyclists riding at 2 m or more below the limit, while generally avoiding false positives during the race-like test set-up and five hour race simulations.

Use of Three-dimensional Printing in the Development of Optimal Cardiac CT Scanning Protocols

2020 ◽  
Vol 16 (8) ◽  
pp. 967-977
Author(s):  
Zhonghua Sun
Keyword(s):  
Cardiovascular Disease ◽  
Cardiac Computed Tomography ◽  
Three Dimensional ◽  
Ct Scanning ◽  
Aortic Diseases ◽  
Clinical Value ◽  
Three Dimensional Printing ◽  
Doctor Patient Communication ◽  
Medical Education And Training ◽  
3D Printed

Three-dimensional (3D) printing is increasingly used in medical applications with most of the studies focusing on its applications in medical education and training, pre-surgical planning and simulation, and doctor-patient communication. An emerging area of utilising 3D printed models lies in the development of cardiac computed tomography (CT) protocols for visualisation and detection of cardiovascular disease. Specifically, 3D printed heart and cardiovascular models have shown potential value in the evaluation of coronary plaques and coronary stents, aortic diseases and detection of pulmonary embolism. This review article provides an overview of the clinical value of 3D printed models in these areas with regard to the development of optimal CT scanning protocols for both diagnostic evaluation of cardiovascular disease and reduction of radiation dose. The expected outcomes are to encourage further research towards this direction.

Investigation of the Static Behavior and Failure Mechanisms of a 3D Printed Bio-Based Sandwich with Auxetic Core

2020 ◽  
Vol 12 (05) ◽  
pp. 2050051
Author(s):  
Khawla Essassi ◽  
Jean-Luc Rebiere ◽  
Abderrahim El Mahi ◽  
Mohamed Amine Ben Souf ◽  
Anas Bouguecha ◽  
...  
Keyword(s):  
Failure Mechanisms ◽  
Three Dimensional ◽  
Acoustic Emissions ◽  
Shear Stiffness ◽  
Tensile Tests ◽  
Sandwich Composite ◽  
Static Behavior ◽  
Flax Fibers ◽  
Data Points ◽  
3D Printed

In this research contribution, the static behavior and failure mechanisms are developed for a three-dimensional (3D) printed dogbone, auxetic structure and sandwich composite using acoustic emissions (AEs). The skins, core and whole sandwich are manufactured using the same bio-based material which is polylactic acid reinforced with micro-flax fibers. Tensile tests are conducted on the skins and the core while bending tests are conducted on the sandwich composite. Those tests are carried out on four different auxetic densities in order to investigate their effect on the mechanical and damage properties of the materials. To monitor the invisible damage and damage propagation, a highly sensitive AE testing method is used. It is found that the sandwich with high core density displays advanced mechanical properties in terms of bending stiffness, shear stiffness, facing bending stress and core shear stress. In addition, the AE data points during testing present an amplitude range of 40–85[Formula: see text]dB that characterizes visible and invisible damage up to failure.

scholarly journals Effects of intracorneal ring segments implementation technique and design on corneal biomechanics and keratometry in a personalized computational analysis

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Niksa Mohammadi Bagheri ◽  
Mahmoud Kadkhodaei ◽  
Shiva Pirhadi ◽  
Peiman Mosaddegh
Keyword(s):  
Clinical Data ◽  
Three Dimensional ◽  
Element Model ◽  
Von Mises Stress ◽  
Patient Specific ◽  
Average Error ◽  
Constant Thickness ◽  
Arc Length ◽  
Implementation Techniques ◽  
Von Mises

AbstractThe implementation of intracorneal ring segments (ICRS) is one of the successfully applied refractive operations for the treatment of keratoconus (kc) progression. The different selection of ICRS types along with the surgical implementation techniques can significantly affect surgical outcomes. Thus, this study aimed to investigate the influence of ICRS implementation techniques and design on the postoperative biomechanical state and keratometry results. The clinical data of three patients with different stages and patterns of keratoconus were assessed to develop a three-dimensional (3D) patient-specific finite-element model (FEM) of the keratoconic cornea. For each patient, the exact surgery procedure definitions were interpreted in the step-by-step FEM. Then, seven surgical scenarios, including different ICRS designs (complete and incomplete segment), with two surgical implementation methods (tunnel incision and lamellar pocket cut), were simulated. The pre- and postoperative predicted results of FEM were validated with the corresponding clinical data. For the pre- and postoperative results, the average error of 0.4% and 3.7% for the mean keratometry value ($$\text {K}_{\text{mean}}$$ K mean ) were predicted. Furthermore, the difference in induced flattening effects was negligible for three ICRS types (KeraRing segment with arc-length of 355, 320, and two separate 160) of equal thickness. In contrast, the single and double progressive thickness of KeraRing 160 caused a significantly lower flattening effect compared to the same type with constant thickness. The observations indicated that the greater the segment thickness and arc-length, the lower the induced mean keratometry values. While the application of the tunnel incision method resulted in a lower $$\text {K}_{\text{mean}}$$ K mean value for moderate and advanced KC, the induced maximum Von Mises stress on the postoperative cornea exceeded the induced maximum stress on the cornea more than two to five times compared to the pocket incision and the preoperative state of the cornea. In particular, an asymmetric regional Von Mises stress on the corneal surface was generated with a progressive ICRS thickness. These findings could be an early biomechanical sign for a later corneal instability and ICRS migration. The developed methodology provided a platform to personalize ICRS refractive surgery with regard to the patient’s keratoconus stage in order to facilitate the efficiency and biomechanical stability of the surgery.

scholarly journals Midface Reconstruction: Planning and Outcome

2020 ◽  
Vol 53 (03) ◽  
pp. 324-334
Author(s):  
Gautam Biswas
Keyword(s):  
Digital Imaging ◽  
3D Structure ◽  
Three Dimensional ◽  
The Past ◽  
Complex Anatomy ◽  
Osseointegrated Implants ◽  
Low Profile ◽  
3D Printed ◽  
Midface Reconstruction ◽  
Reconstruction Planning

Abstract Reconstruction of the complex anatomy and aesthetics of the midface is often a challenge. A careful understanding of this three-dimensional (3D) structure is necessary. Anticipating the extent of excision and its planning following oncological resections is critical.In the past over two decades, with the advances in microsurgical procedures, contributions toward the reconstruction of this area have generated interest. Planning using digital imaging, 3D printed models, osseointegrated implants, and low-profile plates, has favorably impacted the outcome. However, there are still controversies in the management: to use single composite tissues versus multiple tissues; implants versus autografts; vascularized versus nonvascularized bone; prosthesis versus reconstruction.This article explores the present available options in maxillary reconstruction and outlines the approach in the management garnered from past publications and experiences.

scholarly journals Recurrent contracted sockets treated with personalized, three-dimensionally printed conformers and buccal grafts

2021 ◽  
pp. 112067212110000
Author(s):  
Annabel LW Groot ◽  
Jelmer S Remmers ◽  
Roel JHM Kloos ◽  
Peerooz Saeed ◽  
Dyonne T Hartong
Keyword(s):  
Three Dimensional ◽  
Case Series ◽  
Secondary Outcome ◽  
Retrospective Case ◽  
Upper Eyelid ◽  
Ocular Prosthesis ◽  
Buccal Mucosal Graft ◽  
Custom Made ◽  
3D Printed

Purpose: Recurrent contracted sockets are complex situations where previous surgeries have failed, disabling the wear of an ocular prosthesis. A combined method of surgery and long-term fixation using custom-made, three-dimensional (3D) printed conformers is evaluated. Methods: Retrospective case series of nine patients with recurrent excessive socket contraction and inability to wear a prosthesis, caused by chemical burns ( n = 3), fireworks ( n = 3), trauma ( n = 2) and enucleation and radiotherapy at childhood due to optic nerve glioma ( n = 1) with three average previous socket surgeries (range 2–6). Treatment consisted of a buccal mucosal graft and personalized 3D-printed conformer designed to be fixated to the periosteum and tarsal plates for minimal 2 months. Primary outcome was the retention of an ocular prosthesis. Secondary outcome was the need for additional surgeries. Results: Outcomes were measured at final follow-up between 7 and 36 months postoperatively (mean 20 months). Eight cases were able to wear an ocular prosthesis after 2 months. Three cases initially treated for only the upper or only the lower fornix needed subsequent surgery for the opposite fornix for functional reasons. Two cases had later surgery for cosmetic improvement of upper eyelid position. Despite pre-existing lid abnormalities (scar, entropion, lash deficiency), cosmetic outcome was judged highly acceptable in six cases because of symmetric contour and volume, and reasonably acceptable in the remaining two. Conclusions: Buccal mucosal transplant fixated with a personalized 3D-designed conformer enables retention of a well-fitted ocular prosthesis in previously failed socket surgeries. Initial treatment of both upper and lower fornices is recommended to avoid subsequent surgeries for functional reasons.

scholarly journals Three-dimensional printing for heart diseases: clinical application review

2021 ◽  
Author(s):  
Yanyan Ma ◽  
Peng Ding ◽  
Lanlan Li ◽  
Yang Liu ◽  
Ping Jin ◽  
...  
Keyword(s):  
3D Printing ◽  
Clinical Application ◽  
Heart Diseases ◽  
Three Dimensional ◽  
Convincing Evidence ◽  
Surgical Interventions ◽  
Three Dimensional Printing ◽  
Complex Anatomy ◽  
Precise Understanding ◽  
3D Printed

AbstractHeart diseases remain the top threat to human health, and the treatment of heart diseases changes with each passing day. Convincing evidence shows that three-dimensional (3D) printing allows for a more precise understanding of the complex anatomy associated with various heart diseases. In addition, 3D-printed models of cardiac diseases may serve as effective educational tools and for hands-on simulation of surgical interventions. We introduce examples of the clinical applications of different types of 3D printing based on specific cases and clinical application scenarios of 3D printing in treating heart diseases. We also discuss the limitations and clinically unmet needs of 3D printing in this context.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

Sign in / Sign up

Export Citation Format

Share Document