scholarly journals Enhanced LDM for Next-Generation Digital Broadcasting Transmission

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1716
Author(s):  
Xianzheng Deng ◽  
Xin Bian ◽  
Mingqi Li
Keyword(s):  
Fading Channels ◽  
Data Stream ◽  
Signal To Noise Ratio ◽  
Additive White Gaussian Noise ◽  
Core Layer ◽  
Mobile Services ◽  
Parity Check ◽  
Next Generation ◽  
Frequency Domain Multiplexing ◽  
Digital Broadcasting

In the traditional layered division multiplexing (LDM) system, by simply adjusting the injection level, the reception performance of the core layer (CL) mobile services will be decreased significantly, resulting in the deterioration of system coverage performance. Thus, it is necessary to improve the performance of the enhanced layer (EL) service reception without affecting the reception threshold of CL service. To achieve this, in this paper, an enhanced LDM (En-LDM) scheme that supports multi-service transmission is proposed for the next-generation broadcasting network. In this scheme, at the transmitter end, part of the low-density parity-check (LDPC) coded data stream of fixed service conveyed in the EL will be extracted out through puncturing, and then, it will be transmitted over the CL of the LDM signal along with the original CL data in a frequency domain multiplexing (FDM) manner. At the receiving end, the punctured data of the EL fixed service will be recovered with a higher signal-to-noise ratio (SNR). Compared to the traditional LDM scheme, the proposed En-LDM scheme can significantly improve the reception performance of fixed services without decreasing the SNR threshold of mobile services. Moreover, the En-LDM can achieve a higher channel capacity than that of the traditional LDM for both the fixed services and the overall services. The superiority of the proposed En-LDM scheme over the traditional LDM scheme is validated by the simulation under the additive white Gaussian noise (AWGN) and fading channels.

scholarly journals A Construction of High Performance Quasicyclic LDPC Codes: A Combinatoric Design Approach

2019 ◽  
Vol 2019 ◽  
pp. 1-10 ◽  
Author(s):  
Muhammad Asif ◽  
Wuyang Zhou ◽  
Muhammad Ajmal ◽  
Zain ul Abiden Akhtar ◽  
Nauman Ali Khan
Keyword(s):  
Iterative Decoding ◽  
High Performance ◽  
Linear Complexity ◽  
Signal To Noise Ratio ◽  
Additive White Gaussian Noise ◽  
Ldpc Codes ◽  
Combinatorial Designs ◽  
Parity Check ◽  
Excellent Performance ◽  
Moderate Length

This correspondence presents a construction of quasicyclic (QC) low-density parity-check (LDPC) codes based on a special type of combinatorial designs known as block disjoint difference families (BDDFs). The proposed construction of QC-LDPC codes gives parity-check matrices with column weight three and Tanner graphs having a girth lower-bounded by 6. The proposed QC-LDPC codes provide an excellent performance with iterative decoding over an additive white Gaussian-noise (AWGN) channel. Performance analysis shows that the proposed short and moderate length QC-LDPC codes perform as well as their competitors in the lower signal-to-noise ratio (SNR) region but outperform in the higher SNR region. Also, the codes constructed are quasicyclic in nature, so the encoding can be done with simple shift-register circuits with linear complexity.

scholarly journals Encrypted message transmission in a QO-STBC encoded MISO wireless Communication system under implementation of low complexity ML decoding algorithm

2012 ◽  
Vol 2 (2) ◽  
pp. 53-58
Author(s):  
Shaikh Enayet Ullah ◽  
Md. Golam Rashed ◽  
Most. Farjana Sharmin
Keyword(s):  
Fading Channels ◽  
Gaussian Noise ◽  
Communication System ◽  
Channel Coding ◽  
Signal To Noise Ratio ◽  
Additive White Gaussian Noise ◽  
Text Message ◽  
Low Complexity ◽  
White Gaussian Noise ◽  
Message Transmission

In this paper, we made a comprehensive BER simulation study of a quasi- orthogonal space time block encoded (QO-STBC) multiple-input single output(MISO) system. The communication system under investigation has incorporated four digital modulations (QPSK, QAM, 16PSK and 16QAM) over an Additative White Gaussian Noise (AWGN) and Raleigh fading channels for three transmit and one receive antennas. In its FEC channel coding section, three schemes such as Cyclic, Reed-Solomon and ½-rated convolutionally encoding have been used. Under implementation of merely low complexity ML decoding based channel estimation and RSA cryptographic encoding /decoding algorithms, it is observable from conducted simulation test on encrypted text message transmission that the communication system with QAM digital modulation and ½-rated convolutionally encoding techniques is highly effective to combat inherent interferences under Raleigh fading and additive white Gaussian noise (AWGN) channels. It is also noticeable from the study that the retrieving performance of the communication system degrades with the lowering of the signal to noise ratio (SNR) and increasing in order of modulation.

scholarly journals RESEARCH OF CHARACTERISTICS OF NOISE IMMUNITY WITH USE OF ORTHOGONAL CODING

2018 ◽  
pp. 80-85 ◽  
Author(s):  
A. V. Rabin ◽  
M. A. Dobroselskij ◽  
V. A. Lipatnikov
Keyword(s):  
Fading Channels ◽  
Communication Systems ◽  
Signal To Noise Ratio ◽  
Additive White Gaussian Noise ◽  
Digital Signals ◽  
Coding Gain ◽  
Convolutional Coding ◽  
Orthogonal Codes ◽  
Effective Use ◽  
Digital Communication Systems

In the digital communication systems for noise immunity's increase with the fixed code rate it is proposed to use an additional orthogonal coding developed by the authors. It is an analogue of convolutional coding over the rational numbers' field. Transmission of digital signals in Additive white Gaussian noise (AWGN) channel and fading channels is considered including a joint use of the orthogonal and correcting codes (block and convolutional). It is shown that losses in signal-to-noise ratio can be significantly reduced by use of orthogonal coding. By increase of matrices' order, on which basis orthogonal codes are constructed, the coding gain grows also. By use of the proposed by the authors orthogonal coding the required quality of communication is implemented with a smaller energy cost. The significant coding gain (up to 6,4 dB in the channels with the AWGN, up to 22,74 dB in the fading channels) provided by more effective use of energy of transmitted signals is reached without increase in complexity and cost of transmitting/receiving devices.

Performance Comparison between DPSK and OQPSK modulation approaches in multi environments channels with Matlab Simulink models

2019 ◽  
Vol 7 (1) ◽  
pp. 30-39
Author(s):  
Fatima faydhe Al- Azzawi ◽  
Faeza Abas Abid ◽  
Zainab faydhe Al-Azzawi
Keyword(s):  
Phase Shift ◽  
Fading Channels ◽  
Additive White Gaussian Noise ◽  
Block Codes ◽  
Performance Comparison ◽  
Phase Shift Keying ◽  
Differential Phase Shift ◽  
Matlab Simulink ◽  
Communication Industry ◽  
Shift Keying

Phase shift keying modulation approaches are widely used in the communication industry. Differential phase shift keying (DPSK) and Offset Quadrature phase shift keying (OQPSK) schemes are chosen to be investigated is multi environment channels, where both systems are designed using MATLAB Simulink and tested. Cross talk and unity of signals generated from DPSK and OQPSK are examined using Cross-correlation and auto-correlation, respectively. In this research a proposed system included improvement in bit error rate (BER) of both systems in  the additive white Gaussian Noise (AWGN) channel, by using the convolutional and block codes, by increasing the ratio of energy in the specular component to the energy in the diffuse component (k) and  the diversity order BER in the fading channels will be improved in both systems.    

scholarly journals On the Performance Analysis of Switched Diversity Combining Receivers over Fisher–Snedecor ℱ Composite Fading Channels

Sensors ◽  
2021 ◽  
Vol 21 (9) ◽  
pp. 3014
Author(s):  
Weijun Cheng ◽  
Xiaoting Wang ◽  
Tengfei Ma ◽  
Gang Wang
Keyword(s):  
Fading Channels ◽  
Error Probability ◽  
Signal To Noise Ratio ◽  
Multipath Fading ◽  
Performance Criteria ◽  
Statistical Characteristics ◽  
Diversity Combining ◽  
Systematic Analysis ◽  
Average Bit Error Probability ◽  
Switched Diversity Combining

In some emerging wireless applications, such as wearable communication and low-power sensor network applications, wireless devices or nodes not only require simple physical implementation approaches but also require certain reliable receiver techniques to overcome the effects of multipath or shadowed fading. Switched diversity combining (SDC) systems could be a simple and promising solution to the above requirements. Recently, a Fisher–Snedecor ℱ composited fading model has gained much interest because of its modeling accuracy and calculation tractability. However, the performance of SDC systems over ℱ fading channels has not yet been analyzed in the open literature. To this end, this paper presents a systematic analysis of SDC systems over ℱ fading channels, including dual-branch switch-and-stay combining (SSC), multibranch switch-and examine combining (SEC), and SEC with post-examining selection (SECps) systems. We first investigate the statistical characteristics of univariate and bivariate ℱ distributions. Then, these statistical expressions are introduced into the above SDC systems and the statistical metrics of the output signal-to-noise ratio (SNR) for these systems are deduced in different ℱ fading scenarios. Thirdly, certain exact and novel expressions of performance criteria, such as the outage probability, the average bit error probability and average symbol error probability, as well as the average channel capacity for SSC, SEC, and SECps are derived. To find the optimum performance, optimal analysis is performed for the independent and identically distributed cases. Finally, numerical evaluation and simulations are carried out to demonstrate the validity of the theoretical analysis under various ℱ fading scenarios. According to the obtained results, the multipath fading parameter has more influence on the performance of SDC systems than the shadowing parameter, the correlation coefficient, or the average SNR. Importantly, the SDC systems can provide switched diversity gains only when the switching threshold is not too large or too small compared to the average SNR.

scholarly journals Identification and authentication for wireless transmission security based on RF-DNA fingerprint

2019 ◽  
Vol 2019 (1) ◽  
Author(s):  
Xueli Wang ◽  
Yufeng Zhang ◽  
Hongxin Zhang ◽  
Xiaofeng Wei ◽  
Guangyuan Wang
Keyword(s):  
Radio Frequency ◽  
Classification Accuracy ◽  
Signal To Noise Ratio ◽  
Additive White Gaussian Noise ◽  
Wireless Transmission ◽  
Dna Fingerprint ◽  
Support Vector ◽  
Multiple Discriminant Analysis ◽  
Security Issue ◽  
Rf Devices

Abstract For wireless transmission, radio-frequency device anti-cloning has become a major security issue. Radio-frequency distinct native attribute (RF-DNA) fingerprint is a developing technology to find the difference among RF devices and identify them. Comparing with previous research, (1) this paper proposed that mean (μ) feature should be added into RF-DNA fingerprint. Thus, totally four statistics (mean, standard deviation, skewness, and kurtosis) were calculated on instantaneous amplitude, phase, and frequency generated by Hilbert transform. (2) We first proposed using the logistic regression (LR) and support vector machine (SVM) to recognize such extracted fingerprint at different signal-to-noise ratio (SNR) environment. We compared their performance with traditional multiple discriminant analysis (MDA). (3) In addition, this paper also proposed to extract three sub-features (amplitude, phase, and frequency) separately to recognize extracted fingerprint under MDA. In order to make our results more universal, additive white Gaussian noise was adopted to simulate the real environment. The results show that (1) mean feature conducts an improvement in the classification accuracy, especially in low SNR environment. (2) MDA and SVM could successfully identify these RF devices, and the classification accuracy could reach 94%. Although the classification accuracy of LR is 89.2%, it could get the probability of each class. After adding a different noise, the recognition accuracy is more than 80% when SNR≥5 dB using MDA or SVM. (3) Frequency feature has more discriminant information. Phase and amplitude play an auxiliary but also pivotal role in classification recognition.

Measurement and Simulation of System Performance of Digital Broadcasting System

2013 ◽  
Vol 284-287 ◽  
pp. 2908-2912
Author(s):  
Hsien Wei Tseng ◽  
Wei Chien ◽  
Shih Nan Lu ◽  
Wei Chen Lee ◽  
Yih Guang Jan ◽  
...  
Keyword(s):  
System Performance ◽  
Simulation Analysis ◽  
Convolutional Code ◽  
Additive White Gaussian Noise ◽  
Viterbi Decoding ◽  
Modulation Formats ◽  
Reed Solomon Code ◽  
Broadcasting System ◽  
Digital Broadcasting ◽  
Transmitted Signal

In this paper, we use MATLAB software to build the physical layer transceiver of the Digital Video Broadcasting Terrestrial System (DVB-T) and Additive White Gaussian Noise (AWGN) is added into the transmitted signal during its transmission. The transmitted signal passes through modulation, demodulation, encoding and decoding processes the resulting demodulated signal is compared with the transmitted signal to calculate its Bit Error Rate (BER). Three modulation formats, QPAK, 16-QAM and 64-QAM are simulated and through various Signal to Noise (SNR) ratio to evaluate the system performance. Various encoding techniques such as Reed Solomon Code, Convolutional Code and Viterbi Decoding [1-6] have been implemented and through simulation to make detailed system performance analysis and comparison. detailed system performance simulation, analysis and comparisons.

Dual-Hop Amplify-and-Forward Variable Gain Relaying over Mixture Gamma Fading Channels

2015 ◽  
Vol 719-720 ◽  
pp. 767-772
Author(s):  
Wei Jun Cheng
Keyword(s):  
Fading Channels ◽  
Signal To Noise Ratio ◽  
Symbol Error Rate ◽  
Amplify And Forward ◽  
Variable Gain ◽  
Average Symbol Error Rate ◽  
Simulation Results ◽  
End To End ◽  
The Moment ◽  
Relaying System

In this paper, we present the end-to-end performance of a dual-hop amplify-and-forward variablegain relaying system over Mixture Gamma distribution. Novel closed-form expressions for the probability density function and the moment-generation function of the end-to-end Signal-to-noise ratio (SNR) are derived. Moreover, the average symbol error rate, the average SNR and the average capacity are found based on the above new expressions, respectively. These expressions are more simple and accuracy than the previous ones obtained by using generalized-K (KG) distribution. Finally, numerical and simulation results are shown to verify the accuracy of the analytical results.

scholarly journals MIMO Self-Encoded Spread Spectrum with Iterative Detection over Rayleigh Fading Channels

2010 ◽  
Vol 2010 ◽  
pp. 1-9 ◽  
Author(s):  
Shichuan Ma ◽  
Lim Nguyen ◽  
Won Mee Jang ◽  
Yaoqing (Lamar) Yang
Keyword(s):  
Fading Channels ◽  
Spread Spectrum ◽  
Rayleigh Fading ◽  
Mimo Systems ◽  
Signal To Noise Ratio ◽  
Multiple Input Multiple Output ◽  
Spatial Diversity ◽  
Iterative Detection ◽  
Channel Fading ◽  
Input Multiple Output

Self-encoded spread spectrum (SESS) is a novel communication technique that derives its spreading code from the randomness of the source stream rather than using conventional pseudorandom noise (PN) code. In this paper, we propose to incorporate SESS in multiple-input multiple-output (MIMO) systems as a means to combat against fading effects in wireless channels. Orthogonal space-time block-coded MIMO technique is employed to achieve spatial diversity, and the inherent temporal diversity in SESS modulation is exploited with iterative detection. Simulation results demonstrate that MIMO-SESS can effectively mitigate the channel fading effect such that the system can achieve a bit error rate of with very low signal-to-noise ratio, from 3.3 dB for a antenna configuration to just less than 0 dB for a configuration under Rayleigh fading. The performance improvement for the case is as much as 6.7 dB when compared to an MIMO PN-coded spread spectrum system.

Sign in / Sign up

Export Citation Format

Share Document