scholarly journals Novel Stable Capacitive Electrocardiogram Measurement System

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3668
Author(s):  
Chi-Chun Chen ◽  
Shu-Yu Lin ◽  
Wen-Ying Chang
Keyword(s):  
Measurement System ◽  
Input Resistance ◽  
Voltage Divider ◽  
Motion Artifact ◽  
Guard Ring ◽  
Capacitive Sensing ◽  
Ecg Signals ◽  
Optimal Input ◽  
Electrocardiogram Ecg ◽  
Mode Interference

This study presents a noncontact electrocardiogram (ECG) measurement system to replace conventional ECG electrode pads during ECG measurement. The proposed noncontact electrode design comprises a surface guard ring, the optimal input resistance, a ground guard ring, and an optimal voltage divider feedback. The surface and ground guard rings are used to reduce environmental noise. The optimal input resistor mitigates distortion caused by the input bias current, and the optimal voltage divider feedback increases the gain. Simulated gain analysis was subsequently performed to determine the most suitable parameters for the design, and the system was combined with a capacitive driven right leg circuit to reduce common-mode interference. The present study simulated actual environments in which interference is present in capacitive ECG signal measurement. Both in the case of environmental interference and motion artifact interference, relative to capacitive ECG electrodes, the proposed electrodes measured ECG signals with greater stability. In terms of R–R intervals, the measured ECG signals exhibited a 98.6% similarity to ECGs measured using contact ECG systems. The proposed noncontact ECG measurement system based on capacitive sensing is applicable for use in everyday life.

scholarly journals A Novel Adaptive Recursive Least Squares Filter to Remove the Motion Artifact in Seismocardiography

Sensors ◽  
2020 ◽  
Vol 20 (6) ◽  
pp. 1596 ◽  
Author(s):  
Shuai Yu ◽  
Sheng Liu
Keyword(s):  
Heart Rate ◽  
Least Squares ◽  
Motion Artifact ◽  
Recursive Least Squares ◽  
Detection Accuracy ◽  
Artifact Removal ◽  
Ecg Signals ◽  
The Right ◽  
Electrocardiogram Ecg ◽  
Recursive Least Squares Filter

This paper presents a novel adaptive recursive least squares filter (ARLSF) for motion artifact removal in the field of seismocardiography (SCG). This algorithm was tested with a consumer-grade accelerometer. This accelerometer was placed on the chest wall of 16 subjects whose ages ranged from 24 to 35 years. We recorded the SCG signal and the standard electrocardiogram (ECG) lead I signal by placing one electrode on the right arm (RA) and another on the left arm (LA) of the subjects. These subjects were asked to perform standing and walking movements on a treadmill. ARLSF was developed in MATLAB to process the collected SCG and ECG signals simultaneously. The SCG peaks and heart rate signals were extracted from the output of ARLSF. The results indicate a heartbeat detection accuracy of up to 98%. The heart rates estimated from SCG and ECG are similar under both standing and walking conditions. This observation shows that the proposed ARLSF could be an effective method to remove motion artifact from recorded SCG signals.

scholarly journals Adaptive Noise Filter for Real-Time Stress ECG Signal Analysis

2020 ◽  
Vol 30.8 (147) ◽  
pp. 59-64
Author(s):  
Van Manh Hoang ◽  
◽  
Manh Thang Pham
Keyword(s):  
Adaptive Filter ◽  
Stress Test ◽  
Reference Signal ◽  
Motion Artifact ◽  
Ecg Signal ◽  
Step Size ◽  
Ecg Signals ◽  
Noise Filter ◽  
Adaptive Noise ◽  
Electrocardiogram Ecg

The stress Electrocardiogram (ECG) gives more efficient results for the diagnosis of cardiovascular diseases, which may not be apparent when the patients are at rest. However, the noise produced by the movement of the patient and the environment often contaminates the ECG signal. Motion artifact is the most prevalent and difficult type of interference to filter in stress test ECG. It corrupts the quality of the desired signal thus reducing the reliability of the stress test. In this work, we first describe a quantitative study of adaptive filtering for processing the stress ECG signals. The proposed method uses the motion information obtained from a 3-axis accelerometer as a noise reference signal for the adaptive filter and the optimal weight of the adaptive filter is adjusted by the Modified Error Data Normalized Step-Size (MEDNSS) algorithm. Finally, the performance of the proposed algorithm is tested on the stress ECG signal from the subject.

Removal of ECG Baseline Wander Using a Resting Cycle Template

2021 ◽  
Vol 10 (1) ◽  
pp. 45
Author(s):  
Eladio Altamira-Colado ◽  
Miguel Bravo-Zanoguera ◽  
Daniel Cuevas-González ◽  
Marco Reyna-Carranza ◽  
Roberto López-Avitia
Keyword(s):  
Spline Interpolation ◽  
Motion Artifact ◽  
Motion Artifacts ◽  
New Method ◽  
Daily Activities ◽  
Pass Filter ◽  
Ecg Signals ◽  
Baseline Wander ◽  
Low Amplitude ◽  
Electrocardiogram Ecg

The development of electrocardiogram (ECG) wearable devices has increased due to its applications on ambulatory patients. ECG signals provide useful information about the heart behavior, but when daily activities are monitored, motion artifacts are introduced producing saturation of the signal, thus losing the information. The typical resolution used to record ECG signals is of maximum 16-bit, which might not be enough to detect low-amplitude potentials and at the same time avoid saturation due to baseline wander, since this last issue demands a low-gain signal chain. A high-resolution provides a more detailed ECG signal under a low gain input, and if the signal is corrupted by motion artifact noise but is not saturated, it can be filtered to recover the signal of interest. In this work, a 24-bit ADC is used to record the ECG, and a new method, the rest ECG cycle template, is proposed to remove the baseline wander. This new method is compared to high-pass filter and spline interpolation methods in their ability to remove baseline wander. This new method presumes that a user is able to establish a rest ECG during his/her daily activities.

scholarly journals Differential effects of the blood pressure state on pulse rate variability and heart rate variability in critically ill patients

2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Elisa Mejía-Mejía ◽  
James M. May ◽  
Mohamed Elgendi ◽  
Panayiotis A. Kyriacou
Keyword(s):  
Blood Pressure ◽  
Heart Rate ◽  
Heart Rate Variability ◽  
Pulse Rate ◽  
Pulse Transit Time ◽  
Pulse Rate Variability ◽  
Physiological Factors ◽  
Ecg Signals ◽  
Non Invasive ◽  
Electrocardiogram Ecg

AbstractHeart rate variability (HRV) utilizes the electrocardiogram (ECG) and has been widely studied as a non-invasive indicator of cardiac autonomic activity. Pulse rate variability (PRV) utilizes photoplethysmography (PPG) and recently has been used as a surrogate for HRV. Several studies have found that PRV is not entirely valid as an estimation of HRV and that several physiological factors, including the pulse transit time (PTT) and blood pressure (BP) changes, may affect PRV differently than HRV. This study aimed to assess the relationship between PRV and HRV under different BP states: hypotension, normotension, and hypertension. Using the MIMIC III database, 5 min segments of PPG and ECG signals were used to extract PRV and HRV, respectively. Several time-domain, frequency-domain, and nonlinear indices were obtained from these signals. Bland–Altman analysis, correlation analysis, and Friedman rank sum tests were used to compare HRV and PRV in each state, and PRV and HRV indices were compared among BP states using Kruskal–Wallis tests. The findings indicated that there were differences between PRV and HRV, especially in short-term and nonlinear indices, and although PRV and HRV were altered in a similar manner when there was a change in BP, PRV seemed to be more sensitive to these changes.

scholarly journals A new wearable multichannel magnetocardiogram system with a SERF atomic magnetometer array

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yanfei Yang ◽  
Mingzhu Xu ◽  
Aimin Liang ◽  
Yan Yin ◽  
Xin Ma ◽  
...  
Keyword(s):  
Independent Component Analysis ◽  
Data Acquisition ◽  
Current Distribution ◽  
Spin Exchange ◽  
Healthy Human ◽  
Ecg Signals ◽  
Mode Decomposition ◽  
Magnetometer Array ◽  
Data Acquisition And Processing ◽  
Electrocardiogram Ecg

AbstractIn this study, a wearable multichannel human magnetocardiogram (MCG) system based on a spin exchange relaxation-free regime (SERF) magnetometer array is developed. The MCG system consists of a magnetically shielded device, a wearable SERF magnetometer array, and a computer for data acquisition and processing. Multichannel MCG signals from a healthy human are successfully recorded simultaneously. Independent component analysis (ICA) and empirical mode decomposition (EMD) are used to denoise MCG data. MCG imaging is realized to visualize the magnetic and current distribution around the heart. The validity of the MCG signals detected by the system is verified by electrocardiogram (ECG) signals obtained at the same position, and similar features and intervals of cardiac signal waveform appear on both MCG and ECG. Experiments show that our wearable MCG system is reliable for detecting MCG signals and can provide cardiac electromagnetic activity imaging.

scholarly journals Data Independent Acquisition Based Bi-Directional Deep Networks for Biometric ECG Authentication

2021 ◽  
Vol 11 (3) ◽  
pp. 1125
Author(s):  
Htet Myet Lynn ◽  
Pankoo Kim ◽  
Sung Bum Pan
Keyword(s):  
Short Term Memory ◽  
Feature Learning ◽  
Biometric Authentication ◽  
Qrs Complex ◽  
Data Types ◽  
Ecg Signals ◽  
Data Independent Acquisition ◽  
Deep Networks ◽  
Classification Tasks ◽  
Electrocardiogram Ecg

In this report, the study of non-fiducial based approaches for Electrocardiogram(ECG) biometric authentication is examined, and several excessive techniques are proposed to perform comparative experiments for evaluating the best possible approach for all the classification tasks. Non-fiducial methods are designed to extract the discriminative information of a signal without annotating fiducial points. However, this process requires peak detection to identify a heartbeat signal. Based on recent studies that usually rely on heartbeat segmentation, QRS detection is required, and the process can be complicated for ECG signals for which the QRS complex is absent. Thus, many studies only conduct biometric authentication tasks on ECG signals with QRS complexes, and are hindered by similar limitations. To overcome this issue, we proposed a data-independent acquisition method to facilitate highly generalizable signal processing and feature learning processes. This is achieved by enhancing random segmentation to avoid complicated fiducial feature extraction, along with auto-correlation to eliminate the phase difference due to random segmentation. Subsequently, a bidirectional recurrent neural network (RNN) with long short-term memory (LSTM) deep networks is utilized to automatically learn the features associated with the signal and to perform an authentication task. The experimental results suggest that the proposed data-independent approach using a BLSTM network achieves a relatively high classification accuracy for every dataset relative to the compared techniques. Moreover, it exhibited a significantly higher accuracy rate in experiments using ECG signals without the QRS complex. The results also revealed that data-dependent methods can only perform well for specified data types and amendments of data variations, whereas the presented approach can also be considered for generalization to other quasi-periodical biometric signal-based classification tasks in future studies.

scholarly journals ECG Beats Classification Using Mixture of Features

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Manab Kumar Das ◽  
Samit Ari
Keyword(s):  
Feature Extraction ◽  
Extraction Methods ◽  
Ectopic Beat ◽  
Extraction Techniques ◽  
Efficient System ◽  
Ecg Signals ◽  
Temporal Features ◽  
S Transform ◽  
Electrocardiogram Ecg

Classification of electrocardiogram (ECG) signals plays an important role in clinical diagnosis of heart disease. This paper proposes the design of an efficient system for classification of the normal beat (N), ventricular ectopic beat (V), supraventricular ectopic beat (S), fusion beat (F), and unknown beat (Q) using a mixture of features. In this paper, two different feature extraction methods are proposed for classification of ECG beats: (i) S-transform based features along with temporal features and (ii) mixture of ST and WT based features along with temporal features. The extracted feature set is independently classified using multilayer perceptron neural network (MLPNN). The performances are evaluated on several normal and abnormal ECG signals from 44 recordings of the MIT-BIH arrhythmia database. In this work, the performances of three feature extraction techniques with MLP-NN classifier are compared using five classes of ECG beat recommended by AAMI (Association for the Advancement of Medical Instrumentation) standards. The average sensitivity performances of the proposed feature extraction technique for N, S, F, V, and Q are 95.70%, 78.05%, 49.60%, 89.68%, and 33.89%, respectively. The experimental results demonstrate that the proposed feature extraction techniques show better performances compared to other existing features extraction techniques.

ARRHYTHMIA DIAGNOSIS FROM ECG SIGNAL ANALYSIS USING STATISTICAL FEATURES AND NOVEL CLASSIFICATION METHOD

2021 ◽  
pp. 2150025
Author(s):  
SAURAV MANDAL ◽  
NABANITA SINHA
Keyword(s):  
Cardiac Arrhythmia ◽  
Present Model ◽  
Fluctuation Analysis ◽  
Statistical Features ◽  
Multifractal Detrended Fluctuation Analysis ◽  
Ecg Signals ◽  
Proposed Model ◽  
Electrocardiogram Ecg ◽  
Detrended Fluctuation ◽  
Heart Condition

This study aims to present an efficient model for autodetection of cardiac arrhythmia by the diagnosis of self-affinity and identification of governing processes of a number of Electrocardiogram (ECG) signals taken from MIT-BIH database. In this work, the proposed model includes statistical methods to find the diagnosis pattern for detecting cardiac abnormalities which is useful for the computer aided system for arrhythmia detection. First, the Rescale Range (R/S) analysis has been employed for ECG signals to understand the scaling property of ECG signals. The value of Hurst exponent identifies the presence of abnormality in ECG signals taken for consideration with 92.58% accuracy. In this study, Higuchi method which deals with unifractality or monofractality of signals has been applied and it is found that unifractality is sufficient to detect arrhythmia with 91.61% accuracy. The Multifractal Detrended Fluctuation Analysis (MFDFA) has been used over the present signals to identify and confirm the multifractality. The nature of multifractality is different for arrhythmia patients and normal heart condition. The multifractal analysis is useful to detect abnormalities with 93.75% accuracy. Finally, the autocorrelation analysis has been used to identify the prevalent governing process in the present arrhythmic ECG signals and study confirms that all the signals are governed by stationary autoregressive methods of certain orders. In order to increase the overall efficiency, this present model deals with analyzing all the statistical features extracted from different statistical techniques for a large number of ECG signals of normal and abnormal heart condition. Finally, the result of present analysis altogether possibly indicates that the proposed model is efficient to detect cardiac arrhythmia with 99.3% accuracy.

Arrhythmia and Normal Identification of Electrocardiogram (ECG) Signals

2020 ◽  
Author(s):  
Prihatin Oktivasari ◽  
S Imam ◽  
Riandini ◽  
Amy Hamidah Salman ◽  
Freddy Haryanto ◽  
...  
Keyword(s):  
Ecg Signals ◽  
Electrocardiogram Ecg
Sign in / Sign up

Export Citation Format

Share Document