scholarly journals Horizontal Alignment Security Design Theory and Application of Superhighways

2020 ◽  
Vol 12 (6) ◽  
pp. 2222 ◽  
Author(s):  
Yu-Long Pei ◽  
Yong-Ming He ◽  
Bin Ran ◽  
Jia Kang ◽  
Yu-Ting Song
Keyword(s):  
Design Theory ◽  
Construction Technology ◽  
Security Design ◽  
Operating Characteristics ◽  
Highway Design ◽  
Vehicle Performance ◽  
Horizontal Alignment ◽  
Road Design ◽  
Design Speed ◽  
Circular Curves

In China, the maximum design speed of highways is 120 km/h, which first appeared in the Highway Engineering Technical Standard (Trial) in 1951. However, vehicle performance, road design, and construction technology have been greatly improved over the past 68 years. To adapt to the development demands of highway design speeds above 120 km/h in the future, it is urgent to study superhighway alignment design theory. Therefore, the horizontal alignment security design theory of superhighways was developed in this paper. First, the definition, classification, and construction mode of a superhighway and suitable vehicles of different grades are presented. Then, the lengths of straight lines were limited to reduce driving fatigue. Next, the minimum radii of circular curves were calculated based on driver characteristics and stress analysis of operating vehicles. Finally, the minimum lengths of transition curves were calculated based on the centrifugal acceleration of the operating vehicles, the travel time, and the passenger visual characteristics. The calculation and analysis results show that the superhighway linear features conform to the vehicle operating characteristics, and can ensure the safety of driving.

Safety at Curves and Road Geometry Standards in Some European Countries

1996 ◽  
Vol 1523 (1) ◽  
pp. 99-106 ◽  
Author(s):  
Thierry Brenac
Keyword(s):  
Urban Areas ◽  
National Standards ◽  
European Countries ◽  
Design Standards ◽  
The Road ◽  
Horizontal Curves ◽  
Road Design ◽  
Road Geometry ◽  
Design Speed ◽  
Curve Geometry

This paper deals with safety at horizontal curves on two-lane roads outside urban areas and the way the road design standards of different European countries account for this safety aspect. After a review of some research results, the main aspects of curve geometry and the curve's place in the horizontal alignment are analyzed. The main conclusions are that the traditional design speed approach is insufficient and that formal complementary rules in road design standards, especially to improve compatibility between successive elements of the alignment, must be introduced. If such complementary rules already exist in some national standards, they are neither frequent nor homogeneous throughout the different countries, and it seems that they are not based on sufficiently developed knowledge.

scholarly journals Calculation Method of Permanent Deformation of Asphalt Mixture Based on Interval Number

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2116
Author(s):  
Yue Xiao ◽  
Limin Tang ◽  
Jiawei Xie
Keyword(s):  
Interval Analysis ◽  
Calculation Method ◽  
Design Theory ◽  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Design Parameters ◽  
Interval Variable ◽  
Road Design ◽  
Weight Assignment ◽  
Variable Weight

There are great uncertainties in road design parameters, and the traditional point numerical calculation results cannot reflect the complexity of the actual project well. Additionally, the calculation method of road design theory based on interval analysis is more difficult in the use of uncertain design parameters. In order to simplify the calculation process of the interval parameters in the road design theory, the asphalt pavement design is taken as the analysis object, and the permanent deformation of the asphalt mixture is simplified by combining the interval analysis theory. Considering the uncertainty of the design parameters, the data with boundaries but uncertain size are expressed in intervals, and then the interval calculation formula for the permanent deformation of the asphalt mixture is derived, and the interval results are obtained. In order to avoid the dependence of interval calculation on the computer code, according to the interval calculation rule, the interval calculation method with the upper and lower end point values as point operations is proposed. In order to overcome the contradiction between interval expansion results and engineering applications, by splitting the multi-interval variable formulas, the interval variable weights are reasonably given, and the synthesis of each single interval result realizes a simplified calculation based on interval variable weight assignment. The analysis results show that the interval calculation method based on the point operation rule is accurate and reliable, and the simplified method based on the interval variable weight assignment is effective and feasible. The simplified interval calculation method proposed in this paper provides a reference for the interval application of road design theory.

Parametric Simulation of Rolling Contact Fatigue

2008 ◽  
Author(s):  
Scott M. Cummings ◽  
Patricia Schreiber ◽  
Harry M. Tournay
Keyword(s):  
Rolling Contact Fatigue ◽  
Contact Fatigue ◽  
Rolling Contact ◽  
Wear Model ◽  
Primary Methods ◽  
Vehicle Performance ◽  
Track Geometry ◽  
Advantages And Disadvantages ◽  
Defect Prevention ◽  
Design Speed

Simulations of dynamic vehicle performance were used by the Wheel Defect Prevention Research Consortium (WDPRC) to explore which track and vehicle variables affect wheel fatigue life. A NUCARS® model was used to efficiently examine the effects of a multitude of parameters including wheel/rail profiles, wheel/rail lubrication, truck type, curvature, speed, and track geometry. Results from over 1,000 simulations of a loaded 1,272 kN (286,000-pound) hopper car are summarized. Rolling contact fatigue (RCF) is one way that wheels can develop treads defects. Thermal mechanical shelling (TMS) is a subset of wheel shelling in which the heat from tread braking reduces a wheel’s fatigue resistance. RCF and TMS together are estimated to account for approximately half of the total wheel tread damage problem [1]. Other types of tread damage can result from wheel slides. The work described in this paper concerns pure RCF, without regard to temperature effects or wheel slide events. Much work has been conducted in the past decade in an attempt to model the occurrence of RCF on wheels and rails. The two primary methods that have gained popularity are shakedown theory and wear model. The choice of which model to use is somewhat dependent on the type of data available, as each model has advantages and disadvantages. The wear model was selected for use in this analysis because it can account for the effect of wear on the contacting surfaces and is easily applied to simulation data in which the creep and creep force are available. The findings of the NUCARS simulations in relation to the wear model include the following: • Degree of curvature is the single most important factor in determining the amount of RCF damage to wheels; • The use of trucks (hereafter referred to as M-976) that have met the Association of American Railroads’ (AAR) M-976 Specification with properly maintained wheel and rail profiles should produce better wheel RCF life on typical routes than standard trucks; • In most curves, the low-rail wheel of the leading wheelset in each truck is most prone to RCF damage; • While the use of flange lubricators (with or without top of rail (TOR) friction control applied equally to both rails) can be beneficial in some scenarios, it should not be considered a cure-all for wheel RCF problems, and may in fact exacerbate RCF problems for AAR M-976 trucks in some instances; • Avoiding superelevation excess (operating slower than curve design speed) provides RCF benefits for wheels in cars with standard three-piece trucks; • Small track perturbations reduce the overall RCF damage to a wheel negotiating a curve.

scholarly journals Multi-fidelity algorithms for the horizontal alignment problem in road design

2019 ◽  
Vol 52 (11) ◽  
pp. 1848-1867 ◽  
Author(s):  
Mahdi Aziz ◽  
Warren Hare ◽  
Majid Jaberipour ◽  
Yves Lucet
Keyword(s):  
Horizontal Alignment ◽  
Road Design ◽  
Alignment Problem

Driver Perception–Brake Response in Stopping Sight Distance Situations

1998 ◽  
Vol 1628 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Daniel B. Fambro ◽  
Rodger J. Koppa ◽  
Dale L. Picha ◽  
Kay Fitzpatrick
Keyword(s):  
Response Time ◽  
Performance Studies ◽  
Response Times ◽  
Highway Design ◽  
Braking Performance ◽  
Reaction Distance ◽  
State Highway ◽  
Sight Distance ◽  
Design Speed ◽  
Stopping Sight Distance

One of the most important requirements in highway design is the provision of adequate stopping sight distance at every point along the roadway. At a minimum, this sight distance should be long enough to enable a vehicle traveling at or near the design speed to stop before reaching a stationary object in its path. Stopping sight distance is the sum of two components–brake reaction distance and braking distance. Brake reaction distance is based on the vehicle’s speed and the driver’s perception–brake reaction time (PBRT). Four separate, but coordinated, driver braking performance studies measured driver perception–brake response to several different stopping sight distance situations. The results from the driver braking performance studies suggest that the mean perception–brake response time to an unexpected object scenario under controlled and open road conditions is about 1.1 s. The 95th percentile perception–brake response times for these same conditions was 2.0 s. The findings from these studies are consistent with those in the literature: that is, most drivers are capable of responding to an unexpected hazard in the roadway in 2.0 s or less. Thus, the American Association of State Highway and Transportation Officials’ perception–brake response time of 2.5 s encompasses most of the driving population and is an appropriate value for highway design.

Speeds of Cars on Horizontal Curves

1998 ◽  
Vol 1612 (1) ◽  
pp. 42-47 ◽  
Author(s):  
Vojo Andjus ◽  
Mihailo Maletin
Keyword(s):  
Free Flow ◽  
Flow Conditions ◽  
Passenger Cars ◽  
Design Standards ◽  
Rural Roads ◽  
Horizontal Curves ◽  
Road Design ◽  
Realistic Approach ◽  
Actual Design ◽  
Design Speed

Revision of existing Yugoslav road-design standards, specifically in the area of road-design speed definition, required studying driver behavior in free-flow conditions in order to define drivers’ responses to the radii of horizontal curves. A specific approach with variable design speed for horizontal curves is discussed and is supported by speed measurements on roads. The pilot research was undertaken on several test sites on Yugoslav two-lane rural roads to collect reliable speed data related to characteristics of horizontal curves. Characteristics of test sites, experimental procedures, data collected, and results of data analyses are described. It is concluded that speeds of free-flow passenger cars show good correlation with radii and that actual design policy with a constant design speed underestimates speeds in radii less than 250 m. Thus, the variable design speed concept is a more realistic approach. Further research on more test sites is recommended.

Formulation and Validation of Operating Speed-Based Design Consistency Models by Bootstrapping

1997 ◽  
Vol 1579 (1) ◽  
pp. 97-103 ◽  
Author(s):  
John McFadden ◽  
Lily Elefteriadou
Keyword(s):  
Additional Data ◽  
Original Data ◽  
Statistical Technique ◽  
Geometric Design ◽  
Operating Speed ◽  
Horizontal Alignment ◽  
Alternative Means ◽  
Design Speed ◽  
Design Consistency ◽  
Consistency Models

Current U.S. policy for designing rural two-lane highways is based on design speed to ensure consistency among consecutive highway segments. The design speed concept, however, does not ensure that a consistent alignment will be achieved. A recent FHWA-sponsored project (Horizontal Alignment Design Consistency for Rural Two-Lane Highways) led to three operating speed-based geometric design consistency models, which have not yet been validated. Traditionally, the validation of such models involves the collection of additional data. The statistical technique known as “bootstrapping” was used to formulate and validate the operating speed-based geometric design consistency models by using the existing FHWA database. Bootstrapping involves random sampling with replacement from the existing database, which becomes the population. One-half of the original data collected are used in formulating the models. The remaining half of the data are subsequently used for validation. The models resulting from bootstrapping were statistically equivalent to the models developed in the FHWA study. In addition, the model validation indicated that the bootstrapping technique used to validate the operating speed models is a viable alternative means of validation. It was concluded that bootstrapping is a very useful tool that can be exploited in many related areas in the transportation field, especially because of the large amounts of data typically required in developing and validating empirical models.

Establishing highway horizontal alignment to maximize design consistency

2007 ◽  
Vol 34 (9) ◽  
pp. 1159-1168 ◽  
Author(s):  
Said M Easa ◽  
Atif Mehmood
Keyword(s):  
Geometric Features ◽  
Trial And Error ◽  
Highway Design ◽  
Rural Highways ◽  
Physical Constraints ◽  
Horizontal Alignment ◽  
Horizontal Curves ◽  
Decision Variables ◽  
Acceleration And Deceleration ◽  
Design Consistency

Highway design consistency is one of the important criteria in selecting the geometric features of proposed or existing alignments of two-lane rural highways. Operating-speed (OS) profile models have been used to evaluate design consistency by trial and error. For a proposed new highway, however, there may be geometric and physical constraints, and selection of these elements by trial and error to achieve optimal design consistency would be difficult, if not impossible. This paper presents an optimization model that establishes highway horizontal alignment to achieve maximum design consistency based on the OS profile. The decision variables of the model include radius of horizontal curves, spiral curve lengths, length of speed-change (SC) segments, and acceleration and deceleration rates. The objective function of the model minimizes the mean OS difference or the maximum OS difference for successive geometric features along the highway section. Application examples and sensitivity analysis are presented to illustrate the capabilities of the model in evaluating improvement strategies and to ensure that the model produces sound optimum alignments. The proposed model, which complements existing optimization models that mainly address highway construction cost, should be of interest to highway practitioners and engineers.Key words: design consistency, highway, geometric, horizontal alignment, optimization modeling, speed profile.

The Freeway Energy Conservation and Emission Reduction Guarantee System Research

2012 ◽  
Vol 226-228 ◽  
pp. 2471-2475
Author(s):  
Zi Qiang Li ◽  
Zheng Li
Keyword(s):  
Energy Conservation ◽  
Energy Management ◽  
Emission Reduction ◽  
Design Theory ◽  
New Technology ◽  
Road Transport ◽  
Comprehensive Analysis ◽  
System Research ◽  
Highway Design ◽  
Guarantee System

This paper uses the latest highway design theory and method of energy conservation and emission reduction to elaborate the freeway energy conservation and emission reduction. According to this, we protocol detailed freeway energy management organization settings, staffing and framework. Then we introduce the concept of energy conservation and emission reduction and promote the application new technology, materials and equipment in the freeway design and construction stages, so as to establish a more comprehensive freeway energy conservation and emission reduction technology guarantee system, it also provides the policy guarantee in order to further the effective containment of the rising road transport energy consumption. This paper conducts a comprehensive analysis and discussion on the guarantee system of energy conservation and emission reduction through the two aspects.

Sign in / Sign up

Export Citation Format

Share Document