scholarly journals Experimentation with Flexural Properties of the Carbon Fiber Graphite Fiber and Glass Fiber Composites

2019 ◽  
Vol 8 (4) ◽  
pp. 4272-4277
Keyword(s):  
Silicon Carbide ◽  
Carbon Fiber ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Composite Plates ◽  
Bending Test ◽  
Filler Material ◽  
Flexural Properties ◽  
Graphite Fiber ◽  
Three Point Bending

In the present work the flexural properties of selected composite plates are examined. The three point bending test happens to be widely acceptable method for the evaluation of flexural properties of the composite plates because of its simple geometry and structure. In this paper the influence of filler material and thickness of laminates under three point bending load on simply supported pins are reported for selected filler material combination. Filler materials used here are Glass fiber epoxy with silicon carbide, Graphite fiber epoxy with silicon carbide and Carbon fiber epoxy with silicon carbide. Investigation is carried out as per ASTM D790 standard. The mechanical properties such as flexural strength, flexural stiffness of the composite plates were investigated and reported. This work broadly points out that the flexural strength is dependent on the thickness of the laminates and amount of the filler material of the laminated composites. It was found that Carbon fiber composite shows the superior flexural strength with 6 wt% of SiC among the specimens under study.

scholarly journals A Study of Bending Property for Glass Fiber Reinforced Thermoplastic Composite Sheets

2019 ◽  
Vol 7 (06) ◽  
Author(s):  
Mustafa Faisal Zaidan ◽  
Khudhayer J. Jadee ◽  
Salwa A. Abed
Keyword(s):  
Flexural Strength ◽  
Glass Fiber ◽  
Fiber Reinforcement ◽  
Thermoplastic Composite ◽  
Bending Test ◽  
Fiber Glass ◽  
Three Point Bending ◽  
Glass Fiber Reinforced ◽  
Glass Fiber Reinforcement ◽  
Glass Reinforcement

In this research a study of the influence of percentage for chopped fiber glass reinforcement thermoplastic sheet on the flexural strength. Hot compression method used to fabricate thermoplastic (polypropylene and polyamide) reinforced by fiber glass at different percentage (10,20,30,40) wt.%, the flexural strength test done by using three-point bending test. The results shown that for bending test the sample glass fiber reinforcement polyamide (GFRPA) and sample glass fiber reinforcement polypropylene (GFRPP), which reinforced with 40% fiber glass achieved the high magnitude of flexural strength (106.1 and 70.8) MPa respectively. While the sample polyamide (PA) and polypropylene (PP) without reinforcement show the lowest magnitude of flexural strength (59.5 and 38.4) MPa respectively.  

scholarly journals Flexural Properties of Renewable Coir Fiber Reinforced Magnesium Phosphate Cement, Considering Fiber Length

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3692 ◽  
Author(s):  
Liwen Zhang ◽  
Zuqian Jiang ◽  
Hui Wu ◽  
Wenhua Zhang ◽  
Yushan Lai ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Waste Treatment ◽  
Bending Test ◽  
Magnesium Phosphate ◽  
Flexural Properties ◽  
Coir Fiber ◽  
X Ray Diffraction ◽  
Flexural Toughness ◽  
Three Point Bending ◽  
Curing Age

Coir fiber (CF), a renewable natural plant fiber, is more competitive in improving poor toughness and crack resistance of magnesium phosphate cement (MPC) than artificial fibers, due to its slight energy consumptions and low costs in production and waste treatment. In this paper, a typical three-point bending test was carried out to study the effects of CF length on MPC flexural properties. A total of forty-two cuboid specimens were employed to investigate the flexural strength, load-deflection behavior, and flexural toughness of MPC, with CF lengths varying from 0 to 30 mm at the curing age of 7 days and 28 days. Results showed that, at both two curing ages, MPC flexural strength first increased with CF length increasing, and then deceased when CF length exceeded the threshold. However, with the increase of CF length, MPC flexural toughness increased continuously, while MPC elastic modulus displayed a decreasing trend. Additionally, Modern micro testing techniques, such as scanning electron microscope (SEM) and X-ray diffraction (XRD), were also used to study the microstructure and phase compositions of specimens for further explaining the themicroscopic mechanism.

scholarly journals Flexural Properties and Microstructure Mechanisms of Renewable Coir-Fiber-Reinforced Magnesium Phosphate Cement-Based Composite Considering Curing Ages

Polymers ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 2556
Author(s):  
Liwen Zhang ◽  
Zuqian Jiang ◽  
Wenhua Zhang ◽  
Sixue Peng ◽  
Pengfei Chen
Keyword(s):  
Flexural Strength ◽  
Waste Treatment ◽  
Bending Test ◽  
Magnesium Phosphate ◽  
Flexural Properties ◽  
Coir Fiber ◽  
X Ray ◽  
Flexural Toughness ◽  
Three Point Bending ◽  
Curing Age

As a renewable natural plant fiber, Coir fiber (CF) can be used to as an alternative to improve poor toughness and crack resistance of magnesium phosphate cement (MPC), replacing such artificial fibers as steel fiber and glass fiber and thereby reducing huge energy consumptions and large costs in artificial fibers’ production and waste treatment. Aiming at examining the effects of CF volume concentrations on MPC flexural properties, this study employed a typical three-point bending test, including thirty cuboid specimens, to investigate the flexural strength, load-deflection behavior, and flexural toughness of MPC with different CF volume concentrations from 0% to 4% at the curing age of seven days and 28 days. Results demonstrated that CF presented similar effects on MPC’s properties at two curing ages. At both curing ages, as CF grew, flexural strength increased first and then decreased; specimen stiffness, i.e., MPC elastic modulus, displayed a decreasing trend; and flexural toughness was improved continuously. Additionally, modern microtesting techniques, such as, scanning electron microscopy (SEM) and energy dispersive X-ray detection (EDX), were adopted to analyze the microstructure and compositions of CF and specimens for explaining the properties microscopically.

Correlation between Process Parameters with Flexural Properties of Hybrid Glass/Jute Fibre Reinforced Epoxy Composite Fabricated via Vacuum Infusion Technique

2015 ◽  
Vol 761 ◽  
pp. 531-535
Author(s):  
Noraiham Mohamad ◽  
Mohd Fadli Hassan ◽  
Siang Yee Chang ◽  
Qumrul Ahsan ◽  
Yuhazri Yaakob ◽  
...  
Keyword(s):  
Epoxy Composite ◽  
Processing Parameters ◽  
Bending Test ◽  
Flexural Properties ◽  
Jute Fibre ◽  
Soaking Time ◽  
Three Point Bending ◽  
Vacuum Infusion ◽  
Supply Pressure ◽  
Infusion Technique

Flexural properties of hybrid glass/jute fibre reinforced epoxy composites were optimised by response surface methodology. The processing parameters of vacuum infusion technique such as supply pressure, soaking time and use of flow media were investigated. The flexural properties of the resulting composites were evaluated using three-point bending test in accordance with the ASTM D790-03 standard. The flexural strength of ~195 MPa and elastic modulus of ~13412 MPa were achieved at optimum parameter of 100 kPa pressure, 120 minutes soaking time with the utilization of flow media during vacuum infusion process.

Time-temperature superposition of flexural creep response of carbon fiber PEKK composites manufactured using different prepreg stacking sequence

2021 ◽  
pp. 089270572110517
Author(s):  
MS Irfan ◽  
RA Alia ◽  
T Khan ◽  
WJ Cantwell ◽  
R Umer
Keyword(s):  
Carbon Fiber ◽  
Master Curve ◽  
Flexural Properties ◽  
Stacking Sequence ◽  
Short Term ◽  
Creep Tests ◽  
Creep Response ◽  
Three Point Bending ◽  
Temperature Superposition ◽  
Time Temperature Superposition

In this work, the long-term creep response of high-performance carbon fiber PEKK (CF/PEKK) composites was evaluated by performing extrapolated short-term flexural creep tests at various temperatures. The time-temperature superposition principle (TTSP) with vertical as well as horizontal shifting was used to generate master curves at reference temperatures of 120°C. Satin weave-based CF/PEKK prepregs were used to manufacture eight-layer composites via compression molding, with three different stacking sequences: (a) zero-direction [0]8 (b) cross-ply [0, 90]4 and (c) quasi-isotropic [90, −45, 45, 0]2 s. The flexural properties under three-point bending arrangement in a universal testing machine were also evaluated. A dynamic mechanical thermal analyzer (DMTA) in three-point bending mode was used to evaluate the temperature-dependent viscoelastic properties of the three types of composites. The creep and creep-recovery behavior was evaluated at 40°C, 80°C, 120°C, 160°C and 200°C. To construct a master curve, extrapolated short-term isothermal creep tests were performed from 120°C to 180°C at the intervals of 10°C. The predicted master curve represents the creep behavior of composites over more than 10 years. It was shown that the quasi-isotropic CF/PEKK composites exhibited 27% and 12% higher creep resistance at 120°C as compared to zero-direction and cross-ply laminates, respectively. Higher flexural modulus (23%) and flexural strengths (33%) were also exhibited by the quasi-isotropic CF/PEKK composites. The final thickness of quasi-isotropic laminates was 8% lower than the 0o laminates. After analyzing the cross-sections of the composites, it was proposed that the superior mechanical properties of the quasi-isotropic laminates could be due to enhanced nesting between neighboring prepreg layers during the compression molding process, which resulted in closer packing of the fibers. It has been shown that the prepreg stacking sequence could affect the creep behavior and flexural properties of the compression-molded CF/PEKK composites.

scholarly journals Influence of microfillers addition on the flexural properties of carbon fiber reinforced phenolic composites

2021 ◽  
pp. 002199832110316
Author(s):  
IA Abdulganiyu ◽  
INA Oguocha ◽  
AG Odeshi
Keyword(s):  
Carbon Fiber ◽  
Flexural Strength ◽  
Carbon Fibers ◽  
Colloidal Silica ◽  
Flexural Modulus ◽  
Flexural Properties ◽  
Fiber Reinforced ◽  
Cfrp Composites ◽  
Sic Particles ◽  
Flexural Loading

The effects of microfiller addition on the flexural properties of carbon fiber reinforced phenolic (CFRP) matrix composites were investigated. The CFRP was produced using colloidal silica and silicon carbide (SiC) microfillers, 2 D woven carbon fibers, and two variants of phenolic resole (HRJ-15881 and SP-6877). The resins have the same phenol and solid content but differ in their viscosities and HCHO (formaldehyde) content. The weight fractions of microfillers incorporated into the phenolic matrix are 0.5 wt.%, 1 wt.%, 1.5 wt.%, and 2 wt.%. Flexural properties were determined using a three-point bending test and the damage evolution under flexural loading was investigated using optical and scanning electron microscopy. The results indicated that the reinforcement of phenolic resins with carbon fibers increased the flexural strength of the HRJ-15881 and SP-6877 by 508% and 909%, respectively. The flexural strength of the CFRP composites further increased with the addition of SiC particles up to 1 wt.% SiC but decreased with further increase in the amount of SiC particles. On the other hand, the flexural modulus of the CFRP composites generally decreased with the addition of SiC microfiller. Both the flexural strength and flexural modulus of the CFRP did not improve with the addition of colloidal silica particles. The decrease in flexural properties is caused by the agglomeration of the microfillers, with colloidal silica exhibiting more tendency for agglomeration than SiC. The fractured surfaces revealed fiber breakage, matrix cracking, and delamination under flexural loading. The tendency for failure worsened at microfiller addition of ≥1.5 wt.%.

Sign in / Sign up

Export Citation Format

Share Document