scholarly journals Attenuation of airborne noise by wet and dry neoprene diving hoods

Author(s):  
Gurmail S Paddan ◽  
Michael C Lower

The insertion losses of five neoprene diving hoods of varying thicknesses (2 mm–9 mm) were measured in one-third octave bands using a Kemar manikin in a diffuse broadband noise field. The insertion losses were measured in air for both dry and wet hoods. The insertion loss was calculated as the sound level in each frequency band measured with the hood, minus the corresponding sound level measured without the hood. The insertion losses were similar for both ears of the manikin. Both wet and dry hoods neither attenuated nor amplified sound below 250 Hz. Between 315 Hz–1250 Hz, the insertion loss of each hood was negative, displaying a broad resonance with a gain of 6–8 dB. In this frequency range the hood acts as a mass-spring system, resonating like a drum skin when stretched over the ears. Above 1000 Hz, the insertion loss increased with frequency (10 dB per octave), reaching a maximum of 5000 Hz–6000 Hz. Wetting each hood did not significantly affect the insertion loss; the 'drum-skin' resonance frequency was marginally lower with a wet hood, and insertion losses may be marginally greater between 1000 Hz– 10 000 Hz. The resonance frequency decreased with increasing thicknesses of hood, and the insertion loss at frequencies above the resonance increased with hood thickness.

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shuping Wang ◽  
Jiancheng Tao ◽  
Xiaojun Qiu ◽  
Ian S. Burnett

AbstractIt has been demonstrated that a staggered window achieves better noise reduction performance than a traditional single glazing one at middle to high frequencies while maintaining a degree of natural ventilation. There is, however, little improvement in the low frequency range. In contrast, this work proposes to apply coiled-up silencers consisting of coupled tubes on the side walls of staggered windows to obtain noise attenuation in a broad band, especially in the low frequency range. Each element in the silencer consists of two coupled tubes with different cross sections so that noise at more frequencies can be attenuated than that with a uniform cross section. The simulation results show that 8.8 dB overall insertion loss can be obtained between 100 and 500 Hz after applying a combination of silencers designed at 7 different frequencies, and the insertion loss of the staggered window is increased from 6.7 to 15.6 dBA between 100 and 2000 Hz for normal incident traffic noise with the proposed silencers installed. The design is validated by the experiments with a 1:4 scale down model.


Author(s):  
Pascal He´mon ◽  
Xavier Amandole`se ◽  
Franc¸oise Santi ◽  
Jan Wojciechowski

We present experimental results obtained with a deep cavity, like an Helmholtz resonator, excited by an airflow. The resonance under the action of the vortices generated in the shear layer is well described and quantified. The mounting of actuators, based on a few piezo-electric elements, allows to generate a series of two-dimensional vortices forced at a frequency which is different than the natural resonance frequency. The sound level in the cavity is strongly decreased and the broadband noise of the turbulence only remains.


NANO ◽  
2015 ◽  
Vol 10 (02) ◽  
pp. 1550024 ◽  
Author(s):  
S. Kamal Jalali ◽  
M. Hassan Naei ◽  
Nicola Maria Pugno

Application of single layered graphene sheets (SLGSs) as resonant sensors in detection of ultra-fine nanoparticles (NPs) is investigated via molecular dynamics (MD) and nonlocal elasticity approaches. To take into consideration the effect of geometric nonlinearity, nonlocality and atomic interactions between SLGSs and NPs, a nonlinear nonlocal plate model carrying an attached mass-spring system is introduced and a combination of pseudo-spectral (PS) and integral quadrature (IQ) methods is proposed to numerically determine the frequency shifts caused by the attached metal NPs. In MD simulations, interactions between carbon–carbon, metal–metal and metal–carbon atoms are described by adaptive intermolecular reactive empirical bond order (AIREBO) potential, embedded atom method (EAM), and Lennard–Jones (L–J) potential, respectively. Nonlocal small-scale parameter is calibrated by matching frequency shifts obtained by nonlocal and MD simulation approaches with same vibration amplitude. The influence of nonlinearity, nonlocality and distribution of attached NPs on frequency shifts and sensitivity of the SLGS sensors are discussed in detail.


2015 ◽  
Vol 8 (2) ◽  
pp. 179-184 ◽  
Author(s):  
Valeria Nocella ◽  
Luca Pelliccia ◽  
Paola Farinelli ◽  
Roberto Sorrentino ◽  
Mario Costa ◽  
...  

A robust and tuneless micromachined waveguide diplexer operating in the frequency range 71–86 GHz is here presented. The diplexer is based on multiple coupled cavities and it is manufactured using micromachining technology on two staked silicon layers. The diplexer consists of two filters combined to a common waveguide port via an E-plane T-junction. The two eight-order band-pass filters are centered at 73.5 and 83.5 GHz. The fractional bandwidths for two bands are 8.8 and 7.8% at higher- and lower-band, respectively. The measured insertion loss is below 0.7 dB for both the filters and the diplexer isolation is better than 55 dB, as required. The proposed technology allows for a very compact device (<20 × 20 × 1.5 mm) and the first prototypes were proved to be very robust to manufacturing tolerances and environmental tests, thus leading to an excellent tuneless manufacturing yield in future production. The diplexer will be employed in next generation terrestrial radio-link communications front-ends.


2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Venkata K. Yadalam ◽  
B. F. Feeny

A method of modal analysis by a mass-weighted proper orthogonal decomposition for multi-degree-of-freedom and distributed-parameter systems of arbitrary mass distribution is outlined. The method involves reduced-order modeling of the system mass distribution so that the discretized mass matrix dimension matches the number of sensed quantities, and hence the dimension of the response ensemble and correlation matrix. In this case, the linear interpolation of unsensed displacements is used to reduce the size of the mass matrix. The idea is applied to the modal identification of a mass-spring system and an exponential rod.


2021 ◽  
pp. 1-35
Author(s):  
Rick Dehner ◽  
Pranav Sriganesh ◽  
Ahmet Selamet ◽  
Keith Miazgowicz

Abstract The present study focuses on the acoustics of a turbocharger centrifugal compressor from a spark-ignition internal combustion engine. Whoosh noise is typically the primary concern for this type of compressor, which is loosely characterized by broadband sound elevation in the 4 to 13 kHz range. To identify the generation mechanism of broadband whoosh noise, the present study combines three approaches: three-dimensional (3D) computational fluid dynamics (CFD) predictions, experiments, and modal decomposition of 3D CFD results. After establishing the accuracy of predictions, flow structures and time-resolved pressures are closely examined in the vicinity of the main blade leading edge. This reveals the presence of rotating instabilities that may interact with the rotor blades to generate noise. An azimuthal modal decomposition is performed on the predicted pressure field to determine the number of cells and the frequency content of these rotating instabilities. The strength of the rotating instabilities and the frequency range in which noise is generated as a consequence of the rotor-rotating instability interaction, is found to correspond well with the qualitative trend of the whoosh noise that is measured several duct diameters upstream of the rotor blades. The variation of whoosh frequency range between low and high rotational speeds is interpreted through this analysis. It is also found that the whoosh noise primarily propagates along the duct as acoustic azimuthal modes. Hence, the inlet duct diameter, which governs the cut-off frequency for multi-dimensional acoustic modes, determines the lower frequency bound of the broadband noise.


1999 ◽  
Author(s):  
Mitsuteru Kimura ◽  
Katsuhisa Toshima ◽  
Harunobu Satoh

Abstract A new type all optical vibration and acceleration sensor using the combination of micromachined Si cantilever and optical fiber is proposed, and its fundamental characteristics are demonstrated. The light emitted from bulb-lens set into the V-groove is reflected at the reflector formed on the Si cantilever and then recoupled into the bulb-lens. Several sensors with different length (0.64–6.0 mm long) of the Si cantilever are fabricated to compare the theoretical resonance frequency fr obtained from the simple model and experimental ones. They had good agreement. From the sensing principle the sensing frequency range of the vibration is suitable below the fr of the Si cantilever of the sensor.


2013 ◽  
Vol 14 (5) ◽  
pp. 1228-1251 ◽  
Author(s):  
Yan Li ◽  
I-Liang Chern ◽  
Joung-Dong Kim ◽  
Xiaolin Li

AbstractWe use front tracking data structures and functions to model the dynamic evolution of fabric surface. We represent the fabric surface by a triangulated mesh with preset equilibrium side length. The stretching and wrinkling of the surface are modeled by the mass-spring system. The external driving force is added to the fabric motion through the “Impulse method” which computes the velocity of the point mass by superposition of momentum. The mass-spring system is a nonlinear ODE system. Added by the numerical and computational analysis, we show that the spring system has an upper bound of the eigen frequency. We analyzed the system by considering two spring models and we proved in one case that all eigenvalues are imaginary and there exists an upper bound for the eigen-frequency This upper bound plays an important role in determining the numerical stability and accuracy of the ODE system. Based on this analysis, we analyzed the numerical accuracy and stability of the nonlinear spring mass system for fabric surface and its tangential and normal motion. We used the fourth order Runge-Kutta method to solve the ODE system and showed that the time step is linearly dependent on the mesh size for the system.


2018 ◽  
Vol 7 (3) ◽  
pp. 31
Author(s):  
Rosa Virginia Hernández ◽  
Luis Fernando Mariño ◽  
Mawency Vergel

En este artículo se presenta la caracterización del conocimiento semántico evidenciado por un grupo de estudiantes en la representación externa a problemas de ecuaciones diferenciales lineales de segundo orden como modelos matemáticos. El trabajo fue cuantitativo de tipo exploratorio y descriptivo utilizando un cuestionario en la recolección de información. El soporte teórico que dio sentido al estudio fue el modelo de dos etapas propuesto por Mayer R. para la resolución de problemas matemáticos, el ciclo de modelación bajo la perspectiva cognitiva según Borromeo Ferri y la teoría de las representaciones de Goldin y Kaput. La investigación se centró específicamente en la fase de representación del modelo. Entre los principales hallazgos se destaca que cada participante hace su propia representación externa a conceptos como: sistema masa-resorte, peso, masa, punto de equilibrio, constante de elasticidad, punto de equilibrio, ley de Hooke, fuerza amortiguadora, fuerza externa, ley de Newton, entre otros. Se evidencian también dificultades en el tránsito del lenguaje natural al lenguaje matemático y la representación externa de cada una de los signos, símbolos o expresiones matemáticas inmersas en el problema de palabra, debido a que el resolutor tiene que construir un modelo mental de la situación real y plasmarlo en un modelo matemático. Lo anterior pone de manifiesto la importancia que tiene el conocimiento semántico en la etapa de traducción cuando se intentan resolver problemas como situaciones reales a modelar.Palabras clave: resolución de problemas, ciclos de modelación, problemas de palabra, representaciones externas, conocimiento extra matemático, modelación matemática. AbstractThis article presents the characterization of the semantic knowledge evidenced by a group of students in the external representation to problems of second order linear differential equations as mathematical models. The work was quantitative exploratory and descriptive using a questionnaire in the collection of information. The theoretical support that gave meaning to the study was the two-stage model proposed by Mayer R. for solving mathematical problems, the modeling cycle under the cognitive perspective according to Borromeo Ferri and the theory of representations of Goldin and Kaput. The research focused specifically on the representation phase of the model. Among the main findings is that each participant makes his own external representation to concepts such as: mass-spring system, weight, mass, equilibrium point, constant of elasticity, equilibrium point, Hooke's law, damping force, external force, law of Newton, among others. Difficulties are also evident in the transition from natural language to mathematical language and the external representation of each of the signs, symbols or mathematical expressions involved in the word problem, because the resolver has to construct a mental model of the real situation and translate it into a mathematical model. This demonstrates the importance of semantic knowledge in the translation stage when trying to solve problems as real situations to be modeledKeywords: problem solving, modeling cycles, word problems, external representations, extra mathematical knowledge, mathematical modeling.ResumoEste artigo apresenta a caracterização do conhecimento semântico evidenciado por um grupo de estudantes na representação externa a problemas de equações diferenciais lineares de segunda ordem como modelos matemáticos. O trabalho foi quantitativo exploratório e descritivo usando um questionário na coleta de informações. O suporte teórico que deu sentido ao estudo foi o modelo de dois estágios proposto por Mayer R. para resolver problemas matemáticos, o ciclo de modelagem sob a perspectiva cognitiva de acordo com Borromeo Ferri e a teoria das representações de Goldin e Kaput. A pesquisa focalizou especificamente a fase de representação do modelo. Entre os principais achados, cada participante faz sua própria representação externa para conceitos como: sistema de massa-mola, peso, massa, ponto de equilíbrio, constante de elasticidade, ponto de equilíbrio, lei de Hooke, força de amortecimento, força externa, lei de Newton, entre outros. As dificuldades também são evidentes na transição da linguagem natural para a linguagem matemática e a representação externa de cada um dos signos, símbolos ou expressões matemáticas envolvidas na palavra problema, porque o resolvedor tem que construir um modelo mental da situação real e traduzi-lo para um modelo matemático. Isso demonstra a importância do conhecimento semântico na fase de tradução ao tentar resolver problemas como situações reais a serem modeladas. ______________________________________________________ Palavras-chave: resolução de problemas, ciclos de modelagem, problemas de palavra, representação externa, conhecimento extra matemático, modelagem matemática


Sign in / Sign up

Export Citation Format

Share Document