Research Regarding the Evolution of Friction Coefficient in a Friction Torque Like a Plastic Material / Steel for Different Parameters

2019 ◽  
Vol 56 (4) ◽  
pp. 918-922
Author(s):  
Ivona Camelia Petre ◽  
Maria Cristiana Enescu ◽  
Elena Valentina Stoian
Keyword(s):  
Friction Coefficient ◽  
Coefficient Of Friction ◽  
Plastic Material ◽  
Normal Load ◽  
Slip Rate ◽  
General Purpose ◽  
Friction Torque ◽  
Theoretical Expression ◽  
The Coefficient Of Friction ◽  
Friction Surfaces

Explaining the phenomena occurring at the level of relative friction surfaces has become increasingly complex and often contradictory. Research over time has shown that the friction coefficient for a friction coupler is not a constant magnitude, as Amonton-Coulomb has stated, its values being dependent on a multitude of factors (normal load, slip rate, the nature of the material, the state of lubrication, etc.). The laws of the two are considered to be valid only under conditions of dry rubbing and elastic deformation of the surfaces in contact. The present paper proposes in the first part a study on the theoretical expression of the coefficient of friction. The experimental part of the paper highlights the variation of the coefficient of friction with the speed, loading and processing of the contact surface. It was made on a tribological stand of pin / disc type, and the coupler used was polymeric material called Turcit (for disc) / general purpose steel (for pine).

The Size of the Friction Coefficient Depending on the Size and Course of Normal Load

2014 ◽  
Vol 474 ◽  
pp. 303-308 ◽  
Author(s):  
Eva Labašová
Keyword(s):  
Friction Coefficient ◽  
Coefficient Of Friction ◽  
Normal Load ◽  
Testing Machine ◽  
Constant Load ◽  
Current Component ◽  
Rectangular Shape ◽  
The Coefficient Of Friction ◽  
Ring Method ◽  
Run Up

The coefficient of friction for the bronze material (CuZn25Al6) with inset graphite beds is investigated in the present paper. Friction coefficient was investigated experimentally by the testing machine Tribotestor`89 which uses the principle of the ring on ring method. Tribotestor`89 machine may be classed to the rotary tribometers. The tested sliding pairs were of the same material. The internal bushing performed a rotational movement with constant sliding speed (v = 0.8 m s-1). The external fixed bushing was exposed to the normal load, which was of different sizes and different variations. Process of load was increased from level 50 N to 200 N (400 N, 600 N) during run up 600 s, after the run up the appropriate level of load was held.The forth test had a rectangular shape of loading with direct current component 400 N and the amplitude 200 N period 600 s, the whole test took 1800 s. The obtained results reveal that friction coefficient decreases with the increase of normal load. Further, that the coefficient of friction was found smaller at constant load, as compared to rectangular shape of loading.

scholarly journals Effect of Stick - Slip Phenomena between Human Skin and UHMW Polyethylene

2021 ◽  
Vol 29 (3) ◽  
Author(s):  
Emad Kamil Hussein ◽  
Kussay Ahmed Subhi ◽  
Tayser Sumer Gaaz
Keyword(s):  
Friction Coefficient ◽  
Human Skin ◽  
Coefficient Of Friction ◽  
Normal Load ◽  
Static Friction ◽  
Time Interval ◽  
Dynamic Friction ◽  
Sliding Velocity ◽  
Stick Slip ◽  
The Coefficient Of Friction

The present paper investigates experimentally effect of applied load and different velocity on the coefficient of friction between two interacting surfaces (human skin and Ultra-high-molecular-weight polyethylene (UHMW- polyethylene) at static and dynamic friction. It is possible to conclude specific point based on the above practical part and frictional analysis of this investigation as the most important mechanical phenomenon was creep has been observed a stick time interval where the static friction force is significantly increased during this stroke. The analytical model for stick-slip of skin and UHMWPE is proposed. The difference between static and kinetic friction defines the amplitude of stick-slip phenomena. The contact pressure, the sliding velocity, and rigidity of system determine the stability conditions of the movement between skin and UHMWPE. Experiments were carried out by developing a device (friction measurement). Variations of friction coefficient during the time at different normal load 4.6 and 9.2 N and low sliding velocity 4, 5, 6 and 7 mm/min were experimentally investigated. The results showed that the friction coefficient varied with the normal load and low sliding velocity. At static friction, the coefficient of friction decreased when the time increases, whereas, at dynamic friction, the coefficient of friction decreased when the time increased at normal load 4.6 and 9.2 N.

Experimental Investigation of aluminum doping crumb rubber/epoxy composite in reciprocating motion

2015 ◽  
Vol 3 ◽  
pp. 1
Author(s):  
Goutam Chandra Karar ◽  
Nipu Modak
Keyword(s):  
Experimental Investigation ◽  
Coefficient Of Friction ◽  
Epoxy Composite ◽  
Normal Load ◽  
Crumb Rubber ◽  
The Other ◽  
Reciprocating Motion ◽  
Molding Process ◽  
Friction Tester ◽  
The Coefficient Of Friction

The experimental investigation of reciprocating motion between the aluminum doped crumb rubber /epoxy composite and the steel ball has been carried out under Reciprocating Friction Tester, TR-282 to study the wear and coefficient of frictions using different normal loads (0.4Kg, 0.7Kgand1Kg), differentfrequencies (10Hz, 25Hz and 40Hz).The wear is a function of normal load, reciprocating frequency, reciprocating duration and the composition of the material. The percentage of aluminum presents in the composite changesbut the other components remain the same.The four types of composites are fabricated by compression molding process having 0%, 10%, 20% and 30% Al. The effect of different parameters such as normal load, reciprocating frequency and percentage of aluminum has been studied. It is observed that the wear and coefficient of friction is influenced by the parameters. The tendency of wear goes on decreasing with the increase of normal load and it is minimum for a composite having 10%aluminum at a normal load of 0.7Kg and then goes on increasing at higher loads for all types of composite due to the adhesive nature of the composite. The coefficient of friction goes on decreasing with increasing normal loads due to the formation of thin film as an effect of heat generation with normal load.

Experimental study on the relationship between the friction coefficient and interference in locomotive axle press-fitting

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ting Wang ◽  
Hanfei Guo ◽  
Jianjun Qiao ◽  
Xiaoxue Liu ◽  
Zhixin Fan
Keyword(s):  
Friction Coefficient ◽  
Coefficient Of Friction ◽  
Friction Pair ◽  
Rolling Stock ◽  
Content Type ◽  
Press Fitting ◽  
The Press ◽  
The Coefficient Of Friction ◽  
The Relationship ◽  
Locomotive Wheels

PurposeTo address the lack of data in this field and determine the relationship between the coefficient of friction and the interference between locomotive wheels and axles, this study evaluates the theoretical relationship between the coefficient of friction and the interference under elastic deformation.Design/methodology/approachWhen using numerical analyses to study the mechanical state of the contacting components of the wheels and axle, the interference between the axle parts and the coefficient of friction between the axle parts are two important influencing factors. Currently, as the range of the coefficient of friction between the wheel and axle in interference remains unknown, it is generally considered that the coefficient of friction is only related to the materials of the friction pair; the relationship between the interference and the coefficient of friction is often neglected.FindingsA total of 520 press-fitting experiments were conducted for 130 sets of wheels and axles of the HXD2 locomotive with 4 types of interferences, in order to obtain the relationship between the coefficient of friction between the locomotive wheel and axle and the amount of interference. These results are expected to serve as a reference for selecting the coefficient of friction when designing axle structures with the rolling stock, research on the press-fitting process and evaluations of the fatigue life.Originality/valueThe study provides a basis for the selection of friction coefficient and interference amount in the design of locomotive wheels and axles.

The Dependence of the Friction Coefficient on the Size and Course of Sliding Speed

2014 ◽  
Vol 693 ◽  
pp. 305-310 ◽  
Author(s):  
Eva Labašová
Keyword(s):  
Friction Coefficient ◽  
Normal Load ◽  
Testing Machine ◽  
Current Component ◽  
Sliding Speed ◽  
Rectangular Shape ◽  
Coefficient Increase ◽  
The Coefficient Of Friction ◽  
Ring Method ◽  
Run Up

The coefficient of friction for the bronze material (CuZn25Al6) with insert graphite beds and other bronze material (CuSn12) are investigated in this paper. Friction coefficient was investigated experimentally by the testing machine Tribotestor`89 which uses the principle of the ring on ring method. The external fixed bushing was exposed to the normal load of the same size in all tests. Process of load was increased from level 50 N to 600 N during run up 300 s, after the run up the appropriate level of load was held. The internal bushing performed a rotational movement with constant sliding speed. The value of sliding speed was changed individually for every sample (v = 0.2 (0.3, 0.4) m.s-1). The forth test had a rectangular shape of sliding speed with direct current component 0.3 m.s-1 and the amplitude 0.1 m.s-1 period 300 s, the whole test took 2100 s. The obtained results reveal that friction coefficient increase with the increase of sliding speed.

scholarly journals Experimental Study on the Transition between Static and Kinetic Frictions of Steel/Shale Pairs

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Qin Lian ◽  
Chunxu Yang ◽  
Jifei Cao
Keyword(s):  
Friction Coefficient ◽  
Normal Load ◽  
Critical Distance ◽  
Dynamic Friction ◽  
Stick Slip ◽  
Dynamic Friction Coefficient ◽  
The Coefficient Of Friction ◽  
The Difference ◽  
Stick Slip Motion ◽  
Insight Into

The transition between static and kinetic frictions of steel/shale pairs has been studied. It was found that the coefficient of friction decreased exponentially from static to dynamic friction coefficient with increasing sliding displacement. The difference between static and dynamic friction coefficients and the critical distance Dc under the dry friction condition is much larger than that under the lubricated condition. The transition from static to dynamic friction coefficient is greatly affected by the normal load, quiescent time, and sliding velocity, especially the lubricating condition. Maintaining continuous lubrication of the contact area by the lubricant is crucial to reduce or eliminate the stick-slip motion. The results provide an insight into the transition from static to dynamic friction of steel/shale pairs.

Stresses Due to Tangential and Normal Loads on an Elastic Solid With Application to Some Contact Stress Problems

1953 ◽  
Vol 20 (2) ◽  
pp. 157-166
Author(s):  
J. O. Smith ◽  
Chang Keng Liu
Keyword(s):  
Plane Strain ◽  
Coefficient Of Friction ◽  
Contact Area ◽  
Normal Load ◽  
Elastic Solid ◽  
Real Variable ◽  
The Body ◽  
Shearing Stress ◽  
Tangential Load ◽  
The Coefficient Of Friction

Abstract The results of two-dimensional approach using real variable method to Hertz’s problem of contact of elastic bodies are presented. Both normal and tangential loads are assumed to be distributed in Hertzian fashion over the area of contact. The magnitude of the intensity of the tangential load is assumed to be linearly proportional to that of the normal load when sliding motion of the body is impending. The stresses in the elastic body due to the application of these loads on its boundary are presented in closed form for both plane-stress and plane-strain cases. A numerical value of f = 1/3 is assumed for the linear proportionality (coefficient of friction) between the tangential and normal loads in order that the distribution of stresses may be illustrated. The significance of the stress distribution, across the contact area and in the body, is also discussed. It is shown that when the combination of loads considered in the paper are applied at the contact area of bodies in contact the maximum shearing stress may be at the surface instead of beneath the surface. For example, for plane strain, if the coefficient of friction is f = 1/3, the maximum shearing stress is at the surface and is 43 per cent larger than the maximum shearing stress, which would be below the surface, that occurs when the normal force acts alone. The effect of range of normal stress and of shearing stress on the plane of maximum shear and on the plane of maximum octahedral shear on failure by progressive fracture (fatigue) is discussed.

scholarly journals Anisotropic Vibration Tactile Model and Human Factor Analysis for a Piezoelectric Tactile Feedback Device

Micromachines ◽  
2019 ◽  
Vol 10 (7) ◽  
pp. 448 ◽  
Author(s):  
Jichun Xing ◽  
Huajun Li ◽  
Dechun Liu
Keyword(s):  
Friction Coefficient ◽  
Coefficient Of Friction ◽  
Ciliary Body ◽  
Human Factor ◽  
Sliding Friction ◽  
Excitation Frequency ◽  
Tactile Feedback ◽  
Body Structure ◽  
Full Coverage ◽  
The Coefficient Of Friction

Tactile feedback technology has important development prospects in interactive technology. In order to enrich the tactile sense of haptic devices under simple control, a piezoelectric haptic feedback device is proposed. The piezoelectric tactile feedback device can realize tactile changes in different excitation voltage amplitudes, different excitation frequencies, and different directions through the ciliary body structure. The principle of the anisotropic vibration of the ciliary body structure was analyzed here, and a tactile model was established. The equivalent friction coefficient under full-coverage and local-coverage of the skin of the touch beam was deduced and solved. The effect of system parameters on the friction coefficient was analyzed. The results showed that in the full-coverage, the tactile effect is mainly affected by the proportion of the same directional ciliary bodies and the excitation frequency. The larger the proportion of the same direction ciliary body is, the smaller the coefficient of friction is. The larger the excitation frequency is, the greater the coefficient of friction is. In the local-coverage, the tactile effect is mainly affected by the touch position and voltage amplitude. When changing the touch pressure, it has a certain effect on the change of touch, but it is relatively weak. The experiment on the sliding friction of a cantilever touch beam and the experiment of human factor were conducted. The experimental results of the sliding friction experiment are basically consistent with the theoretical calculations. In the human factor experiment, the effects of haptic regulation are mainly affected by voltage or structure of the ciliary bodies.

scholarly journals Finger pad friction and its role in grip and touch

2013 ◽  
Vol 10 (80) ◽  
pp. 20120467 ◽  
Author(s):  
Michael J. Adams ◽  
Simon A. Johnson ◽  
Philippe Lefèvre ◽  
Vincent Lévesque ◽  
Vincent Hayward ◽  
...  
Keyword(s):  
Contact Zone ◽  
Coefficient Of Friction ◽  
Normal Load ◽  
Theoretical Models ◽  
Tactile Perception ◽  
Major Influence ◽  
Sliding Velocity ◽  
Stick Slip ◽  
The Coefficient Of Friction ◽  
Finger Pad

Many aspects of both grip function and tactile perception depend on complex frictional interactions occurring in the contact zone of the finger pad, which is the subject of the current review. While it is well established that friction plays a crucial role in grip function, its exact contribution for discriminatory touch involving the sliding of a finger pad is more elusive. For texture discrimination, it is clear that vibrotaction plays an important role in the discriminatory mechanisms. Among other factors, friction impacts the nature of the vibrations generated by the relative movement of the fingertip skin against a probed object. Friction also has a major influence on the perceived tactile pleasantness of a surface. The contact mechanics of a finger pad is governed by the fingerprint ridges and the sweat that is exuded from pores located on these ridges. Counterintuitively, the coefficient of friction can increase by an order of magnitude in a period of tens of seconds when in contact with an impermeably smooth surface, such as glass. In contrast, the value will decrease for a porous surface, such as paper. The increase in friction is attributed to an occlusion mechanism and can be described by first-order kinetics. Surprisingly, the sensitivity of the coefficient of friction to the normal load and sliding velocity is comparatively of second order, yet these dependencies provide the main basis of theoretical models which, to-date, largely ignore the time evolution of the frictional dynamics. One well-known effect on taction is the possibility of inducing stick–slip if the friction decreases with increasing sliding velocity. Moreover, the initial slip of a finger pad occurs by the propagation of an annulus of failure from the perimeter of the contact zone and this phenomenon could be important in tactile perception and grip function.

Study on the effects of nano-aluminum-oxide particulates on mechanical and tribological characteristics of chopped carbon fiber reinforced epoxy composites

2015 ◽  
Vol 231 (4) ◽  
pp. 403-422 ◽  
Author(s):  
Kali Dass ◽  
SR Chauhan ◽  
Bharti Gaur
Keyword(s):  
Carbon Fiber ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Normal Load ◽  
Epoxy Composites ◽  
Specific Wear Rate ◽  
Tribological Characteristics ◽  
X Ray ◽  
The Coefficient Of Friction ◽  
Mechanical And Tribological Characteristics

An experimental study has been carried out to investigate the mechanical and tribological characteristics of chopped carbon fiber (CCF) reinforced epoxy composites filled with nano-Al2O3 particulates, as a function of fiber and filler contents. The experiments were conducted using a pin-on-disc wear test apparatus under dry sliding conditions. The coefficient of friction and specific wear rate of these composites was determined as a function of applied normal load, sliding velocity, sliding distance, and reinforcement content. The tensile, flexural, and compression strengths of ortho cresol novalac epoxy and chopped carbon fiber (OCNE/CCF) filled composites are found to be within the ranges of 48–58.54 MPa, 115–156.56 MPa, and 48–61.15 MPa. Whereas the tensile, flexural, and compression strengths of OCNE/CCF/Al2O3-filled composites are found to be within the ranges of 96–110 MPa, 176–204.66 MPa, and 72–85.65 MPa, respectively. It has been observed that the coefficient of friction decreases and specific wear rate increases with increase in the applied normal loads. Further increases in the fiber (6 wt%) and particle (3 wt%) contents in the epoxy matrix resulted in a decrease of both the mechanical and tribological properties, but remains above that of the CCF reinforced epoxy composites. The worn surfaces of composites were examined with scanning electron microscopy equipped with energy dispersion X-ray analyzer and X-ray diffraction analysis technique to investigate the wear mechanisms.

Sign in / Sign up

Export Citation Format

Share Document