Schruppfräsbearbeitung von Verdichterscheiben/Milling of compressor disk - Identification of a cutting material and coating combination for high process reliability

2017 ◽  
Vol 107 (09) ◽  
pp. 674-680
Author(s):  
E. Prof. Abele ◽  
C. Hasenfratz ◽  
C. Praetzas ◽  
G. M. Schüler ◽  
C. Stark ◽  
...  
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Manufacturing Technology ◽  
Machining Process ◽  
Complex Task ◽  
Eine Hohe ◽  
Process Reliability ◽  
Rough Milling ◽  
Compressor Disk

Die Herstellung von Verdichterscheiben stellt hohe Ansprüche an die Fertigungstechnik. Neue, schwer zu zerspanende Materialien und Integralkonstruktionen erzeugen eine hohe Komplexität bei der Ausführung. Das Projekt „SchwerSpan“ stellt sich dieser Herausforderung und entwickelt einen Prozess zur Schruppfräsbearbeitung von Verdichterscheiben. Ziel des Projekts ist eine Reduktion der Werkzeugkosten bei erhöhtem Zeitspanvolumen.   The production of compressor disks places high demands on the manufacturing technology. A very complex task is created by new difficult-to-cut materials and integral components. The project “SchwerSpan” is taking on this task by developing a machining process for rough milling in the production of compressor disks. The aim of the process is to reduce the tool costs by increasing material removal rate.

Optimization of μEDM process assisted with rotating magnetic pulling force and ultrasonic vibration

2021 ◽  
pp. 095440892098440
Author(s):  
Gurpreet Singh ◽  
DR Prajapati ◽  
PS Satsangi
Keyword(s):  
Ultrasonic Vibration ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Machining Process ◽  
Micro Electrical Discharge Machining ◽  
Pulling Force ◽  
Tool Rotation

The micro-electrical discharge machining process is hindered by low material removal rate and low surface quality, which bound its capability. The assistance of ultrasonic vibration and magnetic pulling force in micro-electrical discharge machining helps to overcome this limitation and increase the stability of the machining process. In the present research, an attempt has been made on Taguchi based GRA optimization for µEDM assisted with ultrasonic vibration and magnetic pulling force while µEDM of SKD-5 die steel with the tubular copper electrode. The process parameters such as ultrasonic vibration, magnetic pulling force, tool rotation, energy and feed rate have been chosen as process variables. Material removal rate and taper of the feature have been selected as response measures. From the experimental study, it has been found that response output measures have been significantly improved by 18% as compared to non assisted µEDM. The best optimal combination of input parameters for improved performance measures were recorded as machining with ultrasonic vibration (U1), 0.25 kgf of magnetic pulling force (M1), 600 rpm of tool rotation (R2), 3.38 mJ of energy (E3) and 1.5 mm/min of Tool feed rate (F3). The confirmation trail was also carried out for the validation of the results attained by Grey Relational Analysis and confirmed that there is a substantial improvement with both assistance applied simultaneously.

Effect of Frequency to Ultrasonic Vibration-Assisted Wire-EDM

2019 ◽  
Vol 814 ◽  
pp. 127-131
Author(s):  
Patittar Nakwong ◽  
Apiwat Muttamara
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Electrical Discharge Machine ◽  
Machining Process ◽  
Wire Electrode ◽  
Ultrasonic Machine ◽  
Lower Amplitude ◽  
Wedm Process

Wire electrical discharge machine (WEDM) is non-conventional machining process. It can be used for hard cutting material. The study has been presented the combining WEDM with an ultrasonic machine (USM) with brass and tungsten were used as a wire electrode and workpiece respectively. The experiment was carried out with an ultrasonic transducer at 40, 80 kHz. The results were observed with the material removal rate (MRR) and surface roughness (Ra). This research introduced the method of USM setup and described the effected of vibration with the wire electrode on the displacement of amplitude. The result shows that the WEDM process with USM at 40 kHz can be more improved with the material removal rate and surface roughness than that of USM at 80 kHz. This can be explained that higher frequency affected to vibration displacement which makes lower amplitude.

Intelligent Modeling and Optimization of Material Removal Rate in Electric Discharge Diamond Grinding

2012 ◽  
Author(s):  
Pankaj Kumar Shrivastava ◽  
Avanish Kumar Dubey
Keyword(s):  
Material Removal Rate ◽  
Electric Discharge ◽  
Material Removal ◽  
Removal Rate ◽  
Iron Carbide ◽  
Hybrid Approach ◽  
Weight Ratio ◽  
Manufacturing Industries ◽  
Machining Process ◽  
Diamond Grinding

Metal matrix composites (MMCs) have wide applications in modern manufacturing industries due to their specific and improved technological characteristics such as high strength to weight ratio, high hardness, high thermal, corrosion and wear resistances. Such characteristics are highly demanded in automobile, aircraft and space research organizations. Shaping of MMCs has been a big challenge for manufacturing industries due to their superior mechanical properties and the peculiar microstructure composed of different phases in MMCs poses machining challenges. Unconventional machining methods have become an alternative to give desired shapes with intricate profiles and stringent design requirements. The aim of present research is to investigate the machining performance of copper-iron-carbide MMC using hybrid machining process, electric discharge diamond grinding (EDDG). A hybrid approach of neural network and genetic algorithm has been used to develop the intelligent model for material removal rate (MRR) and subsequent optimization with the experimental data obtained by scientifically designed experimentation.

scholarly journals An Experimental Study on the Precision Abrasive Machining Process of Hard and Brittle Materials with Ultraviolet-Resin Bond Diamond Abrasive Tools

Materials ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 125 ◽  
Author(s):  
Lei Guo ◽  
Xinrong Zhang ◽  
Shibin Chen ◽  
Jizhuang Hui
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Manufacturing Process ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Abrasive Machining ◽  
Machining Performance ◽  
Machined Surface ◽  
Ultraviolet Curable

Ultraviolet-curable resin was introduced as a bonding agent into the fabrication process of precision abrasive machining tools in this study, aiming to deliver a rapid, flexible, economical, and environment-friendly additive manufacturing process to replace the hot press and sintering process with thermal-curable resin. A laboratory manufacturing process was established to develop an ultraviolet-curable resin bond diamond lapping plate, the machining performance of which on the ceramic workpiece was examined through a series of comparative experiments with slurry-based iron plate lapping. The machined surface roughness and weight loss of the workpieces were periodically recorded to evaluate the surface finish quality and the material removal rate. The promising results in terms of a 12% improvement in surface roughness and 25% reduction in material removal rate were obtained from the ultraviolet-curable resin plate-involved lapping process. A summarized hypothesis was drawn to describe the dynamically-balanced state of the hybrid precision abrasive machining process integrated both the two-body and three-body abrasion mode.

Study on machining mechanism of high viscoelastic abrasive flow machining for surface finishing

2016 ◽  
Vol 231 (4) ◽  
pp. 608-617 ◽  
Author(s):  
Zhiguo Dong ◽  
Gang Ya ◽  
Jiancheng Liu
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Experimental Tests ◽  
Normal Pressure ◽  
Machining Process ◽  
Surface Finishing ◽  
Abrasive Flow Machining ◽  
Machining Mechanism ◽  
Flow Pressure

Abrasive flow machining is a pragmatic machining process used for part finishing. This article primarily focuses on the study of machining mechanism of high viscoelastic abrasive flow machining, with the aim to understand the relation among the abrasive media’s flow pressure, the material removal rate and the machining quality. The theoretical calculation models of the normal pressure on the inner surface of a circular tube and the wall sliding velocity are established based on rheology theory. The material removal rate of abrasive flow machining with a high viscoelastic abrasive media is derived. Numerical simulations with various machining conditions were conducted using the mathematical models proposed in this research and the obtained findings are discussed. The feasibility of these models introduced for high viscoelastic abrasive machining is also investigated and verified through actual experimental tests.

Influence of Process Parameters on Characteristics of Electrical Discharge Machining of PH17-4 Stainless Steel

2015 ◽  
Vol 14 (03) ◽  
pp. 189-202 ◽  
Author(s):  
V. Vikram Reddy ◽  
P. Madar Valli ◽  
A. Kumar ◽  
Ch. Sridhar Reddy
Keyword(s):  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Surface Hardness ◽  
Machining Process ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time

In the present work, an investigation has been made into the electrical discharge machining process during machining of precipitation hardening stainless steel PH17-4. Taguchi method is used to formulate the experimental layout, to analyze the effect of each process parameter on machining characteristics and to predict the optimal choice for each electrical discharge machining process parameters namely, peak current, pulse on time and pulse off time that give up optimal process performance characteristics such as material removal rate, surface roughness, tool wear rate and surface hardness. To identify the significance of parameters on measured response, the analysis of variance has been done. It is found that parameters peak current and pulse on time have the significant affect on material removal rate, surface roughness, tool wear rate and surface hardness. However, parameter pulse off time has significant affect on material removal rate. Confirmation tests are conducted at their respective optimum parametric settings to verify the predicted optimal values of performance characteristics.

Optimization of Process Parameters on Ti-6Al-4V Using Central Composite Design Method

2011 ◽  
Vol 189-193 ◽  
pp. 1393-1400 ◽  
Author(s):  
M.M. Rahman
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Machining Process ◽  
Peak Current ◽  
Long Pulse ◽  
Pulse On Time

Electrical discharge machining (EDM) is relatively modern machining process having distinct advantages over other machining processes and able to machine Ti-alloys effectively. This paper attempts to investigate the effects of process parameters on output response of titanium alloy Ti-6Al-4V in EDM utilizing copper tungsten as an electrode and positive polarity of the electrode. Mathematical models for material removal rate (MRR), electrode wear rate (EWR) and surface roughness (SR) are developed in this paper. Design of experiments method and response surface methodology techniques are implemented. The validity test of the fit and adequacy of the proposed models has been carried out through analysis of variance. It can be seen that as the peak current increases the TWR decreases till certain ampere and then increases. The excellent surface finish is investigated in this study at short pulse on time and in contrast the long pulse duration causes the lowest EWR. Long pulse off time provides minimum EWR and the impact of pulse interval on EWR depends on peak current. The result leads to wear rate of electrode and economical industrial machining by optimizing the input parameters. It found that the peak current, servo voltage and pulse on time are significant in material removal rate and surface roughness. Peak current has the greater impact on surface roughness and material removal rate.

scholarly journals Tool Wear Rate Prediction by using Optimization Techniques

2019 ◽  
Vol 9 (2) ◽  
pp. 1271-1277
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Optimization Techniques ◽  
Machining Process ◽  
Machining Parameters ◽  
Tungsten Carbides ◽  
Electro Discharge Machining ◽  
Pulse On Time

Electro discharge machining is a non-traditional machining process used for machining hard-to-machine materials, such as various grades of titanium alloys, heat-treated alloy steels, composites, tungsten carbides, and so forth. These materials are hard to machine with customary machining procedures like drilling, milling and hence electro-discharge machining is used to machine such materials to get better quality and efficiency. These materials are generally utilized in current industries like die making industries, aeronautics, nuclear industries, and medical fields. This type of machining is thermalbased, and machining takes place due to repetitive electric sparks that generate between workpiece and tool. Both tools and workpieces are inundated in a dielectric liquid, which has two primary functions. In the first place, it behaves like a medium between the work metal and the tool. Second, it is a flushing agent to expel the machined metal from the machined zone. Machining parameters like a pulse on time, current, wire feed the tool and gap voltage affect the output responses like surface roughness and material removal rate. The material removal rate is a significant parameter that determines machining efficiency. Surface roughness is also a vital parameter that decides machining quality. A lot of research has been conducted to determine the optimum parameters for obtaining the best results. In the present work, a comprehensive review of different types of EDM and the effect of various machining parameters on the surface roughness, material removal rate, and other response parameters has been done.

scholarly journals Multi-Objective Process Parameter Optimization for Surface Roughness and Material Removal Rate in Face Milling of Al 6061 T6 Alloy

2019 ◽  
Vol 9 (2) ◽  
pp. 137-142
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Face Milling ◽  
Machining Process ◽  
Depth Of Cut ◽  
Al 6061

This study uses Taguchi methodology and Gray Relational Analysis approach to explore the optimization of face milling process parameters for Al 6061 T6 alloy.Surface Roughness (Ra), Material Removal Rate (MRR) has been identified as the objective of performance and productivity.The tests were performed by selecting cutting speed (mm / min), feed rate (mm / rev) and cutting depth (mm) at three settings on the basis of Taguchi's L9 orthogonal series.The grey relational approach was being used to establish a multiobjective relationship between both the parameters of machining and the characteristics of results. To find the optimum values of parameters in the milling operation, the response list and plots are used and found to be Vc2-f1-d3. To order to justify the optimum results, the confirmation tests are performed.The machining process parameters for milling were thus optimized in this research to achieve the combined goals such as low surface roughness and high material removal rate on Aluminum 6061 t6.It was concluded that depth of cut is the most influencing parameter followed by feed rate and cutting velocity.

scholarly journals Improve the Material Removal Rate of Electrochemical Grinding on Monel 400 Using RSM

2019 ◽  
Vol 8 (2) ◽  
pp. 3219-3222
Keyword(s):  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Electrochemical Machining ◽  
Machining Process ◽  
Depth Of Cut ◽  
Grinding Wheel ◽  
Mechanical Grinding ◽  
Monel 400 ◽  
Electrochemical Grinding

Electrochemical grinding is combination of electrochemical machining and mechanical grinding process.in this process 90%-98% percentage of material are removed by electrochemical machining, only 3%-5% of materials can only remove by mechanical grinding process. Faradays law of electrolysis (or) reverse electroplating act as a basic principle for this ECG process. This ECG has various advantages than other machining process for high strength materials .low induvial stress, large depth of cut .here Monel 400 alloy take base material ,its Ni-Cu alloy so it’s have very high level corrosion resistance, so it’s used in marine engineering ,heat exchanger. Here silicon carbide abrasive insulated brass grinding wheel used instead of copper bonded diamond wheel. Voltage, electrolyte concentration, electrolyte flowrate take are the parameters of this process. Three factors and two levels of RSM methodology takes for optimization. The Analysis of variance (ANOVA) has been delivers the variation between the parameters performed to develop mathematical model. The parameters high voltage and concentration of electrolyte to produce maximum material removal rate.

Sign in / Sign up

Export Citation Format

Share Document