scholarly journals Aerodynamic Performances of Paper Planes

2020 ◽  
Vol 77 (1) ◽  
pp. 124-131
Author(s):  
Noor Iswadi Ismail ◽  
Zurriati Mohd Ali ◽  
Iskandar Shah Ishak ◽  
R.M. Noor ◽  
Rosniza Rabilah
Keyword(s):  
Lift Coefficient ◽  
The Other ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Aerodynamic Efficiency ◽  
Ansys Cfx ◽  
Wide Range ◽  
Aerodynamic Performances ◽  
Paper Plane ◽  
Stall Angle

Paper plane has a high potential to be upgraded as a Micro Air Vehicle (MAV). Due to its simplicity, paper plane offers easier design option compared to the biological inspired designs as shown in recent MAV development. However, researchers have underestimate and overlook the basic aerodynamic performance induced by these paper planes. This is due to its common usage as toys and wide range of paper plane design. Thus, the objective for current work is to analyse and compare the aerodynamics forces and its performance for selected paper plane design known as Glider, Wide Stunt Glider Plane and Stunt plane. A series of CFD simulations on each paper plane was executed by using ANSYS-CFX module. A steady state, incompressible flow Navier-Stokes equation (RANS) combined with Shear Stress Turbulence (SST) model were used in this works to solve flow problem over the paper planes. The analysis is mainly conducted to study and compare the lift coefficient (), drag coefficient ()and aerodynamic efficiency () performances for each paper planes. The results show that the Glider paper plane has managed to produce better performances in terms overall magnitude, stall angle, wider angle of attack (?) envelope and higher maximum lift coefficient magnitude compared to the other paper plane design. However, Glider paper plane has the least distributions by producing at least 14.3% larger magnitude compared to the other plane design at certain ? region. Instead, The Wide Stunt has promisingly produced better distribution by producing lower value compared to the other plane design. Based on performance, the Wide Stunt paper plane has produced better and maximum aerodynamic efficiency () magnitudes compared to the other design. Wide Stunt paper plane induced at least 6.4% better magnitude compared to the other paper plane design. Based on these results, it can be concluded that Wide Stunt paper plane has promising advantages which are very crucial for the paper plane especially during hovering operation, take-off and landing manoeuvre.

Method for Non-Dimensional Tip Leakage Flow Characterization in Radial Turbines

2018 ◽  
Author(s):  
José Ramón Serrano ◽  
Roberto Navarro ◽  
Luis Miguel García-Cuevas ◽  
Lukas Benjamin Inhestern
Keyword(s):  
Suction Side ◽  
Tip Clearance ◽  
Navier Stokes ◽  
The Novel ◽  
Tip Leakage Flow ◽  
Navier Stokes Equation ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Wide Range ◽  
Clearance Flow

Tip leakage loss characterization and modeling plays an important role in small size radial turbine research. The momentum of the flow passing through the tip gap is highly related with the tip leakage losses. The ratio of fluid momentum driven by the pressure gradient between suction side and pressure side and the fluid momentum caused by the shroud friction has been widely used to analyze and to compare different sized tip clearances. However, the commonly used number for building this momentum ratio lacks some variables, as the blade tip geometry data and the viscosity of the used fluid. To allow the comparison between different sized turbocharger turbine tip gaps, work has been put into finding a consistent characterization of radial tip clearance flow. Therefore, a non-dimensional number has been derived from the Navier Stokes Equation. This number can be calculated like the original ratio over the chord length. Using the results of wide range CFD data, the novel tip leakage number has been compared with the traditional and widely used ratio. Furthermore, the novel tip leakage number can be separated into three different non-dimensional factors. First, a factor dependent on the radial dimensions of the tip gap has been found. Second, a factor defined by the viscosity, the blade loading, and the tip width has been identified. Finally, a factor that defines the coupling between both flow phenomena. These factors can further be used to filter the tip gap flow, obtained by CFD, with the influence of friction driven and pressure driven momentum flow.

Experimental analysis of cell pattern on grid fin aerodynamics in subsonic flow

2019 ◽  
Vol 234 (3) ◽  
pp. 537-562
Author(s):  
Manish Tripathi ◽  
Mahesh M Sucheendran ◽  
Ajay Misra
Keyword(s):  
Subsonic Flow ◽  
Lift Coefficient ◽  
Aerodynamic Performance ◽  
Aerodynamic Efficiency ◽  
Grid Fin ◽  
Stall Angle ◽  
The Individual ◽  
The Impact ◽  
Control Surfaces

Grid fins consisting of a lattice of high aspect ratio planar members encompassed by an outer frame are unconventional control surfaces used on numerous missiles and bombs due to their enhanced lifting characteristics at high angles of attack and across wider Mach number regimes. The current paper accomplishes and compares the effect of different grid fin patterns on subsonic flow aerodynamics of grid fins by virtue of the determination of their respective aerodynamic forces. Furthermore, this study deliberates the impact of gap variation on aerodynamics of different patterns. Results enunciate enhanced aerodynamic efficiency, and lift slope for web-fin cells and single diamond patterns compared to the baseline model. Moreover, the study indicates improved aerodynamic performance for diamond patterns with higher gaps by providing elevated maximum lift coefficient, delayed stall angle, and comparable drag at lower angles. The study established the presence of an additional effect termed as the inclination effect alongside the cascade effect leading to deviations with respect to lift, stall, and aerodynamic efficiency amongst different gap variants of the individual patterns. Thus, optimization based on the aerodynamic efficiency, stall angle requirements, and construction cost by optimum pattern and gap selection can be carried out through this analysis, which can lead to elevated aerodynamic performance for grid fins.

Effects of leading-edge bevel angle on the aerodynamic forces of a non-slender 50° delta wing

2005 ◽  
Vol 109 (1098) ◽  
pp. 403-407 ◽  
Author(s):  
J. J. Wang ◽  
S. F. Lu
Keyword(s):  
Delta Wing ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Relative Thickness ◽  
Aerodynamic Performances ◽  
Stall Angle ◽  
Drag Ratio ◽  
Low Speed Wind Tunnel ◽  
Lift To Drag Ratio ◽  
Blunt Leading Edge

Abstract The aerodynamic performances of a non-slender 50° delta wing with various leading-edge bevels were measured in a low speed wind tunnel. It is found that the delta wing with leading-edge bevelled leeward can improve the maximum lift coefficient and maximum lift to drag ratio, and the stall angle of the wing is also delayed. In comparison with the blunt leading-edge wing, the increment of maximum lift to drag ratio is 200%, 98% and 100% for the wings with relative thickness t/c = 2%, t/c = 6.7% and t/c = 10%, respectively.

scholarly journals Experimental and Computational Investigation of Spoiler Deployment on Wing Stall

2021 ◽  
Author(s):  
Scott Lindsay
Keyword(s):  
Wind Tunnel ◽  
Drag Coefficient ◽  
Computational Study ◽  
Lift Coefficient ◽  
Wind Tunnel Experiment ◽  
Chord Length ◽  
Aerodynamic Efficiency ◽  
Stall Angle ◽  
Wing Stall ◽  
High Angles Of Attack

Upper surface flaps commonly referred to as spoilers or drag brakes can increase maximum lift, and improve aerodynamic efficiency at high, near-stall angles of attack. This phenomenon was studied experimentally and computationally using a 0.307626 m chord length NACA 2412 airfoil in six different configurations, and one baseline clean configuration. A wind tunnel model was placed in the Ryerson Low Speed Wind Tunnel (atmospheric, closed-circuit, 3 ft × 3 ft test section) at a Reynold’s number of approximately 780,000 and a Mach number of 0.136. The wind tunnel study increased the lift coefficient by 0.393%-2.497% depending on the spoiler configuration. A spoiler of 10% chord length increased the maximum lift coefficient by 2.497 % when deflected 8º, by 2.110% when deflected 15º, and reduced the maximum lift coefficient by 2.783% when deflected 25º. A spoiler of 15% chord length produced smaller maximum lift coefficient gains; 0.393% when deflected 8º, by 1.760% when deflected 15º, and reduced the maximum lift coefficient by 4.475% when deflected 25º. Deflecting the spoiler increased the stall angle between 37.658% and 87.544% when compared with the clean configuration. The drag coefficient of spoiler configurations was lower than the clean configuration at angles of attack above 18º. The combination of the increased lift and reduced drag at angles of attack above 18º created by the spoiler configurations resulted in a higher aerodynamic efficiency than the clean configuration case. A 10% chord length spoiler deflected at 8º produced the highest aerodynamic efficiency gains. At low angles of attack, the computational study produced consistently higher lift coefficients compared with the wind tunnel experiment. The lift-slope was consistent with the wind tunnel experiment lift-slope. The spoiler airfoil stall behaviour was inconsistent with the results from the wind tunnel experiment. The drag coefficient results were consistent with the wind tunnel experiment at low angles of attack. However, the spoiler equipped airfoils did not reduce drag at high angles of attack. Therefore, the computational model was not valid for the spoiler configurations at high angles of attack.

Numerical and experimental study of the laminar separation bubble over SS007 airfoil for micro aerial vehicles

2020 ◽  
Vol 92 (8) ◽  
pp. 1125-1131
Author(s):  
Somashekar V. ◽  
Immanuel Selwyn Raj A.
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Lift Coefficient ◽  
Laminar Separation Bubble ◽  
Micro Aerial Vehicle ◽  
Aerodynamic Efficiency ◽  
Content Type ◽  
Laminar Separation ◽  
Aerodynamic Performances ◽  
Aerial Vehicle

Purpose This paper aims to deal with the numerical investigation of laminar separation bubble (LSB) characteristics (length and height of the bubble) of SS007 airfoil at the chord Reynolds number of Rec = 0.68 × 105 to 10.28 × 105. Design/methodology/approach The numerical simulations of the flow around SS007 airfoil were carried out by using the commercial fluid dynamics (CFD) software, ANalysis system (ANSYS) 15. To solve the governing equations of the flow, a cell-centred control volume space discretisation approach is used. Wind tunnel experiments were conducted at the chord-based Reynolds number of Rec = 1.6 × 105 to validate the aerodynamic characteristics over SS007 airfoil. Findings The numerical results revealed that the LSB characteristics of a SS007 airfoil, and the aerodynamic performances are validated with experimental results. The lift and drag coefficients for both numerical and experimental results show very good correlation at Reynolds number 1.6 × 105. The lift coefficient linearly increases with the increasing angle of attack (AOA) is relatively small. The corresponding drag coefficient was found to be very small. After the formation of LSB which leads to burst to cause airfoil stall, the lift coefficient decreases and increases the drag coefficient. Practical implications Low Reynolds number and LSB characteristics concept in aerodynamics is predominant for both civilian and military applications. These include high altitude devices, wind turbines, human powered vehicles, remotely piloted vehicles, sailplanes, unmanned aerial vehicle and micro aerial vehicle. In this paper, the micro aerial vehicle flight conditions considered and investigated the LSB characteristics for different Reynolds number. To have better aerodynamic performances, it is strongly recommended to micro aerial vehicle (MAV) design engineers that the MAV is to fly at 12 m/s (cruise speed). Social implications MAVs and unmanned aerial vehicles seem to give some of the technical challenges of nature conservation monitoring and law enforcement a versatile, reliable and inexpensive solution. Originality/value The SS007 airfoil delays the flow separation and improves the aerodynamic efficiency by increasing the lift and decreasing the drag. The maximum increase in aerodynamic efficiency is 12.5% at stall angle of attack compared to the reference airfoil at Re = 2 × 105. The results are encouraging and this airfoil could have better aerodynamic performance for the development of MAV.

scholarly journals Mathematical problems in modeling artificial heart

1995 ◽  
Vol 1 (3) ◽  
pp. 245-254 ◽  
Author(s):  
N. U. Ahmed
Keyword(s):  
Blood Flow ◽  
Boundary Conditions ◽  
Stokes Equation ◽  
Artificial Heart ◽  
Moving Boundary ◽  
Hyperbolic Type ◽  
The Other ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Heart Chamber

In this paper we discuss some problems arising in mathematical modeling of artificial hearts. The hydrodynamics of blood flow in an artificial heart chamber is governed by the Navier-Stokes equation, coupled with an equation of hyperbolic type subject to moving boundary conditions. The flow is induced by the motion of a diaphragm (membrane) inside the heart chamber attached to a part of the boundary and driven by a compressor (pusher plate). On one side of the diaphragm is the blood and on the other side is the compressor fluid. For a complete mathematical model it is necessary to write the equation of motion of the diaphragm and all the dynamic couplings that exist between its position, velocity and the blood flow in the heart chamber. This gives rise to a system of coupled nonlinear partial differential equations; the Navier-Stokes equation being of parabolic type and the equation for the membrane being of hyperbolic type. The system is completed by introducing all the necessary static and dynamic boundary conditions. The ultimate objective is to control the flow pattern so as to minimize hemolysis (damage to red blood cells) by optimal choice of geometry, and by optimal control of the membrane for a given geometry. The other clinical problems, such as compatibility of the material used in the construction of the heart chamber, and the membrane, are not considered in this paper. Also the dynamics of the valve is not considered here, though it is also an important element in the overall design of an artificial heart. We hope to model the valve dynamics in later paper.

scholarly journals Experimental and Computational Investigation of Spoiler Deployment on Wing Stall

2021 ◽  
Author(s):  
Scott Lindsay
Keyword(s):  
Wind Tunnel ◽  
Drag Coefficient ◽  
Computational Study ◽  
Lift Coefficient ◽  
Wind Tunnel Experiment ◽  
Chord Length ◽  
Aerodynamic Efficiency ◽  
Stall Angle ◽  
Wing Stall ◽  
High Angles Of Attack

Upper surface flaps commonly referred to as spoilers or drag brakes can increase maximum lift, and improve aerodynamic efficiency at high, near-stall angles of attack. This phenomenon was studied experimentally and computationally using a 0.307626 m chord length NACA 2412 airfoil in six different configurations, and one baseline clean configuration. A wind tunnel model was placed in the Ryerson Low Speed Wind Tunnel (atmospheric, closed-circuit, 3 ft × 3 ft test section) at a Reynold’s number of approximately 780,000 and a Mach number of 0.136. The wind tunnel study increased the lift coefficient by 0.393%-2.497% depending on the spoiler configuration. A spoiler of 10% chord length increased the maximum lift coefficient by 2.497 % when deflected 8º, by 2.110% when deflected 15º, and reduced the maximum lift coefficient by 2.783% when deflected 25º. A spoiler of 15% chord length produced smaller maximum lift coefficient gains; 0.393% when deflected 8º, by 1.760% when deflected 15º, and reduced the maximum lift coefficient by 4.475% when deflected 25º. Deflecting the spoiler increased the stall angle between 37.658% and 87.544% when compared with the clean configuration. The drag coefficient of spoiler configurations was lower than the clean configuration at angles of attack above 18º. The combination of the increased lift and reduced drag at angles of attack above 18º created by the spoiler configurations resulted in a higher aerodynamic efficiency than the clean configuration case. A 10% chord length spoiler deflected at 8º produced the highest aerodynamic efficiency gains. At low angles of attack, the computational study produced consistently higher lift coefficients compared with the wind tunnel experiment. The lift-slope was consistent with the wind tunnel experiment lift-slope. The spoiler airfoil stall behaviour was inconsistent with the results from the wind tunnel experiment. The drag coefficient results were consistent with the wind tunnel experiment at low angles of attack. However, the spoiler equipped airfoils did not reduce drag at high angles of attack. Therefore, the computational model was not valid for the spoiler configurations at high angles of attack.

scholarly journals Numerical Simulation on Aerodynamics of Multi-Element Airfoil with Drooped Spoiler in Ground Effect

2019 ◽  
Vol 37 (1) ◽  
pp. 167-176
Author(s):  
Jiang Liu ◽  
Junqiang Bai ◽  
Guozhu Gao ◽  
Min Chang ◽  
Nan Liu
Keyword(s):  
Lift Coefficient ◽  
Angle Of Attack ◽  
Ground Effect ◽  
Lower Surface ◽  
Navier Stokes ◽  
High Angle ◽  
High Angle Of Attack ◽  
Ride Height ◽  
Navier Stokes Equation ◽  
Sst Turbulence Model

By using the finite volume method and k-ω SST turbulence model to solve the Reynolds Average Navier-Stokes equation and using the slipping wall to simulate the relative movement of the ground, the ground effect on the aerodynamic characteristic of multi-element airfoil with drooped spoiler is investigated numerically, and the reason why the lift coefficient decreased in ground effect is analyzed. The results indicate that, with the reduction in ride height, the lift and the drag decrease and the lift-drag ratio increases for the multi-element airfoil; the amplitude of the reduction in the lift coefficient increases with the reduction in ride height and the increase in the angle of attack, the maximum of lift coefficient can be reduced by about 22%; with the effect of ground, the losses of suction at upper surface make the lift decrease, the increases of pressure at lower surface make the lift increase, the variation of the lift coefficient for the main wing caused by the former is more than three times that of the latter. Analyzing the reason why the lift coefficient decreases showed that:on the one hand, ground effect on the lift coefficient for clean airfoil is changed with the range of angle of attack. For the low-to-moderate angle of attack, the lift coefficient increases; for the high angle of attack, the lift coefficient decreases. But multi-element airfoil works in the takeoff and landing stage for the high angle of attack, which causes the reduction of the lift coefficient in ground effect. On the other hand, the increase of the lift coefficient caused by the deflection of spoiler decreases with the reduction in ride height and the maximum reduction can be about 50%, which illustrates that ground effect makes interaction of the front and back section for the multi-element airfoil weak, resulting in further decreasing the coefficient for the multi-element airfoil.

Rapid gust response simulation of large civil aircraft using computational fluid dynamics

2017 ◽  
Vol 121 (1246) ◽  
pp. 1795-1807 ◽  
Author(s):  
P. Bekemeyer ◽  
R. Thormann ◽  
S. Timme
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Stokes Equations ◽  
Lift Coefficient ◽  
Computational Cost ◽  
Aircraft Design ◽  
Navier Stokes ◽  
Surface Pressure Distribution ◽  
Wide Range ◽  
Civil Aircraft

ABSTRACTSeveral critical load cases during the aircraft design process result from atmospheric turbulence. Thus, rapidly performable and highly accurate dynamic response simulations are required to analyse a wide range of parameters. A method is proposed to predict dynamic loads on an elastically trimmed, large civil aircraft using computational fluid dynamics in conjunction with model reduction. A small-sized modal basis is computed by sampling the aerodynamic response at discrete frequencies and applying proper orthogonal decomposition. The linear operator of the Reynolds-averaged Navier-Stokes equations plus turbulence model is then projected onto the subspace spanned by this basis. The resulting reduced system is solved at an arbitrary number of frequencies to analyse responses to 1-cos gusts very efficiently. Lift coefficient and surface pressure distribution are compared with full-order, non-linear, unsteady time-marching simulations to verify the method. Overall, the reduced-order model predicts highly accurate global coefficients and surface loads at a fraction of the computational cost, which is an important step towards the aircraft loads process relying on computational fluid dynamics.

Numerical Study on Aerodynamic Performances of CRH3 under Crosswind

2012 ◽  
Vol 215-216 ◽  
pp. 992-997
Author(s):  
Hong Yuan Su ◽  
Ming Li ◽  
Dong Ping Wang ◽  
Feng Liu
Keyword(s):  
High Speed ◽  
Numerical Study ◽  
Lateral Force ◽  
Navier Stokes ◽  
Navier Stokes Equation ◽  
Aerodynamic Properties ◽  
Aerodynamic Performances ◽  
Volume Method ◽  
Incompressible Navier Stokes Equation ◽  
Multiple Units

Based on 3D steady and incompressible Navier-Stokes equation and standard k-ε turbulent model, numerical calculation for the aerodynamic properties of EMU (Electric Multiple Units) CRH3 (China Railway High-Speed 3)running in crosswind were carried out by finite volume method. Aerodynamic performances of EMU CRH3 were analyzed and compared, when the EMU was running in different speed and under the crosswinds of different velocity. The research showed that with the change of speed of train and crosswind, the surface pressure and aerodynamic forces altered according to a certain rule. Compared with the drag, the change of lift and lateral force caused by the increase of crosswind were more serious. When the speed of train was constant of 200km/h, 250km/h and 300km/h, the drag of train increased by 26.7%, 20.4% and 19.8% respectively as the speed of crosswind increased from 12.5m/s to 30m/s, the lift of train increased by 340.7%, 331.7% and 337.1% respectively, and the lateral force of train increases by 296.3%, 266.0% and 150.2% respectively. As the speed of crosswind increases, the increase of drag caused by the acceleration of train is more serious than lift and lateral force.

Sign in / Sign up

Export Citation Format

Share Document