scholarly journals Numerical Analysis of The Thermo-Convective Behaviour of an Al2O3-H2O Nanofluid Flow Inside a Channel with Trapezoidal Corrugations

2021 ◽  
Vol 89 (2) ◽  
pp. 114-127
Author(s):  
Mostefaoui Amina ◽  
Saim Rachid ◽  
Abboudi Saïd
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Volume Fraction ◽  
High Volume ◽  
Reynolds Numbers ◽  
Constant Heat Flux ◽  
Nanofluid Flow ◽  
Nanoparticle Diameter ◽  
Flow Through ◽  
Volume Method

In this present article, a study of the dynamic and thermal behavior of the Al2O3-water nanofluid flow through a channel provided with trapezoidal undulations, under the action of a constant heat flux. To do this, the effect of various volume fractions (0-4%) and that of the nanoparticle diameter (30, 40, 60 nm) on the heat transfer and pressure drop within the channel was analyzed, for a range of Reynolds numbers between 100 to 1000. The equations governing the fluid flow, namely the equations of continuity, momentum and energy were integrated and discretized based on the finite volume method (FVM). The obtained results indicated that using nanofluids with a high-volume fraction and a small nanoparticle diameter makes it possible to improve the performance of the system in terms of heat transfer, pressure drop and friction factor.

scholarly journals Heat transfer analysis of nanofluid flow through backward facing step

2020 ◽  
Vol 307 ◽  
pp. 01010 ◽  
Author(s):  
Ahlem Boudiaf ◽  
Fetta Danane ◽  
Youb Khaled Benkahla ◽  
Walid Berabou ◽  
Mahdi Benzema ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Thermal Characteristics ◽  
Heat Transfer Analysis ◽  
Backward Facing Step ◽  
Nanofluid Flow ◽  
Numerical Predictions ◽  
Flow Through ◽  
Volume Method

This paper presents the numerical predictions of hydrodynamic and thermal characteristics of nanofluid flow through backward facing step. The governing equations are solved through the finite volume method, as described by Patankar, by taking into account the associated boundary conditions. Empirical relations were used to give the effective dynamic viscosity and the thermal conductivity of the nanofluid. Effects of different key parameters such as Reynolds number, nanoparticle solid volume fraction and nanoparticle solid diameter on the heat transfer and fluid flow are investigated. The results are discussed in terms of the average Nusselt number and streamlines.

scholarly journals Numerical Investigation of Heat Transfer Enhancement in a Rectangular Heated Pipe for Turbulent Nanofluid

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Hooman Yarmand ◽  
Samira Gharehkhani ◽  
Salim Newaz Kazi ◽  
Emad Sadeghinezhad ◽  
Mohammad Reza Safaei
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Volume Fraction ◽  
Rectangular Channel ◽  
Thermal Characteristics ◽  
Reynolds Numbers ◽  
Constant Heat Flux ◽  
Energy Equations ◽  
Volume Method ◽  
Good Agreement

Thermal characteristics of turbulent nanofluid flow in a rectangular pipe have been investigated numerically. The continuity, momentum, and energy equations were solved by means of a finite volume method (FVM). The symmetrical rectangular channel is heated at the top and bottom at a constant heat flux while the sides walls are insulated. Four different types of nanoparticles Al2O3, ZnO, CuO, and SiO2at different volume fractions of nanofluids in the range of 1% to 5% are considered in the present investigation. In this paper, effect of different Reynolds numbers in the range of 5000 < Re < 25000 on heat transfer characteristics of nanofluids flowing through the channel is investigated. The numerical results indicate that SiO2-water has the highest Nusselt number compared to other nanofluids while it has the lowest heat transfer coefficient due to low thermal conductivity. The Nusselt number increases with the increase of the Reynolds number and the volume fraction of nanoparticles. The results of simulation show a good agreement with the existing experimental correlations.

scholarly journals Entropy generation of zirconia-water nanofluid flow through rectangular micro-channel

2018 ◽  
Vol 22 (Suppl. 5) ◽  
pp. 1395-1405
Author(s):  
Cuneyt Uysal ◽  
Kamil Arslan ◽  
Huseyin Kurt
Keyword(s):  
Entropy Generation ◽  
Volume Fraction ◽  
Constant Heat Flux ◽  
Bottom Surface ◽  
Bejan Number ◽  
Micro Channel ◽  
Nanoparticle Volume Fraction ◽  
Nanofluid Flow ◽  
Flow Through ◽  
Volume Method

The fluid flow and heat transfer characteristics and entropy generation of zirconia, ZrO2-water, nanofluid flow through a rectangular micro-channel are numerically investigated. The flow is considered under single-phase 3-D steady-state incompressible laminar flow conditions. The constant heat flux is applied to the bottom surface of micro-channel. The finite volume method is used to discretize the governing equations. As a result, the average Nusselt number decreases with increasing nanoparticle volume fraction, while the average Darcy friction factor is not affected. Moreover, the total entropy generation decreases with increase in nanoparticle volume fraction, while the Bejan number is almost not affected.

scholarly journals The Influence of Different Types of Nanofluid on Thermal and Fluid Flow Performance of Liquid Cold Plate

2018 ◽  
Vol 7 (4.35) ◽  
pp. 148 ◽  
Author(s):  
Nur Irmawati Om ◽  
Rozli Zulkifli ◽  
P. Gunnasegaran
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Steady State ◽  
Pressure Drop ◽  
Volume Fraction ◽  
Cold Plate ◽  
Governing Equations ◽  
Flow And Heat Transfer ◽  
Different Types ◽  
Volume Method

The influence of utilizing different nanofluids types on the liquid cold plate (LCP) is numerically investigated. The thermal and fluid flow performance of LCP is examined by using pure ethylene glycol (EG), Al2O3-EG and CuO-EG. The volume fraction of the nanoparticle for both nanofluid is 2%. The finite volume method (FVM) has been used to solved 3-D steady state, laminar flow and heat transfer governing equations. The presented results indicate that Al2O3-EG able to provide the lowest surface temperature of the heater block followed by CuO-EG and EG, respectively. It is also found that the pressure drop and friction factor are higher for Al2O3-EG and CuO-EG compared to the pure EG.

Effect of non-uniform heating on conjugate heat transfer performance for nanofluid flow in a converging duct by a two-phase Eulerian–Lagrangian method

2021 ◽  
pp. 095440892110429
Author(s):  
Md. Faizan ◽  
Sukumar Pati ◽  
Pitamber R Randive
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Volume Fraction ◽  
Constant Heat Flux ◽  
Lagrangian Model ◽  
Uniform Heating ◽  
Nanofluid Flow ◽  
Two Phase

In this paper, the effect of non-uniform heating on the conjugate thermal and hydraulic characteristics for Al2O3–water nanofluid flow through a converging duct is examined numerically. An Eulerian–Lagrangian model is employed to simulate the two-phase flow for the following range of parameters: Reynolds number (100 ≤ Re ≤ 800), nanoparticle volume fraction (0% ≤  ϕ ≤ 5%) and amplitude of the sinusoidal heat flux ( A = 0, 0.5 and 1). The results reveal a similar affinity between the applied heat flux and local Nusselt number variation qualitatively, mainly at the middle of the duct. The results also indicate that there is a considerable enhancement of Nusselt number with the increase in Reynolds number and the thermal conductivity of wall materials. In addition, increasing the particle loading contributes to an enhanced rate of heat transfer. The heat transfer rate is lower for non-uniform heating when compared with the constant heat flux and the same can be compensated by the application of volume fraction of nanoparticles

Energy Transfer Enhancement Inside an Annulus Using Gradient Porous Ribs and Nanofluids

2020 ◽  
Vol 142 (12) ◽  
Author(s):  
Hamid Reza Talesh Bahrami ◽  
Ehsan Aminian ◽  
Hamid Saffari
Keyword(s):  
Heat Transfer ◽  
Porous Media ◽  
Pressure Drop ◽  
Volume Fraction ◽  
Reynolds Numbers ◽  
Relative Height ◽  
Transfer Enhancement ◽  
Volume Fractions ◽  
Flow Reynolds Number ◽  
Maximum Volume Fraction

Abstract Porous media and nanofluid utilization are two passive heat transfer improvement tools, which have been employed extensively in recent years. Porous media with gradient properties result in both a higher effective thermal conductivity and better local convective heat transfer because of conducting the flow to the desired regions. In this study, distinct porous ribs are located on the internal border of an annulus. Four different conditions are considered for permeability change of ribs, including the minimum and maximum Darcy numbers and linearly increasing or decreasing variation in the radial direction, called LIV and LVD, respectively. In the first step, effects of porous rib relative height, porous rib porosity, and flow Reynolds number on the thermal efficiency and pressure drop are investigated. The results show that the configuration with Da = LVD and W/Rh = 0.25 has the maximum performance number PN = 2, that is the Nusselt improvement over pressure drop increment. Porous ribs arrangement with W/Rh = 0.25 and the minimum porosity (ɛ = 0.9) give the best PN. In the next step, the effects of nanoparticle addition with different volume fractions to the base fluid in different Reynolds numbers are investigated. In this step, porous rib relative height is set to W/Rh = 0.25. The results show that the maximum volume fraction has the highest heat transfer enhancement (about 2–2.5 times) but the lower volume fractions have higher PNs (PN ≈ 2.5 at ϕ = 1% and Re = 500).

scholarly journals Investigation of Forced Convection Enhancement and Entropy Generation of Nanofluid Flow through a Corrugated Minichannel Filled with a Porous Media

Entropy ◽  
2020 ◽  
Vol 22 (9) ◽  
pp. 1008
Author(s):  
Ehsan Aminian ◽  
Hesam Moghadasi ◽  
Hamid Saffari ◽  
Amir Mirza Gheitaghy
Keyword(s):  
Heat Transfer ◽  
Porous Media ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Numerical Procedure ◽  
Numerical Data ◽  
Flow In Porous Media ◽  
Geometrical Parameters ◽  
Nanofluid Flow ◽  
Flow Through

Corrugating channel wall is considered to be an efficient procedure for achieving improved heat transfer. Further enhancement can be obtained through the utilization of nanofluids and porous media with high thermal conductivity. This paper presents the effect of geometrical parameters for the determination of an appropriate configuration. Furthermore, the optimization of forced convective heat transfer and fluid/nanofluid flow through a sinusoidal wavy-channel inside a porous medium is performed through the optimization of entropy generation. The fluid flow in porous media is considered to be laminar and Darcy–Brinkman–Forchheimer model has been utilized. The obtained results were compared with the corresponding numerical data in order to ensure the accuracy and reliability of the numerical procedure. As a result, increasing the Darcy number leads to the increased portion of thermal entropy generation as well as the decreased portion of frictional entropy generation in all configurations. Moreover, configuration with wavelength of 10 mm, amplitude of 0.5 mm and phase shift of 60° was selected as an optimum geometry for further investigations on the addition of nanoparticles. Additionally, increasing trend of average Nusselt number and friction factor, besides the decreasing trend of performance evaluation criteria (PEC) index, were inferred by increasing the volume fraction of the nanofluid (Al2O3 and CuO).

scholarly journals Numerical study of the effects of geometric parameters and nanofluid properties on heat transfer and pressure drop in helical tubes

2021 ◽  
Vol 3 (8) ◽  
Author(s):  
Reza Faridi-khouzestani ◽  
Ashkan Ghafouri ◽  
Mahmood Halalizade
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Base Fluid ◽  
Volume Fraction ◽  
Geometric Parameters ◽  
Nanoparticle Diameter ◽  
Helical Coils

AbstractIn this research the geometric parameters and nanofluid properties effects on heat transfer and pressure drop in helical tube, by using alumina-water nanofluid as cooling fluid, are numerically investigated. Friction factor and heat transfer coefficient are calculated by considering the effects of nanofluid properties, including nanoparticle diameter, nanofluid temperature, Reynolds number, and volume fraction, on the one hand, and the impact of geometric parameters, including tube diameter, coils diameter and coils pitch, on the other hand. Numerical analysis is performed in the Ansys Fluent 19.2 software using the SST k-ω turbulence model. By increasing the nanofluid volume fraction the heat transfer coefficient and pressure drop in helical coils increase, the same as the nanoparticle diameter reduction. The reduction of nanoparticle diameter causes an enhancement of heat transfer and friction factor, the best results happen in dp = 5 nm and φ = 4%, where the it was ~ 40.64% more efficient than base fluid. This amounts for φ = 3%, φ = 2% and φ = 1% are 31.80%, 18.02% and 8.83%, respectively. Finally, the performance evaluation criteria (PEC) is compared for different cases, the maximum value was happen on φ = 4% and dp = 5 nm, which it is 1.86 times higher than the base fluid. The results indicate that the thermal efficiency of the heat exchanger improve largely by using helical coils and nanofluids, rather than the base fluid, and direct tubes. In addition, increasing coil pitch and curvature ratio enhance heat transfer and reduce friction factor.

Sign in / Sign up

Export Citation Format

Share Document