scholarly journals High Efficiency Buck-Boost Converter with Three Modes Selection for HV Applications using 0.18 μm Technology

2020 ◽  
Vol 18 (2) ◽  
pp. 137-144
Author(s):  
Fouad Farah ◽  
Mustapha El Alaoui ◽  
Abdelali El Boutahiri ◽  
Mounir Ouremchi ◽  
Karim El Khadiri ◽  
...  
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Output Voltage ◽  
High Efficiency ◽  
Power Conversion ◽  
Boost Converter ◽  
Current Control ◽  
Voltage Range ◽  
Operating Modes ◽  
Soft Start

In this paper, we aim to make a detailed study on the evaluation and the characteristics of the non-inverting buck–boost converter. In order to improve the behaviour of the buck-boost converter for the three operating modes, we propose an architecture based on peak current-control. Using a three modes selection circuit and a soft start circuit, this converter is able to expand the power conversion efficiency and reduce inrush current at the feedback loop. The proposed converter is designed to operate with a variable output voltage. In addition, we use LDMOS transistors with low on-resistance, which are adequate for HV applications. The obtained results show that the proposed buck-boost converter perform perfectly compared to others architecture and it is successfully implemented using 0.18 μm CMOS TSMC technology, with an output voltage regulated to 12V and input voltage range of 4-20 V. The power conversion efficiency for the three operating modes buck, boost and buck-boost are 97.6%, 96.3% and 95.5% respectively at load current of 4A.

scholarly journals DC Voltage Sensorless Predictive Control of a High-Efficiency PFC Single-Phase Rectifier Based on the Versatile Buck-Boost Converter

Sensors ◽  
2021 ◽  
Vol 21 (15) ◽  
pp. 5107
Author(s):  
Catalina González-Castaño ◽  
Carlos Restrepo ◽  
Fredy Sanz ◽  
Andrii Chub ◽  
Roberto Giral
Keyword(s):  
Power Conversion Efficiency ◽  
Real Time ◽  
Conversion Efficiency ◽  
Output Voltage ◽  
Single Phase ◽  
Power Conversion ◽  
Input Voltage ◽  
Boost Converter ◽  
Boost Converters ◽  
Grid Voltage

Many electronic power distribution systems have strong needs for highly efficient AC-DC conversion that can be satisfied by using a buck-boost converter at the core of the power factor correction (PFC) stage. These converters can regulate the input voltage in a wide range with reduced efforts compared to other solutions. As a result, buck-boost converters could potentially improve the efficiency in applications requiring DC voltages lower than the peak grid voltage. This paper compares SEPIC, noninverting, and versatile buck-boost converters as PFC single-phase rectifiers. The converters are designed for an output voltage of 200 V and an rms input voltage of 220 V at 3.2 kW. The PFC uses an inner discrete-time predictive current control loop with an output voltage regulator based on a sensorless strategy. A PLECS thermal simulation is performed to obtain the power conversion efficiency results for the buck-boost converters considered. Thermal simulations show that the versatile buck-boost (VBB) converter, currently unexplored for this application, can provide higher power conversion efficiency than SEPIC and non-inverting buck-boost converters. Finally, a hardware-in-the-loop (HIL) real-time simulation for the VBB converter is performed using a PLECS RT Box 1 device. At the same time, the proposed controller is built and then flashed to a low-cost digital signal controller (DSC), which corresponds to the Texas Instruments LAUNCHXL-F28069M evaluation board. The HIL real-time results verify the correctness of the theoretical analysis and the effectiveness of the proposed architecture to operate with high power conversion efficiency and to regulate the DC output voltage without sensing it while the sinusoidal input current is perfectly in-phase with the grid voltage.

scholarly journals A high efficiency non-inverting multi device buck-boost DC-DC converter with reduced ripple current and wide bandwidth for fuel cell low voltage applications

2018 ◽  
Vol 15 (2) ◽  
pp. 165-186
Author(s):  
Naik Venkatesh ◽  
Paulson Samuel
Keyword(s):  
Steady State ◽  
Fuel Cell ◽  
Output Voltage ◽  
High Efficiency ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Prototype Model ◽  
Voltage Range ◽  
Operating Modes

The voltage produced by the fuel cell (FC) device is unregulated and varies from 0.4 V to 0.8 V on full load to no-load respectively. When these devices are used in low voltage applications and output voltage lies between higher and lower values of input voltage range, it is required to connect a DCDC buck-boost converter to get a fixed output voltage. In this paper, a new noninverting multi device buck boost converter (MDBBC) is proposed, in which the multi device buck and boost converters are connected in cascade and operate individually either in buck or boost operating modes. The paper also includes the steady state analysis of MDDBC based on the state space averaging technique. A prototype model of proposed converter compatible with FCS-1000 Horizon FC model with rating of 270 W, 36 V is designed and developed. The proposed converter is experimentally validated with the results obtained from the prototype model, and results show the superiority of the converter with higher efficiency and lesser ripple current observed under steady state operation of the converter.

scholarly journals The role of connectivity in significant bandgap narrowing for fused-pyrene based non-fullerene acceptors toward high-efficiency organic solar cells

2020 ◽  
Vol 8 (12) ◽  
pp. 5995-6003 ◽  
Author(s):  
Shungang Liu ◽  
Wenyan Su ◽  
Xianshao Zou ◽  
Xiaoyan Du ◽  
Jiamin Cao ◽  
...  
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Organic Solar Cells ◽  
High Efficiency ◽  
Power Conversion ◽  
Structural Isomer ◽  
Bandgap Narrowing ◽  
Higher Power

Isomers of non-fullerene acceptors with pyrene as cores but fused at different positions were studied. FPIC6 possessed ∼119 nm of red-shift absorption and much higher power conversion efficiency of 11.55% as compared to its structural isomer FPIC5.

Trendsetters in High‐Efficiency Organic Solar Cells: Toward 20% Power Conversion Efficiency

Solar RRL ◽  
2019 ◽  
Vol 4 (1) ◽  
pp. 1900342 ◽  
Author(s):  
Mushfika Baishakhi Upama ◽  
Md Arafat Mahmud ◽  
Gavin Conibeer ◽  
Ashraf Uddin
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Organic Solar Cells ◽  
High Efficiency ◽  
Power Conversion

scholarly journals A Review on Improving the Quality of Perovskite Films in Perovskite Solar Cells via the Weak Forces Induced by Additives

2019 ◽  
Vol 9 (20) ◽  
pp. 4393 ◽  
Author(s):  
Jien Yang ◽  
Songhua Chen ◽  
Jinjin Xu ◽  
Qiong Zhang ◽  
Hairui Liu ◽  
...  
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
High Efficiency ◽  
Power Conversion ◽  
Perovskite Solar Cells ◽  
Term Stability ◽  
Long Term Stability ◽  
Weak Forces

Perovskite solar cells (PSCs) employing organic-inorganic halide perovskite as active layers have attracted the interesting of many scientists since 2009. The power conversion efficiency (PCE) have pushed certified 25.2% in 2019 from initial 3.81% in 2009, which is much faster than that of any type of solar cell. In the process of optimization, many innovative approaches to improve the morphology of perovskite films were developed, aiming at elevate the power conversion efficiency of perovskite solar cells (PSCs) as well as long-term stability. In the context of PSCs research, the perovskite precursor solutions modified with different additives have been extensively studied, with remarkable progress in improving the whole performance. In this comprehensive review, we focus on the forces induced by additives between the cations and anions of perovskite precursor, such as hydrogen bonds, coordination or some by-product (e.g., mesophase), which will lead to form intermediate adduct phases and then can be converted into high quality films. A compact uniform perovskite films can not only upgrade the power conversion efficiency (PCE) of devices but also improve the stability of PSCs under ambient conditions. Therefore, strategies for the implementation of additives engineering in perovskites precursor solution will be critical for the future development of PSCs. How to manipulate the weak forces in the fabrication of perovskite film could help to further develop high-efficiency solar cells with long-term stability and enable the potential of future practical applications.

Vivid-colored silicon solar panels with high efficiency and non-iridescent appearance

2019 ◽  
Vol 4 (4) ◽  
pp. 874-880 ◽  
Author(s):  
Chengang Ji ◽  
Zhong Zhang ◽  
Taizo Masuda ◽  
Yuki Kudo ◽  
L. Jay Guo
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
High Power ◽  
High Efficiency ◽  
Power Conversion ◽  
Solar Panels ◽  
High Power Conversion Efficiency ◽  
Novel Approach

A novel approach was proposed for fabricating bright-colored solar cells with high power conversion efficiency and excellent angular insensitivity.

A high efficiency solution processed polymer inverted triple-junction solar cell exhibiting a power conversion efficiency of 11.83%

2015 ◽  
Vol 8 (1) ◽  
pp. 303-316 ◽  
Author(s):  
Abd. Rashid bin Mohd Yusoff ◽  
Dongcheon Kim ◽  
Hyeong Pil Kim ◽  
Fabio Kurt Shneider ◽  
Wilson Jose da Silva ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Triple Junction ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Power Conversion ◽  
Open Circuit ◽  
Tandem Solar Cells

We propose that 1 + 1 + 1 triple-junction solar cells can provide an increased efficiency, as well as a higher open circuit voltage, compared to tandem solar cells.

scholarly journals Miniature DC-DC Boost Converter for Driving Display Panel of Notebook Computer

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2924
Author(s):  
Seok-Hyeong Ham ◽  
Hyung-Jin Choe
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Power Conversion ◽  
Input Voltage ◽  
Boost Converter ◽  
Switching Frequency ◽  
Notebook Computer ◽  
Switching Losses ◽  
Voltage Stress ◽  
Switch Temperature

This paper proposes a miniature DC-DC boost converter to drive the display panel of a notebook computer. To reduce the size of the circuit, the converter was designed to operate at a switching frequency of 1 MHz. The power conversion efficiency improved using a passive snubber circuit that consisted of one inductor, two capacitors, and two diodes; it reduced the switching losses by lowering the voltage stress of the switch and increased the voltage gain using charge pumping operations. An experimental converter was fabricated at 2.5 cm × 1 cm size using small components, and tested at input voltage 5 V ≤ VIN ≤ 17.5 V and output current 30 mA ≤ IO ≤ 150 mA. Compared to existing boost converters, the proposed converter had ~7.8% higher power conversion efficiency over the entire range of VIN and IO, only ~50% as much voltage stress of the switch and diodes, and a much lower switch temperature TSW = 49.5 °C. These results indicate that the proposed converter is a strong candidate for driving the display panel of a notebook computer.

scholarly journals Triple-cation low-bandgap perovskite thin-films for high-efficiency four-terminal all-perovskite tandem solar cells

2020 ◽  
Vol 8 (46) ◽  
pp. 24608-24619 ◽  
Author(s):  
Somayeh Moghadamzadeh ◽  
Ihteaz M. Hossain ◽  
The Duong ◽  
Saba Gharibzadeh ◽  
Tobias Abzieher ◽  
...  
Keyword(s):  
Thin Films ◽  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
High Efficiency ◽  
Power Conversion ◽  
Perovskite Solar Cells ◽  
Tandem Solar Cells ◽  
Low Bandgap ◽  
Photo Stability

Incorporating 2.5% Cs in FA0.8MA0.2Sn0.5Pb0.5I3 improves the photo-stability of the low-bandgap perovskite solar cells. The champion device with power conversion efficiency of 18.9% maintain 92% of its initial efficiency after 120 min MPP tracking.

Sign in / Sign up

Export Citation Format

Share Document