scholarly journals DC Voltage Sensorless Predictive Control of a High-Efficiency PFC Single-Phase Rectifier Based on the Versatile Buck-Boost Converter

Sensors ◽  
2021 ◽  
Vol 21 (15) ◽  
pp. 5107
Author(s):  
Catalina González-Castaño ◽  
Carlos Restrepo ◽  
Fredy Sanz ◽  
Andrii Chub ◽  
Roberto Giral
Keyword(s):  
Power Conversion Efficiency ◽  
Real Time ◽  
Conversion Efficiency ◽  
Output Voltage ◽  
Single Phase ◽  
Power Conversion ◽  
Input Voltage ◽  
Boost Converter ◽  
Boost Converters ◽  
Grid Voltage

Many electronic power distribution systems have strong needs for highly efficient AC-DC conversion that can be satisfied by using a buck-boost converter at the core of the power factor correction (PFC) stage. These converters can regulate the input voltage in a wide range with reduced efforts compared to other solutions. As a result, buck-boost converters could potentially improve the efficiency in applications requiring DC voltages lower than the peak grid voltage. This paper compares SEPIC, noninverting, and versatile buck-boost converters as PFC single-phase rectifiers. The converters are designed for an output voltage of 200 V and an rms input voltage of 220 V at 3.2 kW. The PFC uses an inner discrete-time predictive current control loop with an output voltage regulator based on a sensorless strategy. A PLECS thermal simulation is performed to obtain the power conversion efficiency results for the buck-boost converters considered. Thermal simulations show that the versatile buck-boost (VBB) converter, currently unexplored for this application, can provide higher power conversion efficiency than SEPIC and non-inverting buck-boost converters. Finally, a hardware-in-the-loop (HIL) real-time simulation for the VBB converter is performed using a PLECS RT Box 1 device. At the same time, the proposed controller is built and then flashed to a low-cost digital signal controller (DSC), which corresponds to the Texas Instruments LAUNCHXL-F28069M evaluation board. The HIL real-time results verify the correctness of the theoretical analysis and the effectiveness of the proposed architecture to operate with high power conversion efficiency and to regulate the DC output voltage without sensing it while the sinusoidal input current is perfectly in-phase with the grid voltage.

scholarly journals High Efficiency Buck-Boost Converter with Three Modes Selection for HV Applications using 0.18 μm Technology

2020 ◽  
Vol 18 (2) ◽  
pp. 137-144
Author(s):  
Fouad Farah ◽  
Mustapha El Alaoui ◽  
Abdelali El Boutahiri ◽  
Mounir Ouremchi ◽  
Karim El Khadiri ◽  
...  
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Output Voltage ◽  
High Efficiency ◽  
Power Conversion ◽  
Boost Converter ◽  
Current Control ◽  
Voltage Range ◽  
Operating Modes ◽  
Soft Start

In this paper, we aim to make a detailed study on the evaluation and the characteristics of the non-inverting buck–boost converter. In order to improve the behaviour of the buck-boost converter for the three operating modes, we propose an architecture based on peak current-control. Using a three modes selection circuit and a soft start circuit, this converter is able to expand the power conversion efficiency and reduce inrush current at the feedback loop. The proposed converter is designed to operate with a variable output voltage. In addition, we use LDMOS transistors with low on-resistance, which are adequate for HV applications. The obtained results show that the proposed buck-boost converter perform perfectly compared to others architecture and it is successfully implemented using 0.18 μm CMOS TSMC technology, with an output voltage regulated to 12V and input voltage range of 4-20 V. The power conversion efficiency for the three operating modes buck, boost and buck-boost are 97.6%, 96.3% and 95.5% respectively at load current of 4A.

scholarly journals Miniature DC-DC Boost Converter for Driving Display Panel of Notebook Computer

Energies ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2924
Author(s):  
Seok-Hyeong Ham ◽  
Hyung-Jin Choe
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Power Conversion ◽  
Input Voltage ◽  
Boost Converter ◽  
Switching Frequency ◽  
Notebook Computer ◽  
Switching Losses ◽  
Voltage Stress ◽  
Switch Temperature

This paper proposes a miniature DC-DC boost converter to drive the display panel of a notebook computer. To reduce the size of the circuit, the converter was designed to operate at a switching frequency of 1 MHz. The power conversion efficiency improved using a passive snubber circuit that consisted of one inductor, two capacitors, and two diodes; it reduced the switching losses by lowering the voltage stress of the switch and increased the voltage gain using charge pumping operations. An experimental converter was fabricated at 2.5 cm × 1 cm size using small components, and tested at input voltage 5 V ≤ VIN ≤ 17.5 V and output current 30 mA ≤ IO ≤ 150 mA. Compared to existing boost converters, the proposed converter had ~7.8% higher power conversion efficiency over the entire range of VIN and IO, only ~50% as much voltage stress of the switch and diodes, and a much lower switch temperature TSW = 49.5 °C. These results indicate that the proposed converter is a strong candidate for driving the display panel of a notebook computer.

Observer-Based Power Management for Multi-Source Electric Vehicles Using Optimized Splitting Ratios

2018 ◽  
Author(s):  
Ahmed M. Ali ◽  
Dirk Söffker
Keyword(s):  
Power Conversion Efficiency ◽  
Real Time ◽  
Power Management ◽  
Conversion Efficiency ◽  
Electric Vehicles ◽  
Control Method ◽  
Power Conversion ◽  
Observer Design ◽  
Power Handling ◽  
Optimal Power

Optimal power management in real-time is a core technology of hybrid electric vehicles (HEVs). The online application of optimized power split ratios based on driver demand is a promising approach allowing near optimal power handling decisions in real-time. However, the fulfillment of exact power delivery (driveability) is an open challenge of this approach due to interpolation of driver’s demand to the optimized discrete solutions. Finding balanced power management that handles unscheduled loads and sustains required power conversion efficiency may significantly improve the experimental application of this approach. This work proposes an observer-based control method integrated to the power management system that ensures better driveability with minimal effect on power handling optimality. Modeling of traction system for observer design is based on a simplified brushless DC motor model. Identification of system parameters is achieved by a newly introduced error minimization algorithm using NSGA-II to obtain the same dynamic response as the original system. Results analysis shows 7% reduction of power consumption and 98% improvement of driveability at minimal mitigation of power conversion efficiency.

Improvement of Power-Conversion Efficiency of AC–DC Boost Converter Using 1:1 Transformer

2018 ◽  
Vol 33 (8) ◽  
pp. 6646-6655 ◽  
Author(s):  
Seok-Hyeong Ham ◽  
Hyung-Jin Choe ◽  
Hyeon-Seok Lee ◽  
Bongkoo Kang
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Power Conversion ◽  
Boost Converter

scholarly journals Optimization of Charge Pump Based on Piecewise Modeling of Output-Voltage Ripple

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4809
Author(s):  
Yajun Lin ◽  
Jianxin Yang ◽  
Tin-Wai Mui ◽  
Yong Zhou ◽  
Ka-Nang Leung
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Output Voltage ◽  
Power Conversion ◽  
Charge Pump ◽  
Switching Frequency ◽  
Linear Charge ◽  
Voltage Ripple ◽  
Accurate Design ◽  
Charge Pump Circuit

This work proposes a piecewise modeling of output-voltage ripple for linear charge pumps. The proposed modeling can obtain a more accurate design expression of power-conversion efficiency. The relationship between flying and output capacitance, as well as switching frequency and optimize power-conversion efficiency can be calculated. The proposed modeling is applied to three charge-pump circuits: 1-stage linear charge pump, dual-branch 1-stage linear charge pump and 4× cross-coupled charge pump. Circuit-level simulation is used to verify the accuracy of proposed modeling.

scholarly journals Performance Improvement of PWM Control Methods for Voltage Step-Down in Series Resonant DC–DC Converters

Energies ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 4569
Author(s):  
Vadim Sidorov ◽  
Andrii Chub ◽  
Dmitri Vinnikov
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Pulse Width Modulation ◽  
Renewable Energy Sources ◽  
Power Conversion ◽  
Input Voltage ◽  
Voltage Regulation ◽  
Switching Frequency ◽  
Semiconductor Switches ◽  
Series Resonant

The paper is focused on galvanically isolated series resonant DC–DC converters (SRCs) with a low quality factor of the resonant tank. These converters provide input voltage regulation at fixed switching frequency and good power density. Different modulation methods at the fixed switching frequency enable the implementation of the voltage buck functionality in these converters. The SRC under study is considered as a step-up front-end DC–DC converter for the integration of renewable energy sources in DC microgrids. The paper evaluates the voltage buck performance of the SRC achieved by using different pulse-width modulation (PWM) methods including conventional PWM and shifted PWM. Moreover, the new PWM methods, i.e., the hybrid shifted PWM (HSPWM), improved shifted PWM (ISPWM), and hybrid PWM (HPWM), are proposed to overcome the disadvantages of the existing methods. They improve the power conversion efficiency in the buck mode by reducing the power losses in the semiconductor switches and the isolating transformer of the SRC. The proposed and the existing methods are benchmarked in terms of the components stresses and power conversion efficiency. The presented findings have been experimentally validated by the help of a 200 W prototype, which demonstrated the lowest power loss in the case of the HPWM.

A Study on 3-phase Interleaved DC-DC Boost Converter Structure and Operation for Input Current Stress Reduction

2017 ◽  
Vol 8 (4) ◽  
pp. 1948
Author(s):  
M. A. Harimon ◽  
A. Ponniran ◽  
A. N. Kasiran ◽  
H. H. Hamzah
Keyword(s):  
Stress Reduction ◽  
Output Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Input Current ◽  
High Input ◽  
Boost Converters ◽  
Current Stress ◽  
Conduction Mode ◽  
Interleaving Technique

This paper analyses a 3-phase interleaved DC-DC boost converter for the conversion of low input voltage with high input current to higher DC output voltage. The operation of the 3-phase interleaved DC-DC boost converter with multi-parallel of boost converters is controlled by interleaved of switching signals with 120 degrees phase-shifted. Therefore, with this circuit configuraion, high input current is evenly shared among the parallel units and consequently the current stress is reduced on the circuit and semiconductor devices and contributes reduction of overall losses. The simulation and hardware results show that the current stress and the semiconductor conduction losses were reduced approximately 33% and 32%, respectively in the 3-phase interleaved DC-DC boost converter compared to the conventional DC-DC boost converters. Furthermore, the use of interleaving technique with continuous conduction mode on DC-DC boost converters is reducing input current and output voltage ripples to increase reliability and efficiency of boost converters.

Improvement of Power-Conversion Efficiency of a DC–DC Boost Converter Using a Passive Snubber Circuit

2012 ◽  
Vol 59 (4) ◽  
pp. 1808-1814 ◽  
Author(s):  
Jae-Jung Yun ◽  
Hyung-Jin Choe ◽  
Young-Ho Hwang ◽  
Yong-Kyu Park ◽  
Bongkoo Kang
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Power Conversion ◽  
Boost Converter ◽  
Snubber Circuit

scholarly journals A High Power-Conversion-Efficiency Voltage Boost Converter with MPPT for Wireless Sensor Nodes

Sensors ◽  
2021 ◽  
Vol 21 (16) ◽  
pp. 5447
Author(s):  
Xiwen Zhu ◽  
Qiang Fu ◽  
Ruimo Yang ◽  
Yufeng Zhang
Keyword(s):  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
High Power ◽  
Power Conversion ◽  
Boost Converter ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
High Power Conversion Efficiency ◽  
Wireless Sensor Nodes ◽  
Pv Cell

A high power-conversion-efficiency voltage boost converter with MPPT for wireless sensor nodes (WSNs) is proposed in this paper. Since tiny wireless sensor nodes are all over complex environments, an efficient power management system (PMS) must be equipped to achieve long-term self-power supply and maintain regular operation. It is common to use Photovoltaic cells (PV) to harvest sunlight in the environment. However, most existing interface boost integrated circuits for the PV cell have low efficiency. This paper presents a voltage boost converter (VBC) with high power conversion efficiency (PCE) for WSNs. The integrated circuit (IC) designed in this paper includes a novel four-phase high-efficiency charge pump module, an ultra-low-power perturbation observation (P&O) MPPT control circuit module, a feedback control module, a nano-ampere current reference, etc. Manufactured in a standard 0.35 um complementary metal-oxide-semiconductor (CMOS) technology, the chip area is 3.15 mm × 2.43 mm. Test results demonstrate that when the output voltage of the PV cell is more than 0.5 V, VBC can improve the voltage to 3Vin, and the calculated voltage conversion efficiency can reach 99.4%. P&O MPPT algorithm makes output power improving 8.53%. Furthermore, when the output load current is 297uA, the output PCE achieves 85.1%.

A thiourea additive-based quadruple cation lead halide perovskite with an ultra-large grain size for efficient perovskite solar cells

Nanoscale ◽  
2019 ◽  
Vol 11 (45) ◽  
pp. 21824-21833 ◽  
Author(s):  
Jyoti V. Patil ◽  
Sawanta S. Mali ◽  
Chang Kook Hong
Keyword(s):  
Thin Films ◽  
Grain Size ◽  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Power Conversion ◽  
Perovskite Solar Cells ◽  
Inorganic Perovskite ◽  
Halide Perovskite ◽  
Lead Halide

Controlling the grain size of the organic–inorganic perovskite thin films using thiourea additives now crossing 2 μm size with >20% power conversion efficiency.

Sign in / Sign up

Export Citation Format

Share Document