Novel Boron Microalloyed Steel Used for High-power Wind Turbine Yaw Bearing Rings and Corresponding Simulation of Heat Treatment Process

2015 ◽  
Vol 51 (14) ◽  
pp. 29 ◽  
Author(s):  
Chen CHEN
Keyword(s):  
Heat Treatment ◽  
Wind Turbine ◽  
High Power ◽  
Treatment Process ◽  
Microalloyed Steel ◽  
Heat Treatment Process ◽  
Yaw Bearing ◽  
Bearing Rings

Experimental Investigation of Residual Stresses after Heat Treatment and Grinding Processes in the Production of Ball Bearing Rings

2008 ◽  
Vol 571-572 ◽  
pp. 27-32 ◽  
Author(s):  
Volkan Güley ◽  
A. Erman Tekkaya ◽  
Turhan Savaş ◽  
Feridun Özhan
Keyword(s):  
Heat Treatment ◽  
Experimental Investigation ◽  
Residual Stresses ◽  
Process Parameters ◽  
Treatment Process ◽  
Ball Bearing ◽  
Grinding Process ◽  
Heat Treatment Process ◽  
Grinding Processes ◽  
Bearing Rings

Experimental investigation of residual stresses after heat treatment and grinding processes in the production of ball bearing rings has been carried out. The residual stresses were measured by X-ray diffraction method utilizing chromium radiation, which has an average penetration depth of 5 μm incident on 100Cr6 (AISI-E52100) ball bearing steel. The process parameters of heat treatment and grinding processes were varied so as to represent the extreme values that can be applied in the respective processes. Hardness and percent retained austenite limit the heat treatment process parameters; while roundness, surface roughness and form the grinding process. Tensile surface residual stresses on the raceway of ball bearing rings changes to compression after grinding in both circumferential and axial directions. In grinding relatively higher compressive stresses were measured in axial direction compared to the circumferential direction. This experimental investigation also showed that the influence of heat treatment process parameters on the magnitude and distribution of residual stresses survived even after grinding process; i.e. heat treatment and grinding processes cannot be evaluated independently in process design for favourable residual stresses.

Characterization of Microstructure and Mechanical Properties of a Nb-Microalloyed Steel after Quenching-Partitioning-Tempering Process

2010 ◽  
Vol 654-656 ◽  
pp. 90-93 ◽  
Author(s):  
Xiao Dong Wang ◽  
Zheng Hong Guo ◽  
Yong Hua Rong
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Heat Treatment ◽  
Treatment Process ◽  
Microalloyed Steel ◽  
Heat Treatment Process ◽  
Step Process ◽  
Transmission Electron ◽  
Nb Microalloyed Steel ◽  
Tempering Process

A novel heat treatment process, that is, quenching-partitioning-tempering (Q-P-T) process, has been developed as a new way to obtain ultrahigh strength martensitic structural steel containing retained austenite and alloying carbide. In order to display merit of the Q-P-T process, a medium carbon Nb-microalloyed steel is treated by Q-P-T 1-step process and Q-P-T 2-step process, as well as treated by the transformation induced plasticity heat treatment process and quenching and tempering process, respectively. The results show that Q-P-T samples possess better mechanical properties than those treated by other heat treatment processes. The origin of the good mechanical properties is analyzed based on the phase and microstructure characterization using X-ray diffraction, scanning electron microscopy and transmission electron microscopy.

Optimization of Heat Treatment Process of ZE41A Magnesium Alloy Using Grey- Based Taguchi Method

2008 ◽  
Vol 3 (2) ◽  
pp. 63-69
Author(s):  
M. Sivapragash ◽  
◽  
V. Sateeshkumar ◽  
P.R. Lakshminarayanan ◽  
R. Karthikeyan ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Magnesium Alloy ◽  
Taguchi Method ◽  
Treatment Process ◽  
Heat Treatment Process

EFFECT ON HARDNESS and MICRO STRUCTURAL BEHAVIOUR OF TOOL STEEL AFTER HEAT TREATMENT PROCESS

2017 ◽  
Vol 4 (24) ◽  
Author(s):  
Karanbir Singh ◽  
Aditya Chhabra ◽  
Vaibhav Kapoor ◽  
Vaibhav Kapoor
Keyword(s):  
Heat Treatment ◽  
Empirical Study ◽  
Tool Steel ◽  
Treatment Process ◽  
Heat Treatment Process ◽  
Structural Behaviour ◽  
Treatment Processes ◽  
En 31

This study is conducted to analyze the effect on the Hardness and Micro Structural Behaviour of three Sample Grades of Tool Steel i.e. EN-31, EN-8, and D3 after Heat Treatment Processes Such As Annealing, Normalizing, and Hardening and Tempering. The purpose of Selecting Tool Steel is Because Tool Steel is Mostly Used in the Manufacturing Industry.This study is based upon the empirical study which means it is derived from experiment and observation rather than theory.

Failure Analysis on a Counterweight Assembly of an Aeroengine

2011 ◽  
Vol 339 ◽  
pp. 342-348
Author(s):  
Hai Jun Tang ◽  
Hong Yu Yao
Keyword(s):  
Heat Treatment ◽  
Stress Concentration ◽  
Failure Analysis ◽  
Failure Mechanism ◽  
Treatment Process ◽  
Hardness Test ◽  
Heat Treatment Process ◽  
Material Loss ◽  
Structure Strength ◽  
Crucial Part

The paper presents a failure analysis on a counterweight assembly installed on crank shaft which resulted in an in-flight shutdown of a piston aeroengine. The counterweight assembly failure includes counterweight block material loss and fractured washer which is the most crucial part for in-flight shutdown in this type of aeroengine. Macro observation, fractography analysis, metallography analysis and hardness test were conducted on the failed counterweight assembly. The result shows that failure mechanism of counterweight block and washer is fatigue. The washer failure is likely due to inappropriate heat treatment process and continuous impact in flight by slightly tilted roller. Counterweight material loss is attributed to stress concentration, low structure strength and impact came from the tilted roller. Finally some safety suggestion on design and maintenance is given.

Relationship of Microstructure and Mechanical Properties in Er-Containing Aluminum Alloy

2015 ◽  
Vol 1120-1121 ◽  
pp. 1109-1114
Author(s):  
Xin Lei ◽  
Hui Huang ◽  
S.P. Wen
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
Treatment Process ◽  
Mg Alloys ◽  
The Other ◽  
Heat Treatment Process ◽  
Comprehensive Performance ◽  
Relationship Of ◽  
Al Mg Alloys

This study investigated the mechanical properties and microstructures of Er-containing Al–Mg alloys. The research found that the H114-T sheet of Er-containing Al–Mg alloys showed a relative good comprehensive performance in mechanical properties. With the special rolling and heat treatment process, this H114-T sheet showed different morphology of microstructures with the other sheets in Er-containing Al–Mg alloys. Grains in H114-T sheet performed irregular shape polygon, a number of subgrains appeared in grains, the amount of dislocations in grains decreased. H114-T sheet possessed a lot of Copper texture, this may be one of important factors influenced the mechanical properties.

Network Carbide Inheritance during Heat Treatment Process of Large Shield Machine Bearing Steel GCr15SiMn

2015 ◽  
Vol 817 ◽  
pp. 115-120 ◽  
Author(s):  
Dan Zhang ◽  
Le Yu Zhou ◽  
Chao Lei Zhang ◽  
Chao Huang ◽  
Min Zhao ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Treatment Process ◽  
Bearing Steel ◽  
Treatment Temperature ◽  
Heat Treatment Process ◽  
Soaking Time ◽  
Hot Rolled ◽  
Chinese Standard ◽  
Shield Machine ◽  
Quenching And Tempering

Network carbide inheritance during heat treatment process of large shield machine bearing steel GCr15SiMn was investigated by heat treatment experiments and quantitative metallographic. Samples with the proeutectoid cementite network thickness in the range of 0.19~0.54 μm were obtained by changing austenitizing temperature and soaking time of pearlite transformation. The results show that the network in hot rolled bar can be improved when the pre-heat treatment temperature is 950 °C. When the network thickness is above 0.40 μm, the undissolved cementite networks present in microstructures after quenching and tempering. In a Chinese standard, the network grades are 1.5 and 3.0 degree when the networks thickness are 0.40 μm and 0.54 μm, respectively. The critical network thickness that can be eliminated by heat treatment is 0.29 μm.

Sign in / Sign up

Export Citation Format

Share Document