Properties of Environmental Friendly Concrete Containing Recycled Coarse Aggregate and Fly Ash

2013 ◽  
Vol 368-370 ◽  
pp. 957-962
Author(s):  
Xiao Shuang Shi ◽  
Qing Yuan Wand ◽  
Lang Li ◽  
Tao Long
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Compressive Strength ◽  
Coarse Aggregate ◽  
Recycled Concrete ◽  
Reaction Products ◽  
X Ray ◽  
Transition Zones ◽  
Environmental Friendly ◽  
Scanning Electron

Six mixtures with different ratios (0%, 50% and 100%) were designed to investigate the compressive strength, elastic modulus and Poissons ratio of geopolymeric recycled concrete (GRC). The mechanical properties and failure mechanism of recycled concrete (RAC) and GRC were tested and discussed by scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDX). The results show that, GRC concretes are stronger than RAC concretes due to different reaction products and better microstructure in interfacial transition zones (ITZs). The EDX results show that the higher compressive strength with higher Si/Al ratio.

UTILIZATION OF FLY ASH AND CONCRETE RESIDUE IN THE PRODUCTION OF GEOPOLYMER BRICKS

2017 ◽  
Vol 12 (1) ◽  
pp. 63-77 ◽  
Author(s):  
Siriporn Sirikingkaew ◽  
Nuta Supakata
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Phase Composition ◽  
Fly Ash ◽  
Industrial Waste ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

This study presents the development of geopolymer bricks synthetized from industrial waste, including fly ash mixed with concrete residue containing aluminosilicate compound. The above two ingredients are mixed according to five ratios: 100:0, 95:5, 90:10, 85:15, and 80:20. The mixture's physico-mechanical properties, in terms of water absorption and the compressive strength of the geopolymer bricks, are investigated according to the TIS 168-2546 standard. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses are used to investigate the microstructure and the elemental and phase composition of the brick specimens. The results indicate that the combination of fly ash and concrete residue represents a suitable approach to brick production, as required by the TIS 168–2546 standard.

scholarly journals Compressive strength and microstructure of modified coffee exocarp cement-based composites

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 9059-9074
Author(s):  
Zehua Zhu ◽  
Cheng Cheng ◽  
Debin Zhu ◽  
Dewen Liu ◽  
Yafei Zhang
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Portland Cement ◽  
Vacuum Extraction ◽  
X Ray Diffraction ◽  
Extraction Technology ◽  
X Ray ◽  
Scanning Electron

Portland cement-based composites were prepared with coffee exocarp (pretreated with water or NaOH) via vacuum extraction technology. An orthogonal test was adopted to analyze the influence of various factors on mechanical properties of the composite. The morphology and composition of the pretreated coffee exocarp and composites were analyzed via environmental scanning electron microscopy and X-ray diffraction, respectively. The results showed that the coffee exocarp content and vacuum extraction time significantly affected the compressive strength. An addition of 10% coffee exocarp had a slight negative effect on the mechanical properties but enhanced the crack inhibition and overall toughness of the composite. The scanning electron microscopy and X-ray diffraction results showed that the composite containing coffee exocarp pretreated with 4% NaOH solution had the highest density and exhibited the best properties due to mechanical interlocking between the coffee exocarp and cement. After 28 d of curing, the composites exhibited a maximum compressive strength of 15.72 MPa, a mass that was approximately 37% less than that of ordinary Portland cement samples, and a bulk density of 1.5 g/cm3 to 1.6 g/cm3. Hence, the produced biocomposites could be used for low-load pavements, providing a new type of economical building material.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Al2O3-TiC-ZrO2 Ceramic Composites

2012 ◽  
Vol 476-478 ◽  
pp. 1031-1035
Author(s):  
Wei Min Liu ◽  
Xing Ai ◽  
Jun Zhao ◽  
Yong Hui Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Ceramic Composites ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

Al2O3-TiC-ZrO2ceramic composites (ATZ) were fabricated by hot-pressed sintering. The phases and microstructure of the composites were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The relative density and mechanical properties (flexural strength, fracture toughness and Vicker’s hardness) of the composites were tested. The results show that the microstructure of the composites was the gray core-white rim. With the increase of sintering temperature, the relative density and mechanical properties of the composites increased first and then decreased. The composite sintered at 1705°C has the highest synthetical properties, and its relative density, flexural strength, fracture toughness and Vickers hardness are 98.3%,970MPa,6.0 MPa•m1/2and 20.5GPa, respectively.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

Influence of Fly Ash on Corrosion Resistance of Refractory Forsterite-Spinel Ceramics

2021 ◽  
Vol 325 ◽  
pp. 181-187
Author(s):  
Martin Nguyen ◽  
Radomír Sokolář
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Corrosion Resistance ◽  
Fly Ash ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transition Zones ◽  
Refractory Ceramics ◽  
Scanning Electron

This article examines the influence of fly ash on corrosion resistance of refractory forsterite-spinel ceramics by molten iron as a corrosive medium. Fly ash in comparison with alumina were used as raw materials and sources of aluminium oxide for synthesis of forsterite-spinel refractory ceramics. Raw materials were milled, mixed in different ratios into two sets of mixtures and sintered at 1550°C for 2 hours. Samples were characterized by X-ray diffraction analysis and thermal dilatometric analysis. Crucibles were then made from the fired ceramic mixtures and fired together with iron at its melting point of 1535°C for 5 hours. The corrosion resistance was evaluated by scanning electron microscopy on the transition zones between iron and ceramics. Mixtures with increased amount of spinel had higher corrosion resistance and mixtures with fly ash were comparable to mixtures with alumina in terms of corrosion resistance and refractory properties.

scholarly journals Valorization of Brick and Glass CDWs for the Development of Geopolymers Containing More Than 80% of Wastes

Minerals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 672
Author(s):  
Dimitris Kioupis ◽  
Aggeliki Skaropoulou ◽  
Sotirios Tsivilis ◽  
Glikeria Kakali
Keyword(s):  
Electron Microscopy ◽  
Compressive Strength ◽  
Circular Economy ◽  
X Ray Diffraction ◽  
Glass Waste ◽  
X Ray ◽  
Optimum Synthesis ◽  
Synthesis Parameters ◽  
Construction And Demolition Wastes ◽  
Scanning Electron

One of the areas of priority in a circular economy, regarding waste management, regards the valorization of construction and demolition wastes (CDW). This study suggests the synthesis of geopolymeric binders based almost entirely on construction and demolition wastes. Ceramic waste was used as the aluminosilicate precursor of the geopolymer synthesis, while glass waste was applied in the preparation of the activation solution. A fractional experimental design defined the optimum synthesis parameters, based on compressive strength values. The final products were characterized by means of X-Ray Diffraction (XRD), Fourier-Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM). The glass waste was appropriately processed in order to prepare the activation solution for the geopolymerization of brick waste. In this work, CDW-based geopolymers were produced with a compressive strength in the range 10–44 MPa. The developed products contained 80–90 wt.% CDWs, depending on the method of activator preparation.

scholarly journals Effects on Mechanical Properties of Recycled PET in Cement-Based Composites

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Liliana Ávila Córdoba ◽  
Gonzalo Martínez-Barrera ◽  
Carlos Barrera Díaz ◽  
Fernando Ureña Nuñez ◽  
Alejandro Loza Yañez
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Compressive Strength ◽  
Compressive Strain ◽  
Young Modulus ◽  
Silica Sand ◽  
Chemical Compositions ◽  
Particle Sizes ◽  
Recycled Pet ◽  
Scanning Electron

Concretes consisting of portland cement (OPC), silica sand, gravel, water, and recycled PET particles were developed. Specimens without PET particles were prepared for comparison. Curing times, PET particle sizes, and aggregate concentrations were varied. The compressive strength, compressive strain at yield point, and Young modulus were determined. Morphological and chemical compositions of recycled PET particles were seen in a scanning electron microscopy. Results show that smaller PET particle sizes in lower concentrations generate improvements on compressive strength and strain, and Young’s modulus decreases when the size of PET particles used was increased.

scholarly journals Microstructural and Mechanical Properties of Alkali Activated Materials from Two Types of Blast Furnace Slags

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2089 ◽  
Author(s):  
Jun Xing ◽  
Yingliang Zhao ◽  
Jingping Qiu ◽  
Xiaogang Sun
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Blast Furnace ◽  
Thermal Stabilization ◽  
Hydration Process ◽  
Reaction Products ◽  
Basic Oxide ◽  
X Ray ◽  
Physical And Chemical ◽  
Alkali Activated

This paper investigated the effect of blast furnace slags (BFS) characteristics on the properties achievement after being alkali activated. The physical and chemical characteristics of BFS were determined by X-ray fluorescence (XRF), X-ray Diffraction (XRD) and laser granulometry. Multi-technical characterizations using calorimetry, XRD, Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetry (TG-DTG), scanning electron microscope (SEM), nitrogen sorption and uniaxial compressive strength (UCS) were applied to give an in-depth understanding of the relationship between the reaction products, microstructure and BFS characteristics. The test results show that the microstructure and mechanical properties of alkali activated blast furnace slags (BFS) highly depend on the characteristics of BFS. Although the higher content of basic oxide could accelerate the hydration process and result in higher mechanical properties, a poor thermal stabilization was observed. On the other hand, with a higher content of Fe, the hydration process in alkali activated BFS2 lasts for a longer time, contributing to a delayed compressive strength achievement.

scholarly journals Amazonian Metakaolin Reactivity for Geopolymer Synthesis

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
Ruy A. Sá Ribeiro ◽  
Marilene G. Sá Ribeiro ◽  
Gregory P. Kutyla ◽  
Waltraud M. Kriven
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
X Ray Diffraction ◽  
Local Resource ◽  
X Ray ◽  
Potassium Sodium ◽  
Mixing Intensity ◽  
Amazonian Region ◽  
Scanning Electron

To determine the viability of using a local resource for geopolymer synthesis, geopolymers were synthesized using metakaolin made from clay mined in the Amazonian region of Brazil. Samples were made with mixed potassium-sodium and pure sodium metakaolin-based geopolymer. Samples were also made using commercial metakaolin (CMK) from BASF, Inc. as a comparison to the Amazonian metakaolin (AMK). Scanning electron microscopy was used to investigate the microstructure of the materials. X-ray diffraction was able to confirm the formation of geopolymer. The mechanical properties of AMK material were nearly equivalent to those based on CMK. Neither CMK nor AMK reacted completely, although samples made with CMK showed less unreacted material. By increasing the mixing intensity and duration, the amount of residual unreacted material was substantially reduced, and mechanical properties were improved.

SYNERGISTIC REINFORCEMENT OF ORGANOCLAY AND DOUBLE NETWORKING IN NATURAL RUBBER

2013 ◽  
Vol 86 (2) ◽  
pp. 205-217 ◽  
Author(s):  
Hedayatollah Sadeghi Ghari ◽  
Zahra Shakouri
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Natural Rubber ◽  
Physical And Mechanical Properties ◽  
X Ray Diffraction ◽  
Double Network ◽  
X Ray ◽  
Extension Ratio ◽  
Curing Characteristics ◽  
Scanning Electron

ABSTRACT Research was undertaken on natural rubber (NR) nanocomposites with organoclays. A double-network (DN) structure is formed when a partially cross-linked elastomer is further cross-linked during a state of strain. Two methods were used in the preparation of NR/organoclay nanocomposites: the ordinary method (single-network NR nanocomposite) and double-networked NR (DN-NR) nanocomposites. The single-networked NR nanocomposites were used for comparison. The effects of organoclay (5 phr) with a different extension ratio on curing characteristics, mechanical properties, hardness, swelling behavior, and morphology of single- and double-networked NR nanocomposites were studied. The results showed that double-networked NR nanocomposites exhibited higher physical and mechanical properties. The tensile strength of DN-NR nanocomposites increased up to 33 MPa (more than four times greater than that of pure NR) and then decreased with an increasing extension ratio. Modulus and hardness continuously increased with an increased extension ratio. The microstructure of the NR/organoclay systems was studied by X-ray diffraction and field emission scanning electron microscopy. The effects of different extension ratios on the dispersion of organoclay layers in the nanocomposites were investigated. Generally, results showed that the optimized extension ratio in DN nanocomposites was equal (or about or around) to α= 2.

Sign in / Sign up

Export Citation Format

Share Document