Wide Juncture Cracking Effect on the CRTS II Slab Track

2013 ◽  
Vol 405-408 ◽  
pp. 1824-1829 ◽  
Author(s):  
Si Fang Zhang ◽  
Juan Juan Ren ◽  
Ji Wang
Keyword(s):  
Mechanical Properties ◽  
Theoretical Analysis ◽  
Elastic Foundation ◽  
Solid Model ◽  
Slab Track ◽  
Service Environment ◽  
Temperature Load ◽  
Mechanics Analysis

The CRTSⅡ slab track is one of the major ballastless tracks in China. Factors of the design, the construction, the train load and the service environment lead to the wide juncture cracking. The beam-solid model on the elastic foundation was established to carry out the mechanics analysis. Theoretical analysis was made on the influence of the depth and the length of the cracking on mechanical properties of the CRTS Ⅱ slab track. The train load and temperature load can make the increase of the warping of the slab that cause the irregularity of the slab track. When the wide juncture crack completely, the sudden chill can make the slab track crack and effect the quality of ballastless tracks.

Pengaruh Tekanan dan Penggunaan Conplast terhadap Sifat Mekanik Eternit dari Abu Cangkang Sawit

2016 ◽  
Vol 8 (15) ◽  
pp. 47-54
Author(s):  
Haspiadi Haspiadi
Keyword(s):  
Mechanical Properties ◽  
Oil Palm ◽  
Modulus Of Elasticity ◽  
Modulus Of Rupture ◽  
Palm Shell ◽  
Oil Palm Shell ◽  
Density Values ◽  
Test Result

The purpose of this research is to know the influence of pressure and use of conplast against mechanical properties which are a Modulus of Elasticity (MOE) and Modulus of Rupture (MOR) of plasterboard. The study is done because still low quality of plasterboard made from a mixture of ashes of oil-palm shell especially of the mechanical properties compared to the controls. The method of this reserach used variation of printed pressure and the addition of conplast. Test result is obtained that the highest value of Modulus of Elasticity (MOE) 90875.94 Kg/cm2, Modulus of Rupture (MOR) 61.16 Kg/cm2 and density values in generally good printed at the pressure 60 g/cm3 and the addition of conplast 25% as well as the composition of the ash of palm shell oil 40%: limestone 40%: cement 15%: fiber 5% and 300 mL of water. ABSTRAK Tujuan dari penelitian ini adalah untuk mengetahui pengaruh tekanan dan penggunaan conplast terhadap sifat mekanik yaitu kuat lentur dan keteguhan patah eternit berbahan dasar abu cangkang sawit. Penelitian ini dilakukan karena masi rendahnya mutu eternit berbahan campuran abu cangkang sawit dari bolier khususnya sifat mekanik dibandingkan dengan kontrol. Metode penelitian yang digunakan adalah dengan variasi tekanan cetak dan penambahan conplast. Hasil uji diperoleh bahwa kuat lentur tertinggi sebesar 90875,94 Kg/cm2 dan keteguhan patah sebesar 61,16 Kg/cm2, yang dicetak pada tekanan 60 g/cm3 dan penambahan conplast 25% dengan komposisi  abu cangkang sawit 40 %: kapur 40 % : semen 15 %: serat 5 % dan air 300 mL.Kata Kunci :  Abu cangkang sawit, conplast, kuat lentur, keteguhan patah.

Interface damage and arching mechanism of CRTS II slab track under temperature load

2021 ◽  
Vol 291 ◽  
pp. 123258
Author(s):  
Xuhao Cui ◽  
Bowen Du ◽  
Hong Xiao ◽  
Rui Zhou ◽  
Gaoran Guo ◽  
...  
Keyword(s):  
Slab Track ◽  
Interface Damage ◽  
Temperature Load

scholarly journals Towards Recognition of Scale Effects in a Solid Model of Lattices with Tensegrity-Inspired Microstructure

Solids ◽  
2021 ◽  
Vol 2 (1) ◽  
pp. 50-59
Author(s):  
Wojciech Gilewski ◽  
Anna Al Sabouni-Zawadzka
Keyword(s):  
Mechanical Properties ◽  
Continuum Model ◽  
Scale Effects ◽  
Theory Of Elasticity ◽  
Solid Model ◽  
Gradient Theory ◽  
General Description ◽  
Normal Forces ◽  
Second Gradient ◽  
Proposed Model

This paper is dedicated to the extended solid (continuum) model of tensegrity structures or lattices. Tensegrity is defined as a pin-joined truss structure with an infinitesimal mechanism stabilized by a set of self-equilibrated normal forces. The proposed model is inspired by the continuum model that matches the first gradient theory of elasticity. The extension leads to the second- or higher-order gradient formulation. General description is supplemented with examples in 2D and 3D spaces. A detailed form of material coefficients related to the first and second deformation gradients is presented. Substitute mechanical properties of the lattice are dependent on the cable-to-strut stiffness ratio and self-stress. Scale effect as well as coupling of the first and second gradient terms are identified. The extended solid model can be used for the evaluation of unusual mechanical properties of tensegrity lattices.

scholarly journals Investigation of Color Reproduction on Linen Fabrics when Printing with Mimaki TX400-1800D Inkjet with Pigment TP250 Dyes

Coatings ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 354
Author(s):  
Tim Tofan ◽  
Rimantas Stonkus ◽  
Raimondas Jasevičius
Keyword(s):  
Mechanical Properties ◽  
Color Reproduction ◽  
Related Effect ◽  
Color Characteristics ◽  
Fabric Density ◽  
Different Types ◽  
The Difference ◽  
Printing Parameters ◽  
Linen Fabric

The aim of this research is to investigate related effect of dyeability to linen textiles related to different printing parameters. The study investigated the change in color characteristics when printing on linen fabrics with an inkjet MIMAKI Tx400-1800D printer with pigmented TP 250 inks. The dependence of color reproduction on linen fabrics on the number of print head passes, number of ink layers to be coated, linen fabric density, and different types of linen fabric was investigated. All this affects the quality of print and its mechanical properties. The change in color characteristics on different types of linen fabrics was determined experimentally. We determine at which print settings the most accurate color reproduction can be achieved on different linen fabrics. The difference between the highest and the lowest possible number of head passages was investigated. The possibilities of reproducing different linen fabric colors were determined.

scholarly journals The Influence of Different Plasma Cell Discharges on the Performance Quality of Surgical Gown Samples

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4329
Author(s):  
Atif H. Asghar ◽  
Ahmed Rida Galaly
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Exposure Time ◽  
Electrical Characteristics ◽  
Cathode Fall ◽  
Treatment Efficiency ◽  
Performance Quality ◽  
Surgical Gown ◽  
The One

An experimental study was performed on a low-density plasma discharge using two different configurations of the plasma cell cathode, namely, the one mesh system electrodes (OMSE) and the one mesh and three system electrodes (OMTSE), to determine the electrical characteristics of the plasma such as current–voltage characteristics, breakdown voltage (VB), Paschen curves, current density (J), cathode fall thickness (dc), and electron density of the treated sample. The influence of the electrical characteristics of the plasma fluid in the cathode fall region for different cathode configuration cells (OMSE and OMTSE) on the performance quality of a surgical gown was studied to determine surface modification, treatment efficiency, exposure time, wettability property, and mechanical properties. Over a very short exposure time, the treatment efficiency for the surgical gown surface of plasma over the mesh cathode at a distance equivalent to the cathode fall distance dc values of the OMTSE and for OMSE reached a maximum. The wettability property decreased from 90 to 40% for OMTSE over a 180 s exposure time and decreased from 90 to 10% for OMSE over a 160 s exposure time. The mechanisms of each stage of surgical gown treatment by plasma are described. In this study, the mechanical properties of the untreated and treated surgical gown samples such as the tensile strength and elongation percentage, ultimate tensile strength, yield strength, strain hardening, resilience, toughness, and fracture (breaking) point were studied. Plasma had a more positive effect on the mechanical properties of the OMSE reactor than those of the OMTSE reactor.

scholarly journals Effect of Ozone Treatment on the Quality of Sea Buckthorn (Hippophae rhamnoides L.)

Plants ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 847
Author(s):  
Anita Zapałowska ◽  
Natalia Matłok ◽  
Miłosz Zardzewiały ◽  
Tomasz Piechowiak ◽  
Maciej Balawejder
Keyword(s):  
Mechanical Properties ◽  
Volatile Compounds ◽  
Sea Buckthorn ◽  
Hippophae Rhamnoides ◽  
Ozone Treatment ◽  
Aerobic Bacteria ◽  
Hippophaë Rhamnoides ◽  
Hippophae Rhamnoïdes L ◽  
Ozonation Process

The aim of this research was to show the effect of the ozonation process on the quality of sea buckthorn (Hippophae rhamnoides L.). The quality of the ozonated berries of sea buckthorn was assessed. Prior to and after the ozone treatment, a number of parameters, including the mechanical properties, moisture content, microbial load, content of bioactive compounds, and composition of volatile compounds, were determined. The influence of the ozonation process on the composition of volatile compounds and mechanical properties was demonstrated. The ozonation had negligible impact on the weight and moisture of the samples immediately following the treatment. Significant differences in water content were recorded after 7 days of storage. It was shown that the highest dose of ozone (concentration and process time) amounting to 100 ppm for 30 min significantly reduced the water loss. The microbiological analyses showed the effect of ozone on the total count of aerobic bacteria, yeast, and mold. The applied process conditions resulted in the reduction of the number of aerobic bacteria colonies by 3 log cfu g−1 compared to the control (non-ozonated) sample, whereas the number of yeast and mold colonies decreased by 1 log cfu g−1 after the application of 100 ppm ozone gas for 30 min. As a consequence, ozone treatment enhanced the plant quality and extended plant’s storage life.

Influence of Agglomerate Size on the Properties of Al2O3-Al2Cu3 Multiphase Ceramic Coatings

2007 ◽  
Vol 336-338 ◽  
pp. 1791-1792
Author(s):  
Hai Ping Cui ◽  
Jun Yan ◽  
Shi Guo Du ◽  
Xin Kang Du
Keyword(s):  
Mechanical Properties ◽  
Size Range ◽  
Ceramic Coatings ◽  
Reactive System ◽  
Flame Spray ◽  
Agglomerate Size ◽  
Binding Strength

Al2O3-Al2Cu3 multiphase coatings were prepared on the surface of steel by reactive flame spray. The binding strength, microhardness and abrasion quality of the coatings were measured and analyzed. The influence of the agglomerate size on the properties of the coatings was emphatically studied to choose suitable size range for Al-CuO reactive system. The results showed that coatings prepared by using –150∼+250 meshes agglomerates exhibited good mechanical properties.

Application and Study of Reactive Polyacrylate Microgel in Pigment Paint of Printed Fabric

2011 ◽  
Vol 311-313 ◽  
pp. 1044-1048
Author(s):  
Hong Long Xing ◽  
Shui Lin Chen
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Transmission Electron Microscopy ◽  
Sodium Dodecyl ◽  
Ammonium Persulfate ◽  
Color Fastness ◽  
Adhesive Film ◽  
Transmission Electron ◽  
Divinyl Benzene

Polyacrylate microgel emulsion was prepared by emulsion polymerization using styrene, α-n-butyl acrylate and methyl methacrylate as monomer, polyoxyethylene octylphenol ether (TX-30) and sodium dodecyl sulfate(SDS) as combine emulsifier, divinyl benzene and ammonium persulfate (APS) as initiator，respectively. The prepared microgel was analyzed by a variety of measurment methods, such as Fourier transform infrared spectroscopy and transmission electron microscopy. The effect of microgel on the rheological properties of adhesives, leveling, mechanical properties and pigment printing performance was studied. The rhelogy and the color fastness of the pigment printing binder of printed fabrics were measured by rheometer and friction color fastness test instruments, respectively. At the same time, the mechanical properties of the adhesive film was measured by strength tester. The results show that the thixotropy, leveling and mechanical properties of adhesive printing binder and pringting quality of coating fabrics were improved when the microgel was added.

In Vitro and In Vivo Degradation, Mechanical Properties, and Histocompatibility of Weft-Knitted Silk Mesh-Like Grafts

2022 ◽  
Vol 12 (2) ◽  
pp. 411-416
Author(s):  
Liang Tang ◽  
Si-Yu Zhao ◽  
Ya-Dong Yang ◽  
Geng Yang ◽  
Wen-Yuan Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Simulated Body Fluid ◽  
Body Fluid ◽  
Degradation Rate ◽  
Maximum Load ◽  
Artificial Ligament ◽  
In Vivo Degradation

To investigate the degradation, mechanical properties, and histocompatibility of weft-knitted silk mesh-like grafts, we carried out the In Vitro and In Vivo silk grafts degradation assay. The In Vitro degradation experiment was performed by immersing the silk grafts in simulated body fluid for 1 year, and the results showed that the degradation rate of the silk mesh-like grafts was very slow, and there were few changes in the mechanical properties and quality of the silk mesh-like graft. In Vivo degradation assay was taken by implantation of the silk mesh-like grafts into the subcutaneous muscles of rabbits. At 3, 6, and 12 months postoperation, the rate of mass loss was 19.36%, 31.84%, and 58.77%, respectively, and the maximum load was 63.85%, 34.63%, and 10.76%, respectively of that prior to degradation. The results showed that the degradation rate of the silk graft and the loss of mechanical properties In Vivo were faster than the results obtained in the In Vitro experiments. In addition, there were no significant differences in secretion of serum IL-6 and TNF-α between the experimental and normal rabbits (P >0.05), suggesting no obvious inflammatory reaction. The findings suggest that the weft-knitted silk mesh-like grafts have good mechanical properties, histocompatibility, and In Vivo degradation rate, and therefore represent a candidate material for artificial ligament

Sign in / Sign up

Export Citation Format

Share Document