Warpage Characterization of Thin and Centrally-Gated Injection Molded Part by Applying Cavity Pressure Measurement

2013 ◽  
Vol 446-447 ◽  
pp. 1099-1103 ◽  
Author(s):  
H. Zamani ◽  
S. Azmoudeh ◽  
K. Shelesh-Nezhad
Keyword(s):  
Radial Flow ◽  
Mold Temperature ◽  
Cavity Pressure ◽  
Injection Speed ◽  
Molded Part ◽  
Pressure Time ◽  
Molded Parts ◽  
Injection Molded ◽  
Thin Disks

Two types of injection molded parts including parts with thin shell feature and parts molded with radial flow pattern are highly susceptible to the warpage. In this research, the warpage performance of a thin and centrally-gated disk was experimentally investigated. The melt pressure-time traces of two different locations inside the mold cavity were monitored by employing piezoelectric transducers. The results indicated that the pressure difference magnitude of melt at two locations along the radial flow path is related to the extent of molded part deformation. Moreover, it was pointed out that the high magnitude of warpage is because of two conflicting actions in the molded part comprising expansion as a result of viscoelastic recovery in the central region, and thermal contraction in the edge region of the thin disk. The molding variables encompassing injection speed, holding pressure, back pressure, mold temperature and screw rotational speed affected the thin disks deformation in order of significance.

Viscoelasticity Effects of Polymeric Material in Micro Injection Molding

2008 ◽  
Author(s):  
Peiman Mosaddegh ◽  
David C. Angstadt
Keyword(s):  
Oscillation Mode ◽  
Polymeric Materials ◽  
Elastic Response ◽  
Cavity Pressure ◽  
Molded Part ◽  
Molded Parts ◽  
Filling Phase ◽  
Injection Molded ◽  
Poly Ethylene ◽  
Peak Value

An experimental study has been carried out to determine the effect of viscoelasticity in comparison to viscosity on micro-injection molded parts. In this study, two different polymeric materials — Polystyrene (PS) as a viscous material and High Density Poly-Ethylene (HDPE) as a viscoelastic material — have been selected to observe the effect of melt elasticity on the filling phase of micro molding based on cavity pressure of molded part. All process parameters except temperature are the same for both polymers. Process temperatures have been selected in order to match the viscosity for both polymers used. Polymer viscosity was characterized at different shear rate and temperature. Viscoelasticity of both polymers were investigated using rotational rheometry in the oscillation mode. The mold geometry with high aspect ratio has been used and the effect of viscoelasticity on cavity pressure has been discussed. It was observed that there is retardation on the response of pressure because of elastic response of material during filling. Despite the differences in slope, peak value, area, and cycle time between two curves, they share similar trends. The only difference is their response during solidifying because of material property.

Study of the effect on conductivity and its uniform distribution in injection molded composite polymer bipolar plate

e-Polymers ◽  
2007 ◽  
Vol 7 (1) ◽  
Author(s):  
Chen Shia-Chung ◽  
Shih Ming-Yi ◽  
Lin Yi-Chang
Keyword(s):  
Flow Direction ◽  
Mold Temperature ◽  
Bipolar Plate ◽  
Surface Conductivity ◽  
Temperature Control System ◽  
Melt Flow ◽  
Molded Part ◽  
Molded Parts ◽  
Fluid Channel ◽  
Injection Molded

AbstractIn this study, PPS blended with as high as 50 wt% carbon fiber were injection molded. Effects of molding conditions as well as the melt flow condition parallel and perpendicular to fluid channel on the surface conductivity was investigated. It was found that mold temperature affects the surface conductivity of molded parts significantly. Using a variable mold temperature control system based on electromagnetic induction heating, the conductivity of the molded part increase by about 152% when the peak mold temperature increases from 120 °C to 210 °C. The channel layout also helps the fiber to orient more randomly leading to an increase in the conductivity. The channel design parallel to melt flow increases the conductivity by 152% and when it is perpendicular to melt flow, the conductivity increases by 95%. Channel layout perpendicular to melt flow direction provides more influence on the fiber reorientation than that of the parallel design.

Effect of Processing Conditions on the Shrinkage and Warpage of Glass Fiber Reinforced PP Using Microcellular Injection Molding

2012 ◽  
Vol 501 ◽  
pp. 294-299 ◽  
Author(s):  
Zhi Bian ◽  
Peng Cheng Xie ◽  
Yu Mei Ding ◽  
Wei Min Yang
Keyword(s):  
Injection Molding ◽  
Glass Fiber ◽  
Injection Pressure ◽  
Mold Temperature ◽  
Process Conditions ◽  
Fiber Reinforced ◽  
Injection Speed ◽  
Glass Fiber Reinforced ◽  
Microcellular Injection Molding ◽  
Molded Parts

This study was aimed at understanding how the process conditions affected the dimensional stability of glass fiber reinforced PP by microcellular injection molding. A design of experiments (DOE) was performed and plane test specimens were produced for the shrinkage and warpage analysis. Injection molding trials were performed by systematically adjusting six process parameters (i.e., Injection speed, Injection pressure, Shot temperature, SCF level, Mold temperature, and Cooling time). By analyzing the statistically significant main and two-factor interaction effects, the results showed that the supercritical fluid (SCF) level and the injection speed affected the shrinkage and warpage of microcellular injection molded parts the most.

scholarly journals Tie-Bar Elongation Based Filling-To-Packing Switchover Control and Prediction of Injection Molding Quality

Polymers ◽  
2019 ◽  
Vol 11 (7) ◽  
pp. 1168 ◽  
Author(s):  
Jian-Yu Chen ◽  
Chun-Ying Liu ◽  
Ming-Shyan Huang
Keyword(s):  
Injection Molding ◽  
Pressure Sensors ◽  
Clamping Force ◽  
Cavity Pressure ◽  
Testing Specimen ◽  
Injection Speed ◽  
Novel Approach ◽  
Pressure Profiles ◽  
Molded Parts ◽  
Short Shot

Filling-to-packing switchover (also called V/P switchover) is critical for assuring injection molding quality. An improper V/P switchover setting may result in various defects of injection-molded parts, such as excessive residual stress, flash, short shot, and warpage, etc. To enhance a consistent molding quality, recent V/P switchover approaches adopt cavity pressure profiles requiring sensors embedded in mold cavities, which is invasive to mold cavities and more expensive. Instead of using cavity pressure sensors, by working with the most popular screw position switchover control, this study hereby proposes a novel approach of tuning V/P switchover timing using a tie-bar elongation profile. In this investigation, a dumbbell testing specimen mold is applied to verify the feasibility of the method proposed. The results show that the mold filling and packing stages can be observed along the tie-bar elongation profile, detected by mounting strain gauges on the tie bars. Also, the characteristics of the cavity pressure are similar to those of the tie-bar elongation profile under a proper clamping force condition. Moreover, the varying process parameter settings which include injection speed, V/P switchover point, and holding pressure, can be reflected in these profiles. By extracting their characteristics, the application of the V/P switchover is proved to be realistic. This research conducted an experiment to verify the proposed V/P switchover decision method based on the tie-bar elongation profile. The result showed that the fluctuation of the part’s weight corresponding to a slight change of the barrel’s temperature from 210 °C to 215 °C can be successfully controlled with this method. Besides, the maximum clamping force increment extracted from the tie-bar elongation profile was found to be a good indicator for online monitoring of the reground material variation.

Effect of Size and Spatial Distribution of Titania Pigments in Injection Molded Parts on Surface Reflectance

2007 ◽  
Author(s):  
B. R. Dantal ◽  
A. Saigal ◽  
M. A. Zimmerman
Keyword(s):  
Spatial Distribution ◽  
Statistical Significance ◽  
Average Diameter ◽  
Area Fraction ◽  
Light Emitting ◽  
Molded Part ◽  
Molded Parts ◽  
Injection Molded ◽  
The Difference ◽  
New Applications

Titania pigments are used in molding compounds as a means to improve opacity by increasing the scattering efficiency of the medium and to develop new applications such as liquid crystal displays (LCD) and light emitting diodes (LED). The characteristics of the injection molded products are a function of molding parameters such as gate location and shear rate. In this study, quantitative measures of the particle distribution of titania pigments in polymer composites have been experimentally determined, including area fraction, average diameter, and diameter volume. A 2 × 3 × 3 ANOVA test has been conducted to assess the statistical significance of these parameters. This study deals with the size and spatial distribution of the particles. The important parameters calculated based on the Feret’s diameter are diameter-volume (dv), diameter-number (dn), and area fraction (AF). The term diameter-volume (dv) has been used to give greater significance to the large particles and thus ‘large’ indicates more and/or larger particles. The parameters have been calculated by using Image-J image processing software. MINITAB has been used to assess the statistical significance of these parameters. The results show that titania particles are not uniformly distributed within the final molded parts and they vary along the molding (longitudinal) and transverse directions of plastic flow. The difference of pigment area fraction and diameter volume at different locations within a final molded part has a significant effect on the percentage reflectance of the surface.

Filling-to-Packing Switchover Mode Based on Cavity Pressure for Injection Molding

2012 ◽  
Vol 501 ◽  
pp. 168-173 ◽  
Author(s):  
Jian Wang
Keyword(s):  
Injection Molding ◽  
Crucial Role ◽  
Mold Temperature ◽  
The Other ◽  
Injection Time ◽  
Cavity Pressure ◽  
Part Quality ◽  
Molded Parts ◽  
Screw Position

Filling-to-packing switchover control during injection molding plays a crucial role in ensuring the quality of the molded parts. In this study, a filling-to-packing switchover mode based on cavity pressure was presented, and it was compared with other two switchover modes by injection time and screw position. The objective of this study was to validate the accuracy of the switchover mode based on cavity pressure, and examine its consistency. Weight of the molded parts served as the main measure to probe the process capabilities. In this study, the change in mold temperature was monitored; variation of mold temperature affecting the process was examined. The results of the verification experiments revealed that the switchover mode based on cavity pressure could yield a better part quality and consistent part weight compared with the other two traditional switchover modes. It was proved that the switchover mode by cavity pressure can be used to improve the precision of the injection molding. However, a suitable switchover pressure must be used for achieving such high process capability, and the position to get the pressure signal and mold temperature should also be considered.

Sign in / Sign up

Export Citation Format

Share Document