Rotor Design and Performance Study of a Vertical-Axis Wind Turbine Based on DMS

2013 ◽  
Vol 448-453 ◽  
pp. 1892-1896
Author(s):  
Rui Yang ◽  
Jin Long Li ◽  
Wei Wei Xia ◽  
Ting Ting Wang
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Aerodynamic Load ◽  
Vertical Axis Wind Turbine ◽  
Performance Study ◽  
Force Coefficient ◽  
Rotor Design ◽  
And Performance

Specifically address the design of a 5KW H-type vertical-axis wind turbine (H-VAWT) with NACA 0018 airfoil considering the factors that affect wind turbine power. The double-multiple streamtube (DMS) theoretical model is analyzed and summarized and calculated by Matlab. The 5KW H-type vertical axis wind turbines aerodynamic performance is calculated by the model written in Matlab. The curve of the power coefficient as a function of the tip-speed ratio and the curve of the normal force coefficient and the tangential farce as a function of the blade position is given by Matlab. From the curves we can see that upwind rotor aerodynamic load is larger, downwind rotor aerodynamic load is smaller and there is a serious flow retarding effect in the rotor downwind area.

Numerical Research on the Characteristics of Lift-Drag Type Vertical Axis Wind Turbine

2012 ◽  
Vol 189 ◽  
pp. 448-452
Author(s):  
Yan Jun Chen ◽  
Guo Qing Wu ◽  
Yang Cao ◽  
Dian Gui Huang ◽  
Qin Wang ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Chord Length ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Middle Range ◽  
Parabolic Form ◽  
Cfd Method

Numerical studies are conducted to research the performance of a kind of lift-drag type vertical axis wind turbine (VAWT) affected by solidity with the CFD method. Moving mesh technique is used to construct the model. The Spalart-Allmaras one equation turbulent model and the implicit coupled algorithm based on pressure are selected to solve the transient equations. In this research, how the tip speed ratio and the solidity of blade affect the power coefficient (Cp) of the small H-VAWT is analyzed. The results indicate that Cp curves exhibit approximate parabolic form with its maximum in the middle range of tip speed ratio. The two-blade wind turbine has the lowest Cp while the three-blade one is more powerful and the four-blade one brings the highest power. With the certain number of blades, there is a best chord length, and too long or too short chord length may reduce the Cp.

Experimental Study of Vertical Axis Wind Turbine with Wind Speed Self-Adapting

2012 ◽  
Vol 215-216 ◽  
pp. 1323-1326
Author(s):  
Ming Wei Xu ◽  
Jian Jun Qu ◽  
Han Zhang
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Wind Velocity ◽  
Vertical Axis ◽  
Maximum Power ◽  
The Self ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Opening And Closing

A small vertical axis wind turbine with wind speed self-adapting was designed. The diameter and height of the turbine were both 0.7m. It featured that the blades were composed of movable and fixed blades, and the opening and closing of the movable blades realized the wind speed self-adapting. Aerodynamic performance of this new kind turbine was tested in a simple wind tunnel. Then the self-starting and power coefficient of the turbine were studied. The turbine with load could reliably self-start and operate stably even when the wind velocity was only 3.6 m/s. When the wind velocity was 8 m/s and the load torque was 0.1Nm, the movable blades no longer opened and the wind turbine realized the conversion from drag mode to lift mode. With the increase of wind speed, the maximum power coefficient of the turbine also improves gradually. Under 8 m/s wind speed, the maximum power coefficient of the turbine reaches to 12.26%. The experimental results showed that the new turbine not only improved the self-starting ability of the lift-style turbine, but also had a higher power coefficient in low tip speed ratio.

scholarly journals A Dynamic Rotor Vertical-Axis Wind Turbine with a Blade Transitioning Capability

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1446 ◽  
Author(s):  
Elie Antar ◽  
Amne El Cheikh ◽  
Michel Elkhoury
Keyword(s):  
Wind Turbine ◽  
Average Power ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Optimized Design ◽  
Detached Eddy Simulation ◽  
Vertical Axis Wind Turbine ◽  
Eddy Simulation ◽  
Delayed Detached Eddy Simulation

This work presents an optimized design of a dynamic rotor vertical-axis wind turbine (DR VAWT) which maximizes the operational tip-speed ratio (TSR) range and the average power coefficient (Cp) value while maintaining a low cut-in wind velocity. The DR VAWT is capable of mimicking a Savonius rotor during the start-up phase and transitioning into a Darrieus one with increasing rotor radius at higher TSRs. The design exploits the fact that with increasing rotor radius, the TSR value increases, where the peak power coefficient is attained. A 2.5D improved delayed detached eddy simulation (IDDES) approach was adopted in order to optimize the dynamic rotor design, where results showed that the generated blades’ trajectories can be readily replicated by simple mechanisms in reality. A thorough sensitivity analysis was conducted on the generated optimized blades’ trajectories, where results showed that they were insensitive to values of the Reynolds number. The performance of the DR VAWT turbine with its blades following different trajectories was contrasted with the optimized turbine, where the influence of the blade pitch angle was highlighted. Moreover, a cross comparison between the performance of the proposed design and that of the hybrid Savonius–Darrieus one found in the literature was carefully made. Finally, the effect of airfoil thickness on the performance of the optimized DR VAWT was thoroughly analyzed.

Vortex Sheet Analysis of the Giromill

1978 ◽  
Vol 100 (3) ◽  
pp. 340-342 ◽  
Author(s):  
R. E. Wilson
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Vortex Sheet ◽  
Maximum Energy ◽  
Power Coefficient ◽  
Two Dimensional ◽  
Vertical Axis Wind Turbine ◽  
Wind Force ◽  
Force Coefficient ◽  
Horizontal Axis Wind Turbine

A two-dimensional analysis of the performance and flowfield of the Giromill is presented. The Giromill is a vertical-axis wind turbine with straight blades that are articulated to produce maximum energy extraction from the wind. It is found that the power coefficient and windwise force coefficient for the Giromill have the same limit as obtained for the horizontal-axis wind turbine. A cross-wind force is also obtained with this type of wind turbine. The cross-wind force is of second order and decreases with tip speed. Streamlines and velocity profiles are illustrated for several loading conditions.

An Experimental Study of the Aerodynamics and Performance of a Vertical Axis Wind Turbine in a Confined and Unconfined Environment

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Vincenzo Dossena ◽  
Giacomo Persico ◽  
Berardo Paradiso ◽  
Lorenzo Battisti ◽  
Sergio Dell'Anna ◽  
...  
Keyword(s):  
Experimental Study ◽  
Wind Tunnel ◽  
Wind Turbine ◽  
Vertical Axis ◽  
Tip Vortex ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
And Performance ◽  
Power Curves

This paper presents the results of a wide experimental study on an H-type vertical axis wind turbine (VAWT) carried out at the Politecnico di Milano. The experiments were carried out in a large-scale wind tunnel, where wind turbines for microgeneration can be tested in real-scale conditions. Integral torque and thrust measurements were performed, as well as detailed aerodynamic measurements to characterize the flow field generated by the turbine downstream of the rotor. The machine was tested in both a confined (closed chamber) and unconfined (open chamber) environment, to highlight the effect of wind tunnel blockage on the aerodynamics and performance of the VAWT under investigation. The experimental results, compared with the blockage correlations presently available, suggest that specific correction models should be developed for VAWTs. The experimental thrust and power curves of the turbine, derived from integral measurements, exhibit the expected trends with a peak power coefficient of about 0.28 at tip-speed ratio equal to 2.5. Flow measurements, performed in three conditions for tip speed ratio equal to 1.5, 2.5, and 3.5, show the fully three-dimensional character of the wake, especially in the tip region where a nonsymmetrical wake and tip vortex are found. The unsteady evolution of the velocity and turbulence fields further highlights the effect of aerodynamic loading on the wake unsteadiness, showing the time-dependent nature of the tip vortex and the onset of dynamic stall for tip speed ratio lower than 2.

scholarly journals PENGARUH JUMLAH BLADE DAN VARIASI PANJANG CHORD TERHADAP PERFORMANSI TURBIN ANGIN SUMBU HORIZONTAL (TASH)

2014 ◽  
Vol 4 (2) ◽  
Author(s):  
I Kade Wiratama ◽  
Made Mara ◽  
L. Edsona Furqan Prina
Keyword(s):  
Wind Turbine ◽  
Energy Use ◽  
Electrical Energy ◽  
Vertical Axis ◽  
Energy System ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine

The willingness of electrical energy is one energy system has a very important role in the economic development of a country's survival. As one energy source (wind) can be converted into electrical energy with the use of a horizontal axis wind turbine. Wind Energy Conversion Systems (WECS) that we know are two wind turbines in general, ie the horizontal axis wind turbine and vertical axis wind turbine is one type of renewable energy use wind as an energy generator. The purpose of this study was to determine the effect of the number of blade and the radius chord of rotation (n), Torque (T), Turbine Power (P), Power Coefficient (CP) and Tip Speed Ratio (λ) generated by the horizontal axis wind turbine with form linear taper. The results show that by at the maximum radius of the chord R3 the number blade 4 is at rotation = 302.700 rpm, Pturbine = 7.765 watt, Torque = 0.245 Nm, λ = 3.168 and Cp = 0.403 or 40.3%.

Performance Improvements for a Vertical Axis Wind Turbine by Means of Gurney Flap

2019 ◽  
Vol 142 (2) ◽  
Author(s):  
Yan Yan ◽  
Eldad Avital ◽  
John Williams ◽  
Jiahuan Cui
Keyword(s):  
Wind Turbine ◽  
Stokes Equations ◽  
Numerical Study ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Navier Stokes ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Performance Improvements ◽  
Gurney Flap

Abstract A numerical study was carried out to investigate the effects of a Gurney flap (GF) on the aerodynamics performance of the NACA 00 aerofoil and an associated three-blade rotor of a H-type Darrieus wind turbine. The flow fields around a single aerofoil and the vertical axis wind turbine (VAWT) rotor are studied using unsteady Reynolds-averaged Navier–Stokes equations (URANS). The height of GF ranges from 1% to 5% of the aerofoil chord length. The results show that the GF can increase the lift and lift-to-drag ratio of the aerofoil as associated with the generation of additional vortices near the aerofoil trailing edge. As a result, adding a GF can significantly improve the power coefficient of the VAWT at low tip speed ratio (TSR), where it typically gives low power production. The causing mechanism is discussed in detail, pointing to flow separation and dynamic stall delay.

scholarly journals Studi simulasi penggunaan airfoil naca 6412 sebagai sudu pada turbin angin crossflow melalui pemodelan CFD 2 dimensi

2018 ◽  
Vol 13 (1) ◽  
pp. 28
Author(s):  
Muhammad Ivan Fadhil Hendrawan ◽  
Dominicus Danardono ◽  
Syamsul Hadi
Keyword(s):  
Wind Turbine ◽  
Constant Velocity ◽  
Cross Flow ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Ansys Fluent ◽  
Tip Speed Ratio ◽  
Blade Number

AbstractThe simulation aimed to understand the effect of the angle of blade number and blade number of vertical axis wind turbine with cross flow runner to enhance the performance of wind turbine. The turbine had 20, 22, and 24 number of blades. Simulation was done in 2D analysis using ANSYS-Fluent. Tip speed ratio was varied in range of 0,1-0,5 with constant velocity inlet 2 m/s. The effect of blade numbers to torque and power coefficient were analyzed and compared. It had been found that the best power coefficient were 0,5 at tip speed ratio 0,3.

Numerical Investigation of Modified Bach Type Vertical Axis Wind Turbine

2016 ◽  
Vol 852 ◽  
pp. 551-557 ◽  
Author(s):  
R. Sarath Kumar ◽  
T. Micha Premkumar ◽  
Sivamani Seralathan ◽  
T. Mohan
Keyword(s):  
Wind Turbine ◽  
Vertical Axis ◽  
Flow Behaviour ◽  
Power Coefficient ◽  
Navier Stokes ◽  
Vertical Axis Wind Turbine ◽  
Navier Stokes Equation ◽  
Ansys Fluent ◽  
Improved Performance ◽  
And Performance

This study evaluates the performance and flow behaviour over the modified Bach type Vertical Axis Wind Turbine. A two dimensional unsteady state analysis is carried out in this study. The unsteady Reynolds Averaged Navier-Stokes equation and the turbulence equation corresponding to SST k-ω turbulence model are solved using commercial software ANSYS FLUENT 13. A grid independence study is performed to choose optimum mesh elements. The simulation is carried out and performance parameters like power coefficient and torque coefficient are calculated. The results are compared with the available experimental data for validation purpose and these matched with numerical values. An improved performance of around 37% Cp is observed for modified Bach type over simple Savonius rotor. Moreover, a brief analysis of flow behaviour over the rotor is studied.

scholarly journals Studi Eksperimen Pengaruh Jumlah Sudu Terhadap Kinerja Wind Turbine Crossflow

2021 ◽  
Vol 16 (2) ◽  
pp. 218
Author(s):  
Fahrudin Fahrudin ◽  
Fitri Wahyuni ◽  
Dini Oktavitasari
Keyword(s):  
Wind Turbine ◽  
Alternative Energy ◽  
Wind Tunnel Test ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Speed Ratio ◽  
Test Scheme ◽  
Vertical Axis Wind Turbine ◽  
Tip Speed Ratio ◽  
Torque Coefficient

<p>Wind is an alternative energy that is environmentally friendly and sustainable. Therefore, we need a type of wind turbine that can receive wind from all directions. The crossflow type vertical axis wind turbine has a high torque coefficient at a low tip speed ratio. The purpose of this study was to determine the effect of the number of blades on the performance of the vertical axis crossflow wind turbine. The experimental test was carried out by varying the number of blades. The configuration is analyzed using the experimental wind tunnel test scheme which has been modified in the section test section. The results showed that the number of blades 16 has a power coefficient ( ) = 0.23 tip speed ratio (TSR) = 0.42 at a wind speed of 4 m / s.</p><p><strong><br /></strong></p>

Sign in / Sign up

Export Citation Format

Share Document