Theoretical Analysis and Experimental Study on the Vibration of the Bimorph Piezoelectric Vibrator for Piezoelectric Pump

2014 ◽  
Vol 551 ◽  
pp. 164-169 ◽  
Author(s):  
Wei Zheng ◽  
Bai Song Lin ◽  
Jing Shi Dong ◽  
Jing Yuan Shi ◽  
Bo Da Wu
Keyword(s):  
Finite Element ◽  
Finite Element Simulation ◽  
Vibration Mode ◽  
Test Results ◽  
Piezoelectric Pump ◽  
Bending Vibration ◽  
Piezoelectric Vibrator ◽  
Element Simulation ◽  
Support Conditions ◽  
The Relationship

This paper studied the characteristics of the bimorph piezoelectric vibrator for piezoelectric pump. By simulating the working conditions of the vibration in the pump, we constructed a dynamic model and derived the bending vibration equations of the piezoelectric vibrator under different support conditions. Then the analysis of finite element simulation is carried out for the equations, through which the vibration mode of the multi-order modal of the piezoelectric vibrator was acquired, and the relationship between the deformation deflection and peripheral support stiffness of the piezoelectric vibrator was analyzed. Finally, the deformation of the piezoelectric vibrator was tested. It is found that the test results are consistent with the conclusions of the finite element simulation, which provides a theoretical basis for the optimal design of the bimorph piezoelectric vibrator.

Simulation of hot high-speed yielding of intermetallic titanium alloy VTI-4 under conditions of high-speed loading

2020 ◽  
Vol 0 (12) ◽  
pp. 10-16
Author(s):  
V.V. Avtaev ◽  
◽  
D. V. Grinevich ◽  
A. V. Zavodov
Keyword(s):  
Finite Element ◽  
Titanium Alloy ◽  
Strain Rate ◽  
Finite Element Simulation ◽  
Modulus Of Elasticity ◽  
High Speed ◽  
Residual Deformation ◽  
Test Results ◽  
Element Simulation ◽  
The Relationship

Yielding tests of VTI-4 alloy specimens have been carried out at temperature 1010 °C under conditions of high-speed loading. Based on the test results the modulus of elasticity as well as axial and radial residual deformation values in the end and central zones for each loading stage were determined. Fitting criteria for finite element simulation and the experiment are proposed with tracing VTI-4 alloy diagram deformation at temperature 1010 °C and strain rate of 2.5 sec–1. As a result of finite element simulation the relationship between the material structures obtained during high-speed yielding and the deflected modes in different zones was determined.

scholarly journals Theoretical analysis and experimental research on multi-layer elastic damping track structure

2021 ◽  
Vol 13 (2) ◽  
pp. 168781402199497
Author(s):  
Guanghui Xu ◽  
Shengkai Su ◽  
Anbin Wang ◽  
Ruolin Hu
Keyword(s):  
Finite Element ◽  
Analytical Solution ◽  
Finite Element Simulation ◽  
Reaction Force ◽  
Vibration Reduction ◽  
Vertical Direction ◽  
Propagation Path ◽  
Track Structure ◽  
Test Results ◽  
Element Simulation

The increase of axle load and train speed would cause intense wheelrail interactions, and lead to potential vibration related problems in train operation. For the low-frequency vibration reduction of a track system, a multi-layer track structure was proposed and analyzed theoretically and experimentally. Firstly, the analytical solution was derived theoretically, and followed by a parametric analysis to verify the vibration reduction performance. Then, a finite element simulation is carried out to highlight the influence of the tuned slab damper. Finally, the vibration and noise tests are performed to verify the results of the analytical solution and finite element simulation. As the finite element simulation indicates, after installation of the tuned slab damper, the peak reaction force of the foundation can be reduced by 60%, and the peak value of the vertical vibration acceleration would decrease by 50%. The vibration test results show that the insertion losses for the total vibration levels are 13.3 dB in the vertical direction and 21.7 dB in the transverse direction. The noise test results show that the data of each measurement point is smoother and smaller, and the noise in the generating position and propagation path can be reduced by 1.9 dB–5.5 dB.

scholarly journals Effect of the Supports’ Positions on the Vibration Characteristics of a Flexible Rotor Shafting

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Miaomiao Li ◽  
Zhuo Li ◽  
Liangliang Ma ◽  
Rupeng Zhu ◽  
Xizhi Ma
Keyword(s):  
Finite Element ◽  
Finite Element Simulation ◽  
Vibration Characteristics ◽  
Rotor System ◽  
Experimental Investigations ◽  
Flexible Rotor ◽  
Bending Vibration ◽  
First Order ◽  
Element Simulation

In this study, we evaluated the effect of changing supports’ position on the vibration characteristics of a three-support flexible rotor shafting. This dependency was first analyzed using a finite element simulation and then backed up with experimental investigations. By computing a simplified rotor shafting model, we found that the first-order bending vibration in a forward whirl mode is the most relevant deforming mode. Hence, the effect of the supports’ positions on this vibration was intensively investigated using simulations and verified experimentally with a house-made shafting rotor system. The results demonstrated that the interaction between different supports can influence the overall vibration deformation and that the position of the support closer to the rotor has the greatest influence.

Finite Element Simulation and Comparison of Hydraulic Splitting Fracturing Test of Concrete

2014 ◽  
Vol 678 ◽  
pp. 551-555
Author(s):  
Xue Zhi Wang ◽  
Hao Fei Zou ◽  
Shu Wen Zheng ◽  
Yuan Li ◽  
Jun Yu Liu
Keyword(s):  
Finite Element ◽  
Finite Element Simulation ◽  
Mixed Mode ◽  
Failure Process ◽  
Crack Tip ◽  
Mixed Mode Fracture ◽  
Test Results ◽  
Mode Fracture ◽  
Element Simulation ◽  
Simulation Results

I-II mixed mode fracture under two kinds of load manners was carried out, and it was also simulated by the ANSYS, and the test results and the simulation results were compared and analyzed, and the reasonableness of the model built and the effectiveness of test were verified. The failure process of fracture under the loading could be judged through the development of the crack tip combined with the stress nephogram and strain nephogram when cracks initiation at crack tip, and it provided the basis for the crack damage judgment.

Mechanism Research on Pelleting Process and Block Self-Healing of Mixture Recycled Plastics in Die-Plate

2015 ◽  
Vol 768 ◽  
pp. 36-44
Author(s):  
Yong Gang Zou ◽  
Bo Wang ◽  
Xiao Feng Liu ◽  
Bing Zhang
Keyword(s):  
Finite Element ◽  
Rheological Properties ◽  
Finite Element Simulation ◽  
Polymer Melt ◽  
Self Healing ◽  
Melting Points ◽  
Element Simulation ◽  
Mechanism Research ◽  
Recycled Plastics ◽  
The Relationship

For many recycled plastics, materials with different rheological properties and melting points are usually mixed together, and can not be separated. For this situation, the block of die-plate holes can be regarded as an important factor that must be taken into consideration in pelleting process. This paper discusses pelleting process in die-plate and reasons of die hole’s blocking. Finite element simulation is calculated to analyze the relationship between operation factors of pelleting process and blocking situation of die holes. Furthermore, block self-healing is realized by changing the velocity of polymer-melt in die-hole.

Influence of feed per tooth on tool wear based on 3D finite element simulation in micro-milling of Inconel 718

2017 ◽  
Vol 69 (4) ◽  
pp. 585-590 ◽  
Author(s):  
Xiaohong Lu ◽  
FuRui Wang ◽  
Zhenyuan Jia ◽  
Likun Si ◽  
Yongqiang Weng
Keyword(s):  
Finite Element ◽  
Tool Wear ◽  
Finite Element Simulation ◽  
Inconel 718 ◽  
Chip Thickness ◽  
Micro Milling ◽  
Wear Depth ◽  
Content Type ◽  
Element Simulation ◽  
The Relationship

Purpose This paper aims to predict tool wear and reveal the relationship between feed per tooth and tool wear in micro-milling Inconel 718 process. Design/methodology/approach To study and solve the tool wear problem in micro-milling of Inconel 718 micro components, in this paper, the investigation of micro-milling Inconel 718 process was implemented based on DEFORM finite element simulation, and tool wear depth of micro-milling cutter acted as output. Findings Different from the traditional macro milling process, diameter reduction percentage and average flank wear length decreased with the increase of feed per tooth; tool wear depth decreased when the feed per tooth was less than the minimum chip thickness. Originality/value At present, research on the prediction of tool wear in micro-milling of Inconel 718 has never been publicly reported. This study is significant to reveal the relationship between cutting parameters (feed per tooth) and tool wear in micro-milling Inconel 718.

Design, Simulation and Fabrication of an Air-Driven Microturbomachine

2011 ◽  
Vol 483 ◽  
pp. 611-615
Author(s):  
Shao Chun Sun ◽  
Geng Chen Shi
Keyword(s):  
Finite Element ◽  
Finite Element Simulation ◽  
Working Condition ◽  
Rotation Speed ◽  
Power Source ◽  
Flow Speed ◽  
Test Results ◽  
Element Simulation ◽  
Power Turbine ◽  
Driving Torque

This paper presents the design, simulation and fabrication of an mm-scale air-driven microturbomachine. The circumferential-flow turbomachine has a plain-shaped structure with an overall size of 8×8×3mm3. The predicted formulas for driving torque and driving power are deduced by analyzing the working condition of the model. Finite element simulation is carried out to determine the driving torque and driving power. Turbine and stator are fabricated using UV-LIGA technique, while other components using pension micromachining. Test results of assembled prototype show that under the air-flow speed of 80m/s, no-load and load rotation speed are 10kr/min and 9.5kr/min respectively, and the output power is 326.57µW. The results indicate micro turbomachine is potential power source for the micro system.

Sign in / Sign up

Export Citation Format

Share Document