In-Plane Behavior of BFRP Sheets Bonded to Damaged RC-Brick Masonry Walls with Opening

2014 ◽  
Vol 684 ◽  
pp. 195-201
Author(s):  
Zhen Lei ◽  
Yong Wang ◽  
Jun Tong Qu
Keyword(s):  
Energy Dissipation ◽  
Masonry Wall ◽  
Shear Loading ◽  
Brick Masonry ◽  
Masonry Walls ◽  
Deformation Capacity ◽  
Plane Shear ◽  
Lateral Strength ◽  
Strength And Deformation ◽  
Energy Dissipation Capacity

FRP strength technique can increase the lateral strength of masonry walls, but the effect of the presence of pre-damage in the walls before retrofitted has not been studied. In this study, the experimental results from two half-scale RC-brick masonry walls with opening retrofitted with BFRP composite strips are presented. One wall was initially damaged in shear loading up to its maximum strength, and then repaired with BFRP sheets; another one was directly strengthened with BFRP sheets in the same strengthening configuration. All the walls were subjected to cyclic in-plane shear loading up to failure. Compared to the strengthened walls, the repaired masonry wall has almost the same failure mode and FRP strain rule, and slightly lower lateral strength and deformation capacity as well as energy dissipation capacity.

scholarly journals Experimental Analysis of Seismic Performance of Masonry Shear Wall Reinforced with PP-Band Mesh and Plastering Mortar under In-Plane Cyclic Loading

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Qiang Zhou ◽  
Lingyu Yang ◽  
Wenyang Zhao
Keyword(s):  
Energy Dissipation ◽  
Cyclic Loading ◽  
Bearing Capacity ◽  
Low Cost ◽  
Low Frequency ◽  
Masonry Wall ◽  
Ultimate Bearing Capacity ◽  
Masonry Walls ◽  
Seismic Capacity ◽  
Energy Dissipation Capacity

Masonry structures are widely used in developing countries due to their low cost and simple construction, especially in remote areas, where there are a large number of houses without seismic measures. These buildings are prone to collapse and cause a lot of casualties, even under the action of small earthquakes. For the reinforcement of this structure, a cheap, effective, and easy-to-construct reinforcement method is urgently needed. Therefore, this article studies the reinforcement method of polypropylene bands (PP-bands). We have carried out low-frequency cyclic loading tests for two PP-band reinforced masonry walls and two compared masonry walls. We mainly studied the influence of PP-band and different compressive strengths of plastering mortar on the masonry wall’s seismic capacity. The seismic indicators mainly studied in this article include ultimate bearing capacity, energy dissipation capacity, stiffness degradation, and hysteresis characteristics. The experimental results show that the PP-band can greatly enhance the seismic capacity of the masonry wall. The ultimate bearing capacity, energy dissipation capacity, and displacement ductility of the PP-band reinforced wall are increased by 38%–48%, 22%–47%, and 138%–226%.

scholarly journals Experimental Research on Seismic Performance of Damaged Brick Walls Strengthened with Embedded Horizontal Steel Bars

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Liu Tingbin ◽  
Jia Rubo ◽  
Pei Xianke ◽  
Zhang Jiawei ◽  
Zhao Jianchang
Keyword(s):  
Energy Dissipation ◽  
Seismic Performance ◽  
Masonry Wall ◽  
Shear Capacity ◽  
Brick Masonry ◽  
Reconstruction Process ◽  
Skeleton Curve ◽  
Aspect Ratios ◽  
Steel Bars ◽  
Energy Dissipation Capacity

Six brick masonry specimens (two unreinforced specimens, two reinforced specimens, and two specimens reinforced after being damaged), which have different aspect ratios, were tested under low-frequency cyclic loading. The seismic performances of these specimens, including failure characteristics, deformation capacity, carrying capacity, energy dissipation capacity, hysteresis characteristics, and stiffness degradation, were analyzed. The following results were obtained: the ductility of the damaged walls could be significantly improved after they were reinforced with embedded horizontal steel bars; the ultimate shear capacity of the damaged brick masonry walls with the aspect ratios of 1.8 and 0.5 was improved by 6.8% and 4.7%, respectively; the displacement corresponding to the ultimate bearing capacity was close to that of the unreinforced brick masonry wall; the hysteresis loop of the reinforced wall became plumper and encompassed a larger area; after the ultimate load was reached, a clear yielding platform appeared in the skeleton curve of the reinforced wall; the reinforced wall exhibited good ductility, after entering plastic stage; the energy dissipation capacity of the reinforced wall was significantly greater than that of the unreinforced wall. In conclusion, the seismic performance of the damaged brick masonry wall can be improved by embedding horizontal steel bars, and this reinforcing method can be applied in the postseismic reconstruction process.

scholarly journals Numerical Modeling of Unreinforced Masonry Walls Strengthened with Fe-Based Shape Memory Alloy Strips

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2961
Author(s):  
Moein Rezapour ◽  
Mehdi Ghassemieh ◽  
Masoud Motavalli ◽  
Moslem Shahverdi
Keyword(s):  
Energy Dissipation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Unreinforced Masonry ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Vertical Strip ◽  
Maximum Resistance ◽  
The Cross ◽  
Post Tensioning

This study presents a new way to improve masonry wall behavior. Masonry structures comprise a significant part of the world’s structures. These structures are very vulnerable to earthquakes, and their performances need to be improved. One way to enhance the performances of such types of structures is the use of post-tensioning reinforcements. In the current study, the effects of shape memory alloy as post-tensioning reinforcements on originally unreinforced masonry walls were investigated using finite element simulations in Abaqus. The developed models were validated based on experimental results in the literature. Iron-based shape memory alloy strips were installed on masonry walls by three different configurations, namely in cross or vertical forms. Seven macroscopic masonry walls were modeled in Abaqus software and were subjected to cyclic loading protocol. Parameters such as stiffness, strength, durability, and energy dissipation of these models were then compared. According to the results, the Fe-based strips increased the strength, stiffness, and energy dissipation capacity. So that in the vertical-strip walls, the stiffness increases by 98.1%, and in the cross-strip model's position, the stiffness increases by 127.9%. In the vertical-strip model, the maximum resistance is equal to 108 kN, while in the end cycle, this number is reduced by almost half and reaches 40 kN, in the cross-strip model, the maximum resistance is equal to 104 kN, and in the final cycle, this number decreases by only 13.5% and reaches 90 kN. The scattering of Fe-based strips plays an important role in energy dissipation. Based on the observed behaviors, the greater the scattering, the higher the energy dissipation. The increase was more visible in the walls with the configuration of the crossed Fe-based strips.

Influence of Sulphate on the Moisture Movement of Calcium Silicate Brick Masonry Wall

2010 ◽  
Vol 133-134 ◽  
pp. 201-204
Author(s):  
Ibrahim Mohamad H. Wan ◽  
B.H. Abu Bakar ◽  
M.A. Megat Johari ◽  
P.J. Ramadhansyah
Keyword(s):  
Relative Humidity ◽  
Calcium Silicate ◽  
Masonry Wall ◽  
Sodium Sulphate ◽  
Brick Masonry ◽  
Masonry Walls ◽  
Moisture Movement ◽  
Moisture Expansion ◽  
Curing Period ◽  
Wet Condition

This paper presents the behaviour of moisture movement of calcium silicate brick masonry walls exposed to sodium sulphate environment. The walls were exposed to three sodium sulphate conditions with sulphate concentrations of5%, 10% and 15%. For comparison, some walls were also exposed to dry and wet condition which acts as a control conditions. All specimens were prepared and cured under polythene sheet for 14 days in a controlled environmental room and maintained at relative humidity and temperature of 80 ± 5% and 25 ± 2°C, respectively. After the curing period, the specimens were exposed to sodium sulphate as well as drying and water exposures, during which moisture movement was measured and monitored for a period of up to 7 months. As a result, the moisture expansion was observed and recorded for all masonry wall specimens after exposed to the sulphate condition.

Effect of Detailed Formations on the In-Plane Shear Capacity of Hairpin Connectors in Precast RC Floor Slabs

2010 ◽  
Vol 163-167 ◽  
pp. 1510-1514 ◽  
Author(s):  
Rui Pang ◽  
Shu Ting Liang ◽  
Xiao Jun Zhu ◽  
Yao Meng
Keyword(s):  
Simulation Analysis ◽  
Plate Thickness ◽  
Shear Capacity ◽  
Steel Plates ◽  
Strong Impact ◽  
Deformation Capacity ◽  
Initial Stiffness ◽  
Plane Shear ◽  
Floor Slabs ◽  
Strength And Deformation

Detailed formation of precast floor slab connectors has significant effect on their shear capacity, but there is no such specific provision on it at present. The effects of detailed formations on the shear strength, stiffness and deformation capacity of hairpin connectors(HPC) were studied, through numerical simulation analysis under in-plane shear force. The imbedded depth (d), slug length (h), steel plate thickness (t) and its stickout(s) were taken as parameters. The analysis results show that: ⅰ) the increase of imbedded depth can improve the bearing capacity and stiffness of HPC, but decrease the deformation capacity; ⅱ) with the increase of slug length, the HPC strength, stiffness and deformation capacity raised a lot; ⅲ) the steel plates’ thickness has small effect on the stiffness, but has strong impact on the strength and deformation capacity of HPC. ⅳ) the stickout can affect the initial stiffness and yield strength of HPC slightly, but has a considerable impact on its ultimate strength and deformation capacity. On the basis of analysis, recommendations on formation details of HPC are proposed for design and construction.

Mechanical Properties of Various Models of Interlocking Concrete Blocks under In-Plane and Out-of-Plane Loads

2021 ◽  
Vol 881 ◽  
pp. 149-156
Author(s):  
Mochamad Teguh ◽  
Novi Rahmayanti ◽  
Zakki Rizal
Keyword(s):  
Mechanical Properties ◽  
Building Material ◽  
Experimental Tests ◽  
Concrete Block ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Plane Shear ◽  
Out Of Plane ◽  
Concrete Blocks ◽  
Local Materials

Building material innovations in various interlocking concrete block masonry from local materials to withstand lateral earthquake forces is an exciting issue in masonry wall research. The block hook has an advantage in the interlocking system's invention to withstand loads in the in-plane and out-of-plane orientations commonly required by the masonry walls against earthquake forces. Reviews of the investigation of in-plane and out-of-plane masonry walls have rarely been found in previous studies. In this paper, the results of a series of experimental tests with different interlocking models in resisting the simultaneous in-plane shear and out-of-plane bending actions on concrete blocks are presented. This paper presents a research investigation of various interlocking concrete blocks' mechanical properties with different hook thicknesses. Discussion of the trends mentioned above and their implications towards interlocking concrete block mechanical properties is provided.

scholarly journals Comparative Analysis of the Energy Dissipation of Steel Buildings with Concentric and Eccentric Braces

2015 ◽  
Vol 9 (1) ◽  
pp. 295-307 ◽  
Author(s):  
Edelis del V. Marquez A. ◽  
William Lobo-Q ◽  
Juan C. Vielma
Keyword(s):  
Energy Dissipation ◽  
Shear Failure ◽  
Numerical Models ◽  
Deformation Energy ◽  
Seismic Zone ◽  
Deformation Capacity ◽  
Building Structures ◽  
Steel Buildings ◽  
High Deformation ◽  
Energy Dissipation Capacity

A comparative study has been done to analyze the behavior of regular steel building structures of 4, 6, 8 and 10 stories, located in seismic zone 5 and soil type S1. The structures were upgraded with different brace configurations according to current Venezuelan codes. A total number of 24 numerical models were analyzed considering non-linear static and incremental dynamic analysis (IDA). The buildings were initially designed as moment resisting frames, and upgraded with six different bracing configurations: concentric braces in “X” and inverted “V”; eccentric braces inverted "V" with horizontal links, inverted “Y” and “X” with vertical links. Short length links were used to ensure a shear failure. The used methodology is based on obtaining the capacity, IDA curves, and bilinear approximations of these curves that allow the determination of yield and ultimate capacity points, in order to estimate important parameters of seismic response: overstrength and ductility; and considering these areas under the curves to estimate elastic deformation energy, energy dissipated by hysteretic damping and equivalent damping. According to the results, the cases with no brace enhancement showed the lowest lateral strength and lateral stiffness and high deformation capacity. On the other hand, the concentric bracing cases, resulted with the highest stiffness and strength and the lowest deformation capacity, therefore they have low ductility and energy dissipation capacity under seismic loading. Structures with links showed intermediate stiffness and strengths, resulting in the best performance in terms of ductility and energy dissipation capacity. The present study provides a better understanding of the benefits of eccentrically braced systems.

scholarly journals Experimental Investigation on the Performance of Historical Squat Masonry Walls Strengthened by UHPC and Reinforced Polymer Mortar Layers

2019 ◽  
Vol 9 (10) ◽  
pp. 2096 ◽  
Author(s):  
Bin Peng ◽  
Sandong Wei ◽  
Libo Long ◽  
Qizhen Zheng ◽  
Yueqiang Ma ◽  
...  
Keyword(s):  
High Performance Concrete ◽  
Brick Masonry ◽  
Masonry Walls ◽  
Strengthening Effect ◽  
Plane Shear ◽  
Historical Building ◽  
Reinforced Polymer ◽  
Polymer Mortar ◽  
Historical Masonry ◽  
Squat Walls

Strengthening historical brick masonry walls is important because these walls are major load-bearing members in many architectural heritages. However, historical brick masonry has low elastic modulus and low strength, historical masonry walls are prone to surface treatment or other structural intervention, and some of the walls lack integrity. These characteristics make effective strengthening of historical masonry walls difficult. To address the issue, strengthening layers made up of ultra-high performance concrete (UHPC) are potentially useful. To investigate the strengthening effect of the UHPC layers, the authors constructed three squat walls using historical bricks and mortar collected from the rehabilitation site of a historical building, and strengthened two of the walls with a UHPC layer and a reinforced polymer mortar layer respectively. The three walls were broken down by horizontal cyclic force along with constant vertical compression, and then the unstrengthened one was strengthened in-situ by a UHPC layer and was tested again. The experimental results indicate that the UHPC layers significantly improved the in-plane shear resistance and cracking load of the squat walls, without decreasing the walls’ ultimate deformation. They effectively strengthened both moderately and severely damaged historical masonry walls, because the UHPC filled the existing damages and improved the integrity of the masonry substrate. In addition, the UHPC layers intervened the historical walls less than the reinforced polymer mortar layer. Therefore, the UHPC layers are efficient in strengthening historical squat masonry walls.

Shear Performance of FRP-Retrofitted Masonry Wall with Structural Columns

2015 ◽  
Vol 744-746 ◽  
pp. 288-291
Author(s):  
Zhen Lei ◽  
Yong Wang ◽  
Jun Tong Qu
Keyword(s):  
Shear Behavior ◽  
Masonry Wall ◽  
Fiber Reinforced Polymer ◽  
Masonry Walls ◽  
Lateral Shear ◽  
Maximum Displacement ◽  
Plane Shear ◽  
Damage Level ◽  
Reinforced Polymer ◽  
Shear Performance

To overcome the shortcoming of unreinforced masonry (URM) structure, structural columns are added in its construction to avoid the sudden collapse. This kind of structures still suffers different degrees of damage in the earthquake. This paper assesses the in-plane shear behavior of masonry walls with structural columns retrofitted with FRP (fiber reinforced polymer). The tests of two half-scaled masonry walls under cyclic loading have been carried out. One wall was served as reference specimen without any retrofitting scheme. Another specimen was tested to the pre-defined damage level and then strengthened with FRP sheets in mixed retrofitted configuration. The shear behavior of retrofitted specimen was discussed and compared with the reference in the aspect of lateral shear strength, maximum displacement and energy dissipation.

scholarly journals Experimental and Numerical Study of Behaviour of Reinforced Masonry Walls with NSM CFRP Strips Subjected to Combined Loads

Buildings ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 103
Author(s):  
Houria Hernoune ◽  
Benchaa Benabed ◽  
Antonios Kanellopoulos ◽  
Alaa Hussein Al-Zuhairi ◽  
Abdelhamid Guettala
Keyword(s):  
Failure Modes ◽  
Numerical Study ◽  
Masonry Wall ◽  
Brick Masonry ◽  
Masonry Walls ◽  
Near Surface ◽  
Combined Loads ◽  
Reinforced Masonry ◽  
Brick And Mortar ◽  
Near Surface Mounted

Near surface mounted (NSM) carbon fibers reinforced polymer (CFRP) reinforcement is one of the techniques for reinforcing masonry structures and is considered to provide significant advantages. This paper is composed of two parts. The first part presents the experimental study of brick masonry walls reinforced with NSM CFRP strips under combined shear-compression loads. Masonry walls have been tested under vertical compression, with different bed joint orientations 90° and 45° relative to the loading direction. Different reinforcement orientations were used including vertical, horizontal, and a combination of both sides of the wall. The second part of this paper comprises a numerical analysis of unreinforced brick masonry (URM) walls using the detailed micro-modelling approach (DMM) by means of ABAQUS software. In this analysis, the non-linearity behavior of brick and mortar was simulated using the concrete damaged plasticity (CDP) constitutive laws. The results proved that the application of the NSM-CFRP strips on the masonry wall influences significantly strength, ductility, and post-peak behavior, as well as changing the failure modes. The adopted DMM model provides a good interface to predict the post peak behavior and failure mode of unreinforced brick masonry walls.

Sign in / Sign up

Export Citation Format

Share Document