Effect of Re-Entrant and Toroidal Combustion Chambers in a DICI Engine

2015 ◽  
Vol 787 ◽  
pp. 722-726 ◽  
Author(s):  
Sozhi Arumugam ◽  
Pitchandi Kasivisvanathan ◽  
M. Arventh ◽  
P. Maheshkumar
Keyword(s):  
Carbon Monoxide ◽  
Combustion Chamber ◽  
Peak Pressure ◽  
Direct Injection ◽  
Compression Ignition ◽  
Oxides Of Nitrogen ◽  
Combustion Chambers ◽  
Brake Thermal Efficiency ◽  
Performance And Emissions ◽  
Toroidal Chamber

This paper presents the experimental work to investigate the effect of Re-entrant and Toroidal combustion chambers in a DICI Engine. The two combustion chambers namely Re-entrant combustion chamber (RCC) and Toroidal combustion chamber (TCC) were fitted in a 4.4 kW single cylinder Direct Injection Compression Ignition (DICI) engine and tests were conducted with diesel. The influences of the combustion chamber geometry characteristics on combustion, performance and emissions characteristics have been investigated. This investigation shows the peak pressure of re-entrant chamber is higher than that of toroidal chamber. The heat release rate and brake thermal efficiency for re-entrant chamber are slightly higher than that of toroidal chamber. Specific fuel consumption is lower for toroidal chamber than that of re-entrant chamber. The enhancement in reduction of carbon monoxide, hydrocarbon is observed for Re-entrant chamber compared to the Toroidal chamber. Oxides of nitrogen are reduced for toroidal chamber than that of re-entrant chamber.

Performance, Combustion and Emission Analysis for Various Combustion Chamber Geometry

2014 ◽  
Vol 984-985 ◽  
pp. 950-956
Author(s):  
S. Arumugam ◽  
N. Vasudevan ◽  
P. Saravanan ◽  
K. Pitchandi
Keyword(s):  
Combustion Chamber ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Specific Fuel Consumption ◽  
Oxides Of Nitrogen ◽  
Emission Analysis ◽  
Maximum Heat ◽  
Brake Thermal Efficiency ◽  
Performance And Emissions ◽  
Toroidal Chamber

The experimental work investigates performance, combustion and emission analysis for various combustion chamber geometry such as combustion, brake thermal efficiency, specific fuel consumption, and emission characteristics. The various combustion chamber namely Spherical chamber (SC), Toroidal chamber (TC), Re-entrant chamber (RC) were fitted in a 4.4 kW single cylinder air cooled Compression ignition (CI) engine and tests were conducted with standard diesel. The investigated of the combustion chamber geometry characteristics on combustion, performance and emissions. This investigation shows brake thermal efficiency for Re-entrant chamber and Toroidal chamber is slightly higher than Spherical chamber. And lower specific fuel consumption of Toroidal chamber, Re-entrant chamber than that of Spherical chamber. The enhancement in reduction of carbon monoxide, hydrocarbon is recorded for Re-entrant chamber compared to the Toroidal chamber and Spherical chamber. Oxides of nitrogen are reduced for Re-entrant chamber and Toroidal chamber than that of Spherical chamber. Combustion characteristics improved for Re-entrant chamber compared to Spherical chamber. The cylinder pressure for Re-entrant chamber and Toroidal chamber is higher than that of Spherical chamber. Also obtained maximum heat release rate for Re-entrant chamber than Toroidal chamber and Spherical chamber.

scholarly journals Performance and emissions of si engine with octane boosters

2018 ◽  
Vol 249 ◽  
pp. 03008
Author(s):  
Sai Vijay Venkatesh ◽  
R Udayakumar
Keyword(s):  
Carbon Dioxide ◽  
Carbon Monoxide ◽  
Emission Characteristics ◽  
Oxides Of Nitrogen ◽  
Performance Parameters ◽  
Si Engine ◽  
Brake Thermal Efficiency ◽  
Performance And Emission ◽  
Brake Power ◽  
Performance And Emissions

In today’s world we see that the demand for gasoline and cars keep increasing and one problem which is significantly seen is that we either opt for a fuel which provides higher performance or for a fuel which provides lesser emissions. In this study we aim to provide higher performance and lower emissions by combining two chemicals or octane boosters, namely ethanol and toluene with gasoline and find out its performance and emission characteristics when compared with traditional gasoline and ethanol-gasoline blend. In this study we have made four blends which are PP, E10, E10T5 and E20T5 which are tested against two performance parameters which are Specific Fuel Consumption, Brake Thermal Efficiency with respect to brake power and emissions parameter which are Carbon Dioxide, Carbon Monoxide, Oxides of Nitrogen and Hydrocarbon with respect to brake power as well. In each of these performance and emissions parameters, the blends are compared and we find that E20T5 has the highest performance and E10T5 has the lowest emission.

Experimental Investigation of Performance and Emissions Characteristics of a Diesel Engine with Pongamia Biodiesel and Diesel Blends

2018 ◽  
Vol 877 ◽  
pp. 397-402
Author(s):  
R. Thirunavukkarasu ◽  
R. Tamilselvan ◽  
T. Karthickmunisamy ◽  
M. Veeramanikandan ◽  
Dhandapani Sathish
Keyword(s):  
Experimental Investigation ◽  
Carbon Monoxide ◽  
Energy Consumption ◽  
The Other ◽  
Oxides Of Nitrogen ◽  
Brake Thermal Efficiency ◽  
Biodiesel Blends ◽  
Unburned Hydrocarbon ◽  
Performance And Emissions ◽  
Ci Engines

Biodiesel has been recognized as a possible alternative fuel for CI engines because use of biodiesel can reduce petroleum diesel consumption as well as engine out emissions. Out of many biodiesel derived from various resources, this biodiesel derived from Pongamia pinnata Oil (PPO) can be prepared economically using usual transesterification process. In the present study, in-depth research and comparative study of blends of biodiesel made from PPO and diesel is carried out to bring out the benefits of its extensive usage in CI engines. The experimental results of the study reveal that the PPO biodiesel has similar characteristics to that of diesel. The brake thermal efficiency, carbon monoxide, unburned hydrocarbon are observed to be lower in the case of PPO biodiesel blends than diesel. On the other hand specific fuel energy consumption and oxides of nitrogen of PPO biodiesel blends are found to be higher than diesel.

Decreasing hydrocarbon and carbon monoxide emissions of a natural-gas engine operating in the quasi-homogeneous charge compression ignition mode at low loads

2005 ◽  
Vol 219 (9) ◽  
pp. 1125-1131 ◽  
Author(s):  
Su Ling ◽  
Zhou Longbao ◽  
Liu Shenghua ◽  
Zhong Hui
Keyword(s):  
Carbon Monoxide ◽  
Natural Gas ◽  
Thermal Efficiency ◽  
Homogeneous Charge Compression Ignition ◽  
Compression Ignition ◽  
Brake Thermal Efficiency ◽  
Pilot Fuel ◽  
Cng Engine ◽  
Standard Mode ◽  
Homogeneous Charge

Experimental studies have been carried out on decreasing the hydrocarbon (HC) and carbon monoxide (CO) emissions of a compressed natural-gas (CNG) engine operating in quasi-homogeneous charge compression ignition (QHCCI) mode at low loads. The effects of three technical approaches including partial gas cut-off (PGC), intake air throttling, and increasing the pilot fuel quantity on emissions and the brake thermal efficiency of the CNG engine are studied. The results show that HC and CO emissions can be reduced with only a small penalty on the brake thermal efficiency. An increase in the brake thermal efficiency and reductions in HC and CO emissions can be simultaneously realized by increasing the pilot fuel quantity. It is also indicated from experiments that the HC and CO emissions of the engine can be effectively reduced when using intake air throttling and increasing the pilot fuel quantity are both adopted. However, nitrogen oxide (NOx) emissions increase with increase in the throttling and the pilot fuel quantity. Under PGC conditions, NOx emissions are lower than those in the standard mode; however, they increase and exceed the values in the standard mode in increases in the load and natural-gas supply.

An integrated effort of medium reactivity fuel, in-cylinder, and after-treatment strategies to demonstrate potential reduction in challenging emissions of reactivity controlled compression ignition combustion

2019 ◽  
Vol 234 (5) ◽  
pp. 1260-1278
Author(s):  
R Murugan ◽  
D Ganesh ◽  
G Nagarajan
Keyword(s):  
Carbon Monoxide ◽  
Direct Injection ◽  
Cetane Number ◽  
Combustion Process ◽  
Oxidation Catalyst ◽  
Compression Ignition ◽  
Reactivity Controlled Compression Ignition ◽  
Potential Reduction ◽  
Carbon Monoxide Emission ◽  
Compression Ignition Combustion

Previous studies on reactivity controlled compression ignition combustion indicated that, reducing the hydrocarbon and carbon monoxide emissions at low load conditions still remains a challenge because of lower in-cylinder temperatures due to lower global reactivity gradient and reduced oxidation process. Research in this direction has not been reported so far and with this motivation, an attempt has been made to increase the global reactivity gradient and oxidation of fuel–air mixture by converting the low reactivity fuel methanol into medium reactivity fuel. This is achieved by mixing high octane oxygenated fuel, methanol (Octane Number: 110), with an oxygenated better cetane and volatility fuels like polyoxymethylene dimethyl ether (Cetane Number: 78) and isobutanol (Cetane Number: 15). The medium reactivity fuel with multiple direct injection of diesel fuel timed the combustion of dual fuel–air mixture to avoid too late or too advanced combustion which are the prime factors in controlling the unburnt emissions in a low temperature combustion process. Four medium reactivity fuel samples, M80IB20, M60IB40, M90P10, and M80P20, on percentage volume basis have been prepared and tested on the modified on-road three-cylinder turbocharged common rail direct injection diesel engine to demonstrate higher indicated thermal efficiency and potential reduction in unburnt and oxides of nitrogen/particulate matter emissions from reactivity controlled compression ignition combustion. Experimental results show that, use of medium reactivity fuel with optimized diesel injection strategy resulted in 66% decrease in hydrocarbon emission and 74% decrease in carbon monoxide emission by enhancing the oxidation of fuel–air mixture at lower temperatures which is evidently noticed in the combustion characteristics. Further reduction in hydrocarbon and carbon monoxide emission of about 90% has been achieved by integrating the diesel oxidation catalyst with the engine.

Design and Manufacturing of a Constant Volume Test Combustion Chamber for Jet and Flame Visualization of CNG Direct Injection

2012 ◽  
Vol 217-219 ◽  
pp. 2539-2545 ◽  
Author(s):  
Alireza Hajialimohammadi ◽  
Saeed Ahmadisoleymani ◽  
Amir Abdullah ◽  
Omid Asgari ◽  
Foad Rezai
Keyword(s):  
Finite Element ◽  
Combustion Chamber ◽  
High Speed ◽  
Direct Injection ◽  
Constant Volume ◽  
Ease Of Use ◽  
Diagnostic Methods ◽  
High Speed Photography ◽  
Combustion Chambers ◽  
Element Analysis

Constant volume transparent test combustion chambers are extensively used for investigating injection and fuel burning properties of various combustion engines. Their configuration depends on the engine type and the research purpose. Material of components, shape and dimensions of the chamber and its parts, ease of use, accessibility, sealing and safety of the assembly are the parameters needed to be considered in designing the test cell. This paper explains, structural design of a test combustion chamber and its optical windows using finite element analysis of ANSYS 12.0 software for bearing high pressure variations and thermal shocks of combustion. It was designed for conducting CNG direct injection study on direct injection SI CNG engines for maximum design pressure of 100 bars. Optical diagnostic methods and high speed photography through quartz windows are used for the jet and flame developments. Satisfactory test results of the fabricated system proved that the finite element method can successfully be employed for design of such a system.

scholarly journals Experimental investigation on combustion, performance, and emissions characteristics of butanol as an oxygenate in a spark ignition engine

2017 ◽  
Vol 9 (2) ◽  
pp. 168781401668884 ◽  
Author(s):  
Yu Li ◽  
Jinke Gong ◽  
Wenhua Yuan ◽  
Jun Fu ◽  
Bin Zhang ◽  
...  
Keyword(s):  
Carbon Monoxide ◽  
Nitrogen Oxides ◽  
Thermal Efficiency ◽  
Alternative Fuel ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Combustion Performance ◽  
Performance And Emissions ◽  
Unburned Hydrocarbons

Ethanol is known as the most widely used alternative fuel for spark-ignition engines. Compared to it, butanol has proved to be a very promising renewable fuel in recent years for desirable properties. The conjoint analysis on combustion, performance, and emissions characteristics of a port fuel injection spark-ignition engine fueled with butanol–gasoline blends was carried out. In comparison with butanol–gasoline blends with various butanol ratio (0–60 vol% referred as G100~B60) and conventional alcohol alternative fuels (methanol, ethanol, and butanol)–gasoline blends, it shows that B30 performs well in engine performance and emissions, including brake thermal efficiency, brake-specific fuel consumption, carbon monoxide, unburned hydrocarbons, and nitrogen oxides. Then, B30 was compared with G100 under various equivalence ratios ( Φ = 0.83–1.25) and engine loads (3 and 5-bar brake mean effective pressure). In summary, B30 presents an advanced combustion phasing, which leads to a 0.3%–2.8% lower brake thermal efficiency than G100 as the engine was running at the spark timing of gasoline’s maximum brake torque (MBT). Therefore, the sparking timing should be postponed when fueled with butanol–gasoline blends. For emissions, the lower carbon monoxide (2.3%–8.7%), unburned hydrocarbons (12.4%–27.5%), and nitrogen oxides (2.8%–19.6%) were shown for B30 compared with G100. Therefore, butanol could be a good alternative fuel to gasoline for its potential to improve combustion efficiency and reduce pollutant emissions.

Effect of Combustion Chamber Geometry on Performance and Emission Characteristics of a Diesel Engine Fueled with Mahua Biodiesel Blends

2014 ◽  
Vol 984-985 ◽  
pp. 900-906
Author(s):  
L. Saravanakumar ◽  
B.R. Ramesh Bapu ◽  
B. Durga Prasad
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Emission Characteristics ◽  
Oxides Of Nitrogen ◽  
Plant Oil ◽  
Brake Thermal Efficiency ◽  
Performance And Emission ◽  
Standard Configuration ◽  
Mahua Biodiesel ◽  
High Fatty Acids

The present work investigates the effect of change in combustion chamber geometry on performance and emission characteristics of single cylinder diesel engine fuelled with mahua biodiesel. Since plant oil derived from the mahua tree has high fatty acids, it undergoes esterification followed by transesterification process to reduce its viscosity. Experiments were conducted using a blend of 20% biodiesel (B20) 40% biodiesel (B40) with diesel and compared with diesel by using two types of combustion chamber geometry, explicitly hemispherical and modified hemispherical combustion chamber. Performance parameters such as Brake Thermal Efficiency (BTE), Brake Specific Fuel Consumption (BSFC) and emission parameters like Unburned Hydro Carbon (UBHC), Oxides of Nitrogen (NOx) were studied from the diesel engine with above mentioned configurations. It is obvious that there is considerable improvement in the performance parameter viz, BTE, BSFC and reduction in UBHC emissions by using the modified geometry piston. However, the NOx emission was found to be higher than that of standard configuration. The results obtained from the blend B20 at modified combustion chamber geometry are on par with diesel and hence mahua biodiesel can be suggested as an alternative fuel for Compression Ignition (C.I) engine with modified combustion chamber geometry.

Fast-Burn Combustion Chamber Design for Natural Gas Engines

1998 ◽  
Vol 120 (1) ◽  
pp. 232-236 ◽  
Author(s):  
R. L. Evans ◽  
J. Blaszczyk
Keyword(s):  
Combustion Chamber ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Performance Parameters ◽  
Combustion Chambers ◽  
Natural Gas Engines ◽  
Chamber Design ◽  
Performance And Emissions ◽  
Unburned Hydrocarbons ◽  
Fuel Mixtures

The work presented in this paper compares the performance and emissions of the UBC “Squish-Jet” fast-burn combustion chamber with a baseline bowl-in-piston (BIP) chamber. It was found that the increased turbulence generated in the fastburn combustion chambers resulted in 5 to 10 percent faster burning of the air–fuel mixture compared to a conventional BIP chamber. The faster burning was particularly noticeable when operating with lean air–fuel mixtures. The study was conducted at a 1.7 mm clearance height and 10.2:1 compression ratio. Measurements were made over a range of air–fuel ratios from stoichiometric to the lean limit. At each operating point all engine performance parameters, and emissions of nitrogen oxides, unburned hydrocarbons, and carbon monoxide were recorded. At selected operating points a record of cylinder pressure was obtained and analyzed off-line to determine mass-burn rate in the combustion chamber. Two piston designs were tested at wide-open throttle conditions and 2000 rpm to determine the influence of piston geometry on the performance and emissions parameters. The UBC squish-jet combustion chamber design demonstrates significantly better performance parameters and lower emission levels than the conventional BIP design. Mass-burn fraction calculations showed a significant reduction in the time to burn the first 10 percent of the charge, which takes approximately half of the time to burn from 10 to 90 percent of the charge.

Sign in / Sign up

Export Citation Format

Share Document