Monte Carlo Simulation of the Torsional Strength due to Concrete Compression of Reinforced Concrete Element

2015 ◽  
Vol 797 ◽  
pp. 27-34 ◽  
Author(s):  
Roman Jaskulski ◽  
Piotr Wiliński
Keyword(s):  
Compressive Strength ◽  
Monte Carlo ◽  
Reinforced Concrete ◽  
Cross Sections ◽  
Safety Margin ◽  
Strength Distribution ◽  
Distribution Functions ◽  
Concrete Compressive Strength ◽  
Concrete Element ◽  
Torsional Resistance

The aim of the work was to assess the safety margin of reinforced concrete element of rectangular cross-sections subjected to torsion. In the performed analyses two models of torsional resistance based on concrete compressive strength was taken into account. Assessment was performed with use of Monte Carlo method. Utilized models of shear resistance were taken from formerly used Polish standards: PN-84/B-03264, PN-B-03264:2002 and the actual Polish standard EN-1992-1-1:2004. From the same standards necessary assumptions related with the models were taken. The safety margin and influence of the differences in assumptions on the obtained results were analyzed. The selected models was also evaluated in terms of their “sensitivity” to changes of basic parameters of distribution functions of selected random variables. Results showed that average torsional resistance differs of about 50% times depending of assumed model. The reliability level, measured with the partial reliability exponent ΔR, differs of 10% if different models are concerned but the differences are much higher (up to 5 times, when the standard deviation of concrete compressive strength distribution changes).

Probabilistic Analysis of Shear Resistance due to Concrete Tension

2015 ◽  
Vol 797 ◽  
pp. 35-44 ◽  
Author(s):  
Roman Jaskulski ◽  
Piotr Wiliński
Keyword(s):  
Monte Carlo ◽  
Cross Sections ◽  
Safety Margin ◽  
Shear Resistance ◽  
Distribution Functions ◽  
European Standard ◽  
Reliability Level ◽  
Average Shear ◽  
Basic Parameters ◽  
Tension Strength

The aim of the work was to assess the safety margin of reinforced rectangular concrete cross-sections subjected to shear. In the performed analyses models of shear resistance based on concrete tension strength was taken into account. Assessment was performed with use of Monte Carlo method. Utilized models of shear resistance were taken from formerly used Polish standards: PN-84/B-03264, PN-B-03264:2002 and the European standard EN-1992-1-1:2004. From the same standard necessary assumptions related with the models were taken. The safety margin and influence of the differences in assumptions on the obtained results were analyzed. The selected models was also evaluated in terms of their “sensitivity” to changes of basic parameters of distribution functions of selected random variables. Results showed that average shear resistance differs about 3 times depending of assumed model of the shear resistance and the reliability level, measured with the partial reliability exponent ΔR, differs 4-7 times.

RELIABILITY ANALYSIS OF REINFORCED CONCRETE FLEXURAL ELEMENT ON CRACKING BASED ON FRACTURE MECHANICS

2020 ◽  
pp. 40-44
Author(s):  
S. A. Solov’ev ◽  
O. V. Yarygina
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Stress Intensity ◽  
Fracture Mechanics ◽  
Reliability Analysis ◽  
Critical Stress ◽  
Intensity Coefficient ◽  
Concrete Compressive Strength ◽  
Concrete Element ◽  
Stress Intensity Coefficient

The article describes a probabilistic approach to the reliability analysis of a flexural reinforced concrete element by the cracking criterion using the provisions of fracture mechanics. Two mathematical models of limit state are proposed for reliability analysis: with the evaluation of the critical stress intensity coefficient directly and through the design concrete compressive strength. On the basis of regression analysis, the relationship between the critical stress intensity coefficient and the design concrete compressive strength is established which can be used in the inspection of reinforced concrete structural elements. The influence of the design concrete compressive strength on the failure (cracking) probability of the flexural reinforced concrete element is analyzed. The numerical example of reliability analysis is given for the reinforced concrete beam by the criterion of cracking. It is noted that the required level of reliability should be set for each structural object individually based on the acceptable risk value using economic and non-economic losses.

Guidelines for flexural design of FRP reinforced concrete beams

2020 ◽  
pp. 002199832097373
Author(s):  
Fares Jnaid
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Large Diameter ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Concrete Compressive Strength ◽  
Load Carrying ◽  
Multiple Variables

This paper investigates the effects of different parameters on the live load carrying capacity of concrete beams reinforced with FRP bars. The author performed a parametric study utilizing an innovative numerical approach to inspect the effects of multiple variables such as reinforcement ratio, concrete compressive strength, span to depth ratio, FRP type, and bar diameter on load carrying capacity of FRP reinforced concrete beams. This study concluded that unless the span to height ratio is smaller than 8, tension-controlled sections are impractical as they do not meet code requirements for serviceability. In addition, it is recommended to use higher reinforcement ratios when using larger span to depth ratios and/or when using CFRP reinforcing bars. Moreover, larger number of bars with small diameter is more practical than fewer large diameter bars. Furthermore, this research suggests that increasing the concrete compressive strength is associated with a significant increase in the ultimate flexural capacity of FRP reinforced beams.

Analysis of the Impact of Concrete Compressive Strength Reduction in Joint Core Area on Super High-Rise Structures

2013 ◽  
Vol 438-439 ◽  
pp. 690-695
Author(s):  
Xiao Yu ◽  
Na Wu ◽  
Zhao Yang ◽  
Kai Xu
Keyword(s):  
Compressive Strength ◽  
Cross Sections ◽  
Concrete Strength ◽  
Nonlinear Finite Element ◽  
Core Area ◽  
Concrete Compressive Strength ◽  
Element Analysis ◽  
High Rise ◽  
The Impact ◽  
Joint Core Area

t is focused on a super high-rise building structure, of which the concrete compressive strength is reduced in joint core. The whole structure is calculated with program SATWE. Based on this calculation, integral stress analysis by MIDAS when concrete strength is reduced in joint core area and nonlinear finite element analysis by ANSYS on the joints of the worst cross-sections in the whole structure are developed. Thus the adverse effect of reduced concrete strength in joint core area on super high-rise structures is found out.

Analysis and Prospect of Size Effect on Normal Section Bearing Capacity of Reinforced Concrete Column

2013 ◽  
Vol 351-352 ◽  
pp. 422-426
Author(s):  
Yong Ping Xie ◽  
Lei Jia ◽  
Gang Sun
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Theoretical Analysis ◽  
Size Effect ◽  
Bearing Capacity ◽  
Concrete Column ◽  
Concrete Compressive Strength ◽  
Reinforced Concrete Column ◽  
Normal Section

With the development of modern constructional technique, more attention on the size effect is paid by academics and engineers. The normal section bearing capacity of Reinforced Concrete Column is analyzed by eccentrically compressed theory firstly. The size effect on normal section bearing capacity of reinforced concrete column is obtained by theoretical analysis and experimental summary. The size effect formula of concrete compressive strength is proposed. Finally, a research thinking of size effect on bearing capacity is suggested.

scholarly journals Construction of N-M Interaction Diagram for Reinforced Concrete Columns Strengthened with Steel Jackets Using Plastic Stress Distribution Method

2017 ◽  
Vol 3 (10) ◽  
pp. 929
Author(s):  
Mohannad Husain Al-Sherrawi ◽  
Hamza M. Salman
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Stress Distribution ◽  
Concrete Columns ◽  
Concrete Compressive Strength ◽  
Distribution Method ◽  
Reinforced Concrete Columns ◽  
Interaction Diagram ◽  
Steel Angle ◽  
Plastic Stress

No attempts have been made in developing the N-M interaction diagram for reinforced concrete columns strengthened with steel jackets using the plastic stress distribution method. Therefore, this paper presents an analytical model to construct the N-M interaction diagram for reinforced concrete columns strengthened with steel jackets using the plastic stress distribution method after assuming the behavior of strengthened column to be like composite column and including the effects of confinement on concrete compressive strength. The proposed model was compared with experimental results. The comparisons showed that the model is conservative and it reveals the ultimate strength of the strengthened column. A parametric study has been also carried out to investigate the influence of various parameters on the N-M interaction diagram of the strengthened column. These parameters were: dimensions of steel angle, yield stress of the steel angles, concrete compressive strength and the size of the reinforcement bars used in RC columns. The results made clear the effects of these parameters on the N-M interaction diagram, and encouraged the use of the model in preliminary strengthening studies.

scholarly journals Research on compressive strength of hybrid fiber reinforced concrete based on orthogonal design

2021 ◽  
Vol 261 ◽  
pp. 02019
Author(s):  
Tu-Sheng He ◽  
Meng-Qian Xie ◽  
Yang Liu ◽  
San-Yin Zhao ◽  
Zai-Bo Li
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Prediction Model ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Polypropylene Fiber ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Concrete Compressive Strength ◽  
Hybrid Fiber

The influence of steel fiber and polypropylene fiber mixed on compressive strength of high performance concrete (HPC) was studied. The steel fiber content (0.5%, 1.0%, 1.5%, 2.0%) (volume fraction, the same below), polypropylene fiber content (0.05%, 0.1%, 0.15%, 0.2%) and length (5mm, 6.5mm, 12mm, 18mm) were studied by L16 (45) orthogonal test for 28d ages, the range analysis and variance analysis of the test results are carried out, and the prediction model of compressive strength of hybrid fiber reinforced concrete was established. The results show that: The significant influence factor of concrete compressive strength is the volume fraction of polypropylene fiber, while the length of polypropylene fiber and the volume fraction of steel fiber are not significant; the concrete compressive strength with polypropylene fiber shows negative hybrid effect; The prediction model of compressive strength of hybrid fiber reinforced concrete has high accuracy, and the average relative errors is 2.96%.

Influence of Minimum Tension Steel Reinforcement on the Behavior of Singly Reinforced Concrete Beams in Flexure

2020 ◽  
Vol 38 (7A) ◽  
pp. 1034-1046
Author(s):  
Ali ِA. Abdulsada ◽  
Raid I. Khalel ◽  
Kaiss F. Sarsam
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Rectangular Cross Section ◽  
Steel Reinforcement ◽  
Reinforced Concrete Beams ◽  
Concrete Compressive Strength ◽  
Minimum Reinforcement ◽  
Flexural Reinforcement ◽  
New Formula

The requirements of minimum flexural reinforcement in the last decades have been a reason for controversy. The structural behavior of beams in bending is the best way of investigating and evaluating the minimum reinforcement in flexure. For this purpose, twelve singly reinforced concrete beams with a rectangular cross-section of (125 mm) width by (250 mm) height and (1800 mm) length were cast and tested under two-point loads up to failure. These beams were divided into three groups with different compressive strengths (25, 50, and 80 MPa). Each group consists of four beams with different amounts of tension steel reinforcement approximately equal to (0% Asmin, 50% Asmin, 100% Asmin and 150% Asmin), two bar diameters (Ø6 mm and Ø8 mm) were used as the longitudinal tension reinforcement with different yield and ultimate strengths, the minimum amount of reinforcement required is calculated based on ACI 318M-2014 code. The results show that for the reinforced concrete beams, the flexural reinforcement in NSC beams increases the first cracking load and the increment increased with an increasing amount of reinforcement, while for HSC beams the increasing in first cracking load are very little when the quantity of reinforcement less than the minimum flexural reinforcement and increased with the increasing amount above the minimum flexural reinforcement. The equation of ACI 318M-14 code gives adequate minimum flexural reinforcement for NSC and overestimate value for HSC up to (83 MPa), A new formula is proposed for HSC rectangular beams up to (90 MPa) concrete compressive strength by reducing the equation of ACI 318M-14 code for minimum flexural reinforcement by a factor depending on concrete compressive strength.  

An experimental study on cyclic behaviour of reinforced concrete connections

2007 ◽  
Vol 34 (4) ◽  
pp. 565-575 ◽  
Author(s):  
Gerson Moacyr Sisniegas Alva ◽  
Ana Lúcia Homce de Cresce El Debs ◽  
Mounir Khalil El Debs
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Cyclic Loading ◽  
Seismic Analysis ◽  
Reinforcement Rate ◽  
Shear Capacity ◽  
Transverse Reinforcement ◽  
Rc Beam ◽  
Concrete Compressive Strength ◽  
Cyclic Behaviour

Beam-column joints are considered critical regions within the structural system — especially under seismic loading — requiring careful design. Results from tests on four exterior reinforced concrete (RC) beam-column subassemblages are presented in this paper as part of an experimental investigation on the behaviour of RC beam-column connections under reversal cyclic loading. The influence of joint transverse reinforcement rate and concrete compressive strength on the RC beam-column connection behaviour was investigated. It is concluded that concrete compressive strength is the major factor that governs the joint shear capacity. The experimental results also indicated that joint transverse reinforcement affects the load-displacement response of such connections.Key words: cyclic loading, seismic analysis, reinforced concrete structures, beam-column connection.

Sign in / Sign up

Export Citation Format

Share Document