The Study on the Precipitation Behavior of the Second Phase Particles for As-Hot Rolled Dual-Phase Nb-Bearing Steel

2011 ◽  
Vol 189-193 ◽  
pp. 626-629
Author(s):  
Zhang Hong Mei ◽  
Qiao Li Feng
Keyword(s):  
Bearing Steel ◽  
Second Phase ◽  
Dual Phase ◽  
Precipitation Behavior ◽  
Extraction Replica ◽  
Carbon Extraction Replica ◽  
Heating And Cooling ◽  
Second Phase Particles ◽  
The Matrix ◽  
Hot Rolled

The precipitation behavior of the second phase particles was observed and studied by a carbon extraction replica technique used transmission electron microscopy (TEM) for Nb-bearing dual-phase steel. It is found that there are more second phase particles on the surface than that of in the center of sample. The mainly smaller particle which sizes of is below 20nm show the shape of spherical and ellipse. The sizes of larger particles are range of 20nm~40nm and the shape of them present rectangle or ellipse. The particles are dispersed on the matrix and the particle boundary is clear. The precipitate composition of particles are all Nb(C、N) examined by energy dispersive X-ray (EDX). The results of microstructure shows that the second phase particles pinned on grain boundary not only can inhibited the grain growth, but also the grain can be fined during the heating and cooling course.

The Study on the Precipitation Behavior of the Second Phase Particles for Fine Grain and High Strength IF Steel

2012 ◽  
Vol 217-219 ◽  
pp. 411-414
Author(s):  
Hong Mei Zhang ◽  
Li Feng Qiao ◽  
Qin Bo Liu
Keyword(s):  
Grain Boundary ◽  
High Strength ◽  
Second Phase ◽  
If Steel ◽  
Precipitation Behavior ◽  
Extraction Replica ◽  
Carbon Extraction Replica ◽  
Fine Grain ◽  
Second Phase Particles ◽  
Precipitate Composition

The new type SFG HSS (super fine grain, high strength steel sheet) has been developed by adding solid-solution strengthening elements to conventional IF steel such as Si, Mn. The precipitation behavior of the second phase particles was observed and studied by a carbon extraction replica technique used transmission electron microscopy (TEM). The shape of the small second particles is similar to spherical and ellipse, the sizes of which are 10~30nm. It is seen that the particles are dispersed on the matrix. The precipitate composition of small particles is Nb (CN) and the precipitate composition of large particles is NbC examined by energy dispersive X-ray (EDX). It is noted that the yield strength is low as well as the tensile strength is high by the PFZ which is free of precipitate called precipitated free zone on the one side of the grain boundary. The results of microstructure shows that the second phase particles pinned on grain boundary not only can inhibit the grain growth, but also the grain can be fined.

The Effect of Large Reduction on the Microstructure and Properties for As-Hot Rolled Dual-Phase Nb-Bearing Steel

2011 ◽  
Vol 284-286 ◽  
pp. 1101-1105
Author(s):  
Hong Mei Zhang ◽  
Li Feng Qiao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Dual Phase Steel ◽  
Bearing Steel ◽  
Dual Phase ◽  
Large Reduction ◽  
Microstructure Refinement ◽  
The Matrix ◽  
Hot Rolled

The effect of reduction on the microstructure refinement and mechanical properties of the as-hot rolled dual-phase Nb-bearing steel were studied at laboratory. It is found that the dual-phase steel displays clearly classic dual phase morphology which is ferrite and martensite or bainsite, and the fine island or lath martinsite is dispersed on the matrix of ferrite by the observation of microstructure. The grain can be refined, and the increased precipitated second particles are fined and dispersed with the increasing of reduction. The mechanical properties determination result shows that the mechanical properties have greatly improved by large reduction. The tensile strength obtained in the laboratory is up to 680MPa, the ratio of yield strength and tensile strength is low, and the elongation is better.

The Role of Metallurgical Solid State Phase Transformations on the Formation of Residual Stress in Laser Cladding and Heating

2014 ◽  
Vol 777 ◽  
pp. 19-24 ◽  
Author(s):  
Ryan Cottam ◽  
Vladimir Luzin ◽  
Kevin Thorogood ◽  
Yat C. Wong ◽  
Milan Brandt
Keyword(s):  
Residual Stress ◽  
Solid State ◽  
Phase Transformations ◽  
Contour Method ◽  
Second Phase ◽  
Heating And Cooling ◽  
Second Phase Particles ◽  
The Matrix ◽  
Packing Arrangement

There are two major types of solid state phase transformations in metallic materials; the formation of second phase particles during heat treatments, and the transformation of the matrix from one crystalline packing arrangement to another during either heating or cooling. These transformations change the spacing between adjacent atoms and can thus influence the residual stress levels formed. The heating and cooling cycles of materials processing operations using lasers such as cladding and melting/heating, can induce phase transformations depending on the character of the material being processed. This paper compares the effects of the different phase transformations and also the influence of the type of laser processing on the final residual stress formed. The comparisons are made between laser clad AA7075, laser clad Ti-6Al-4V and laser melted nickel-aluminium bronze using neutron diffraction and the contour method of measuring residual stress.

Polishing process effect on the image of dispersed precipitates

1984 ◽  
Vol 42 ◽  
pp. 534-535
Author(s):  
C.T. Hu ◽  
C.W. Allen
Keyword(s):  
Matrix Material ◽  
Specimen Preparation ◽  
Second Phase ◽  
Precipitate Particle ◽  
Polishing Process ◽  
Second Phase Particles ◽  
The Matrix ◽  
Surface Profiles ◽  
Thinning Process

One important problem in determination of precipitate particle size is the effect of preferential thinning during TEM specimen preparation. Figure 1a schematically represents the original polydispersed Ni3Al precipitates in the Ni rich matrix. The three possible type surface profiles of TEM specimens, which result after electrolytic thinning process are illustrated in Figure 1b. c. & d. These various surface profiles could be produced by using different polishing electrolytes and conditions (i.e. temperature and electric current). The matrix-preferential-etching process causes the matrix material to be attacked much more rapidly than the second phase particles. Figure 1b indicated the result. The nonpreferential and precipitate-preferential-etching results are shown in Figures 1c and 1d respectively.

Recrystallization in Ultra-Fine Grain Structures of AA3104 Alloy Processed by ECAP and HPT

2012 ◽  
Vol 715-716 ◽  
pp. 346-353
Author(s):  
H. Paul ◽  
T. Baudin ◽  
K. Kudłacz ◽  
A. Morawiec
Keyword(s):  
High Pressure Torsion ◽  
Deformation Mode ◽  
Second Phase ◽  
Orientation Measurement ◽  
Angular Pressing ◽  
Second Phase Particles ◽  
Average Grain Size ◽  
The Matrix ◽  
Electron Microscopes ◽  
Different Strains

The objective of this study was to determine the effect of deformation mode on recrystallization behavior of severely deformed material. Commercial purity AA3104 aluminum alloy was deformed via high pressure torsion and equal channel angular pressing to different strains and then annealed to obtain the state of partial recrystallization. The microstructure and the crystallographic texture were analysed using scanning and transmission electron microscopes equipped with orientation measurement facilities. The nucleation of new grains was observed in bulk recrystallized samples and during in-situ recrystallization in the transmission microscope. Irrespective of the applied deformation mode, a large non-deformable second phase particles strongly influenced strengthening of the matrix through deformation zones around them. It is known that relatively high stored energy stimulates the nucleation of new grains during the recrystalization. In most of the observed cases, the growth of recrystallized grains occurred by the coalescence of neighboring subcells. This process usually led to nearly homogeneous equiaxed grains of similar size. The diameter of grains in the vicinity of large second phase particles was only occasionally significantly larger than the average grain size. Large grains were most often observed in places far from the particles. TEM orientation mapping from highly deformed zones around particles showed that orientations of new grains were not random and only strictly defined groups of orientations were observed.

Microstructure of Friction Stir Processed Mg-Y-Zn Alloy

2007 ◽  
Vol 558-559 ◽  
pp. 777-780 ◽  
Author(s):  
Taiki Morishige ◽  
Masato Tsujikawa ◽  
Sung Wook Chung ◽  
Sachio Oki ◽  
Kenji Higashi
Keyword(s):  
Equal Channel Angular Extrusion ◽  
Second Phase ◽  
Ingot Metallurgy ◽  
Friction Stir ◽  
Fine Grained ◽  
Probe Diameter ◽  
Fine Grain ◽  
Second Phase Particles ◽  
The Matrix ◽  
Zn Alloy

Friction stir processing (FSP) is the effective method of the grain refinement for light metals. The aim of this study is to acquire the fine grained bulk Mg-Y-Zn alloy by ingot metallurgy route much lower in cost. Such bulk alloy can be formed by the superplastic forging. The microstructure of as-cast Mg-Y-Zn alloy was dendrite. The dendrite arm spacing was 72.5 [(m], and there are the lamellar structures in it. FSP was conducted on allover the plate of Mg-Y-Zn alloy for both surfaces by the rotational tool with FSW machine. The stirring passes were shifted half of the probe diameter every execution. The dendrite structures disappeared after FSP, but the lamellar structure could be observed by TEM. The matrix became recrystallized fine grain, and interdendritic second phase particles were dispersed in the grain boundaries. By using FSP, cast Mg-Y-Zn alloy could have fine-grained. This result compared to this material produced by equal channel angular extrusion (ECAE) or rapid-solidified powder metallurgy (RS P/M). As the result, as-FSPed material has the higher hardness than materials produced by the other processes at the similar grain size.

Preparation of Nano Ti3SiC2/MoSi2 Composite by SPS Process

2011 ◽  
Vol 284-286 ◽  
pp. 2414-2419 ◽  
Author(s):  
Jun Cai Zhang ◽  
Cheng Chang Jia
Keyword(s):  
Mechanical Activation ◽  
Particle Diameter ◽  
Second Phase ◽  
Strong Restriction ◽  
Matrix Surface ◽  
Second Phase Particles ◽  
The Matrix ◽  
Strong Repulsion

In this paper, nano-Ti3SiC2/MoSi2 composite, whose second phase was 20-150nm, was in situ prepared by mechanical activation (MA) and SPS process with the quaternary powers of Mo, Si, Ti, and C. The results showed that: (1) matrix MoSi2 has strong repulsion to other elements, which leads to more second-phase particles inside the matrix rather than on the matrix surface; (2) matrix MoSi2 has strong restriction on the growing of the second phase, which makes the particle diameter of the second phase inside the matrix only in 200 nm around, while that over the surface reaches to 800 nm around.

The Room Temperature and Elevated Temperature Fracture Toughness Response of Alloy A-286

1978 ◽  
Vol 100 (2) ◽  
pp. 195-199 ◽  
Author(s):  
W. J. Mills
Keyword(s):  
Fracture Toughness ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Second Phase ◽  
Surface Micromorphology ◽  
Second Phase Particles ◽  
The Matrix ◽  
Temperature Fracture ◽  
Increasing Temperature ◽  
Base Superalloy

The elastic-plastic fracture toughness (JIc) response of precipitation strengthened Alloy A-286 has been evaluated by the multi-specimen R-curve technique at room temperature, 700 K (800°F) and 811 K (1000°F). The fracture toughness of this iron-base superalloy was found to decrease with increasing temperature. This phenomenon was attributed to a reduction in the materials’s strength and ductility at elevated temperatures. Electron fractographic examination revealed that the overall fracture surface micromorphology, a duplex dimple structure coupled with stringer troughs, was independent of test temperature. In addition, the fracture resistance of Alloy A-286 was found to be weakened by the presence of a nonuniform distribution of second phase particles throughout the matrix.

Characteristics of Deposition Precipitation Process in Production of High Strength and Low Carbon Steel in FTSR

2014 ◽  
Vol 886 ◽  
pp. 128-131
Author(s):  
Zhuo Fei Song ◽  
Shan Shan Feng ◽  
Yun Li Feng
Keyword(s):  
Solid State ◽  
Low Carbon Steel ◽  
High Strength ◽  
Dynamical Analysis ◽  
Precipitation Process ◽  
Second Phase ◽  
Low Carbon ◽  
Second Phase Particles ◽  
Thermodynamics And Dynamics ◽  
Hot Rolled

Precipitation characteristics of second phase in HSLC steel produced by FTSR technology have been researched by TEM and EDS in this article. And preliminary research of precipitation conditions of second phase particles in thermodynamics and dynamics have been took. The results indicate that: there’re second phase particles precipitated dispersively in hot rolled HSLC steels by FTSR technology. These particles mainly contain particles of Al2O3、MnS and AlN. Thermo dynamical analysis declares that most of the Al2O3 and all of the MnS、 AlN particles are precipitated in solid state. That’s why the precipitation process is slowed down by the diffusion velocity of the elements in solid, and thinner particles are precipitated while the material is in solid state than in liquid state.

Sign in / Sign up

Export Citation Format

Share Document