Preparation of Nano Ti3SiC2/MoSi2 Composite by SPS Process

2011 ◽  
Vol 284-286 ◽  
pp. 2414-2419 ◽  
Author(s):  
Jun Cai Zhang ◽  
Cheng Chang Jia
Keyword(s):  
Mechanical Activation ◽  
Particle Diameter ◽  
Second Phase ◽  
Strong Restriction ◽  
Matrix Surface ◽  
Second Phase Particles ◽  
The Matrix ◽  
Strong Repulsion

In this paper, nano-Ti3SiC2/MoSi2 composite, whose second phase was 20-150nm, was in situ prepared by mechanical activation (MA) and SPS process with the quaternary powers of Mo, Si, Ti, and C. The results showed that: (1) matrix MoSi2 has strong repulsion to other elements, which leads to more second-phase particles inside the matrix rather than on the matrix surface; (2) matrix MoSi2 has strong restriction on the growing of the second phase, which makes the particle diameter of the second phase inside the matrix only in 200 nm around, while that over the surface reaches to 800 nm around.

Continuous and Discontinuous Recrystallization of 6013 Aluminum Alloy

2013 ◽  
Vol 753 ◽  
pp. 221-224 ◽  
Author(s):  
Krzysztof Sztwiertnia ◽  
Magdalena Bieda ◽  
Anna Korneva
Keyword(s):  
Aluminum Alloy ◽  
Grain Boundaries ◽  
Second Phase ◽  
Sheet Plane ◽  
Temperature Range ◽  
Orientation Mapping ◽  
Second Phase Particles ◽  
The Matrix ◽  
Continuous Recrystallization

In situ orientation mapping using TEM and calorimetric measurements were carried out to investigate the annealing behavior of cold-rolled 6013 aluminum alloy. The recrystallization of the material can be considered to be a number of processes that correspond to two separate stored energy release peaks. In the temperature range of the peak 1, the deformation zones around the large second-phase particles acted as sites for particle-stimulated nucleation. In the matrix, at the same time, some elongation of grains occurred. The elongated matrix grains appeared because of the reduction of the dislocation density and the annihilation of some low-angle grain boundaries between chains of subgrains lying in layers parallel to the sheet plane. The matrix processes in this temperatures range can be considered forms of continuous recrystallization. The matrix high-angle grain boundaries started to migrate at the temperature range of the peak 2. They moved mostly in the direction normal to the sheet plane. Heating of the sample for an appropriate time at those temperatures resulted in the complete discontinuous recrystallization of the material. The recrystallized microstructure was dominated now by elongated grains, which were a few times thicker than those obtained by annealing at the temperatures of the peak 1.

Polishing process effect on the image of dispersed precipitates

1984 ◽  
Vol 42 ◽  
pp. 534-535
Author(s):  
C.T. Hu ◽  
C.W. Allen
Keyword(s):  
Matrix Material ◽  
Specimen Preparation ◽  
Second Phase ◽  
Precipitate Particle ◽  
Polishing Process ◽  
Second Phase Particles ◽  
The Matrix ◽  
Surface Profiles ◽  
Thinning Process

One important problem in determination of precipitate particle size is the effect of preferential thinning during TEM specimen preparation. Figure 1a schematically represents the original polydispersed Ni3Al precipitates in the Ni rich matrix. The three possible type surface profiles of TEM specimens, which result after electrolytic thinning process are illustrated in Figure 1b. c. & d. These various surface profiles could be produced by using different polishing electrolytes and conditions (i.e. temperature and electric current). The matrix-preferential-etching process causes the matrix material to be attacked much more rapidly than the second phase particles. Figure 1b indicated the result. The nonpreferential and precipitate-preferential-etching results are shown in Figures 1c and 1d respectively.

Recrystallization in Ultra-Fine Grain Structures of AA3104 Alloy Processed by ECAP and HPT

2012 ◽  
Vol 715-716 ◽  
pp. 346-353
Author(s):  
H. Paul ◽  
T. Baudin ◽  
K. Kudłacz ◽  
A. Morawiec
Keyword(s):  
High Pressure Torsion ◽  
Deformation Mode ◽  
Second Phase ◽  
Orientation Measurement ◽  
Angular Pressing ◽  
Second Phase Particles ◽  
Average Grain Size ◽  
The Matrix ◽  
Electron Microscopes ◽  
Different Strains

The objective of this study was to determine the effect of deformation mode on recrystallization behavior of severely deformed material. Commercial purity AA3104 aluminum alloy was deformed via high pressure torsion and equal channel angular pressing to different strains and then annealed to obtain the state of partial recrystallization. The microstructure and the crystallographic texture were analysed using scanning and transmission electron microscopes equipped with orientation measurement facilities. The nucleation of new grains was observed in bulk recrystallized samples and during in-situ recrystallization in the transmission microscope. Irrespective of the applied deformation mode, a large non-deformable second phase particles strongly influenced strengthening of the matrix through deformation zones around them. It is known that relatively high stored energy stimulates the nucleation of new grains during the recrystalization. In most of the observed cases, the growth of recrystallized grains occurred by the coalescence of neighboring subcells. This process usually led to nearly homogeneous equiaxed grains of similar size. The diameter of grains in the vicinity of large second phase particles was only occasionally significantly larger than the average grain size. Large grains were most often observed in places far from the particles. TEM orientation mapping from highly deformed zones around particles showed that orientations of new grains were not random and only strictly defined groups of orientations were observed.

Microstructure of Friction Stir Processed Mg-Y-Zn Alloy

2007 ◽  
Vol 558-559 ◽  
pp. 777-780 ◽  
Author(s):  
Taiki Morishige ◽  
Masato Tsujikawa ◽  
Sung Wook Chung ◽  
Sachio Oki ◽  
Kenji Higashi
Keyword(s):  
Equal Channel Angular Extrusion ◽  
Second Phase ◽  
Ingot Metallurgy ◽  
Friction Stir ◽  
Fine Grained ◽  
Probe Diameter ◽  
Fine Grain ◽  
Second Phase Particles ◽  
The Matrix ◽  
Zn Alloy

Friction stir processing (FSP) is the effective method of the grain refinement for light metals. The aim of this study is to acquire the fine grained bulk Mg-Y-Zn alloy by ingot metallurgy route much lower in cost. Such bulk alloy can be formed by the superplastic forging. The microstructure of as-cast Mg-Y-Zn alloy was dendrite. The dendrite arm spacing was 72.5 [(m], and there are the lamellar structures in it. FSP was conducted on allover the plate of Mg-Y-Zn alloy for both surfaces by the rotational tool with FSW machine. The stirring passes were shifted half of the probe diameter every execution. The dendrite structures disappeared after FSP, but the lamellar structure could be observed by TEM. The matrix became recrystallized fine grain, and interdendritic second phase particles were dispersed in the grain boundaries. By using FSP, cast Mg-Y-Zn alloy could have fine-grained. This result compared to this material produced by equal channel angular extrusion (ECAE) or rapid-solidified powder metallurgy (RS P/M). As the result, as-FSPed material has the higher hardness than materials produced by the other processes at the similar grain size.

The Room Temperature and Elevated Temperature Fracture Toughness Response of Alloy A-286

1978 ◽  
Vol 100 (2) ◽  
pp. 195-199 ◽  
Author(s):  
W. J. Mills
Keyword(s):  
Fracture Toughness ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Second Phase ◽  
Surface Micromorphology ◽  
Second Phase Particles ◽  
The Matrix ◽  
Temperature Fracture ◽  
Increasing Temperature ◽  
Base Superalloy

The elastic-plastic fracture toughness (JIc) response of precipitation strengthened Alloy A-286 has been evaluated by the multi-specimen R-curve technique at room temperature, 700 K (800°F) and 811 K (1000°F). The fracture toughness of this iron-base superalloy was found to decrease with increasing temperature. This phenomenon was attributed to a reduction in the materials’s strength and ductility at elevated temperatures. Electron fractographic examination revealed that the overall fracture surface micromorphology, a duplex dimple structure coupled with stringer troughs, was independent of test temperature. In addition, the fracture resistance of Alloy A-286 was found to be weakened by the presence of a nonuniform distribution of second phase particles throughout the matrix.

Effect of Heat Treatments on Microstructure and Properties of Hot Compression Aluminum Alloy 7A04

2011 ◽  
Vol 480-481 ◽  
pp. 433-436
Author(s):  
Mu Meng ◽  
Zhi Min Zhang ◽  
Jian Min Yu ◽  
Xin Kai Li
Keyword(s):  
Heat Treatment ◽  
Aluminum Alloy ◽  
Second Phase ◽  
Transgranular Fracture ◽  
High Deformation ◽  
Microstructure And Properties ◽  
T6 Heat Treatment ◽  
Second Phase Particles ◽  
The Matrix ◽  
Fracture Appearance

Aluminum alloy 7A04 compressed at high deformation temperature and large deformation is applied in two different heat treatment (T5 and T6), then microstructure and properties of the alloy after heat treatment are investigated. The mechanical properties are studied by means of the tensile testing and the hardness testing. The microstructure characteristics and the fractorgraphy analysis are respectively investigated with optical microscopy and SEM. The experimental results indicate that after T6 heat treatment, the second-phase particles dispersed in the matrix, which can efficiently improving the strength of the alloy, but reduced the toughness. After T5 heat treatment, the coarse and discontinuous second-phase is distributed along the grain boundary, which can lead to the low strength and high toughness because of the lack of the strengthening phase in the grains. The fracture appearance is intercrystalline fracture after T6 heat treatment, and dimple transgranular fracture after T5 heat treatment.

scholarly journals Unravelling the characteristics of Al-alloy corrosion at the atomic to nanometre scale by transmission electron microscopy

2020 ◽  
Vol 326 ◽  
pp. 01007
Author(s):  
Shravan K. Kairy ◽  
Nick Birbilis
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Al Alloy ◽  
Second Phase ◽  
Clear Understanding ◽  
Transmission Electron ◽  
Second Phase Particles ◽  
Al Matrix

The localised corrosion associated with Mg2Si in the Al-matrix of an Al-Mg-Si alloy was studied in 0.1 M NaCl at pH 6 by quasi in-situ transmission electron microscopy. Herein, physical imaging of corrosion at the atomic to nanometre scale was performed. Phase transformation and subsequent chemical composition variations associated with the localised corrosion of Mg2Si were studied. It was observed that corrosion initiated upon Mg2Si, often preferentially at the interface with the Al-matrix, and propagated until Mg2Si was completely dealloyed by Mg-dissolution, resulting in an amorphous SiO-rich phase remnant. The SiO-rich remnant became electrochemically inert and did not initiate corrosion in the Al-matrix. This study provides a clear understanding on the localised corrosion of Al-alloys associated with Mg2Si. In addition, the methodology followed in this study can also be applied to understand the role of precipitates and second phase particles in the localised corrosion of Al-alloy systems.

x-The Effect of Microstructure on the Corrosion Fatigue Property of A7N01P-T4 Aluminum Alloy Welding Joints

CORROSION ◽  
10.5006/2805 ◽  
2018 ◽  
Vol 74 (11) ◽  
pp. 1229-1236
Author(s):  
Feng Xiao ◽  
Jiangli An ◽  
Hui Chen ◽  
P. Li ◽  
Wei Gao
Keyword(s):  
Grain Boundaries ◽  
Corrosion Fatigue ◽  
Fatigue Property ◽  
Short Crack ◽  
Al Alloy ◽  
Second Phase ◽  
Test Results ◽  
Second Phase Particles ◽  
The Matrix ◽  
Almost All

The corrosion fatigue short crack propagation (CFSCP) behavior of A7N01P-T4 Al alloy welded joints in 3.5 wt% NaCl solution has been investigated. The test results indicate that the CFSCP followed a cyclical type of growth. Microscopic study shows that almost all second-phase particles are distributed along the grain boundary areas. These particles were easily dissolved during the corrosion fatigue test, resulting in weak grain boundaries. Therefore, the fatigue short crack will grow along the winding grain boundaries. While the second-phase particles on the grain boundaries were the main factor to cause the intergranular crack. Transgranular cracking may occur to the coarse grains in the matrix, which indicate that grain size also has a strong influence on the CFSCP behavior of A7N01P-T4 Al alloy.

Mismatch and misorientation at the precipitate/matrix interface in an Al-Zralloy

1983 ◽  
Vol 41 ◽  
pp. 242-243
Author(s):  
Angus Porter ◽  
Louise Makin ◽  
Brian Ralph
Keyword(s):  
High Strength ◽  
Second Phase ◽  
Exact Nature ◽  
Matrix Interface ◽  
Single Image ◽  
Second Phase Particles ◽  
The Matrix ◽  
Lattice Planes ◽  
Zr Alloy ◽  
Zr Alloys

Much of the hardening of high strength aluminium alloys containing zirconium results from the precipitation of the metastable γ' (Al3Zr) phase (Ll2 structure, cube/cube related to the matrix). There exists some controversy in the literature as to the magnitude of the matrix (γ)-γ' misfit in Al-Zr alloys; the values reported range from 1% down to rather less than half this figure. In the present paper, the use of moire fringe imaging to study mismatch and misorientation between the γ and γ' lattice in a binary Al-Zr alloy will be considered. The advantages of this technique for the study of small second-phase particles are three-fold. The information obtained is specific to a single particle; the exact nature of the particle/matrix interface is unimportant, as long as the two lattices exhibit nearly coincident diffraction maxima; and mismatch and misorientation of particular sets of lattice planes can be determined from a single image.

Sign in / Sign up

Export Citation Format

Share Document