Experimental Investigation on the Dynamic Cutting Forces in Internal Broaching

2011 ◽  
Vol 215 ◽  
pp. 234-238 ◽  
Author(s):  
Y.J. Tang ◽  
Yang Yu Wang ◽  
S.M. Ji ◽  
X. Zhang ◽  
Dong Hui Wen
Keyword(s):  
Experimental Investigation ◽  
Cutting Forces ◽  
Strain Sensor ◽  
Test System ◽  
Work Piece ◽  
Test Scheme ◽  
Workpiece Material ◽  
Machined Surface ◽  
Key Characteristics ◽  
Frequency Domains

Cutting forces generated in broaching have a direct influence on the generation of heat, tool wear or failure, quality of machined surface and accuracy of the work piece. In this paper not only a cutting forces test scheme has been proposed but also a cutting forces measurement equipment has been designed with PCB 740B02 dynamical strain sensor and LMS SCADA III test system, respectively. Dynamical strain sensor was pasted on the cylinder type sensitive elements with which table and workpiece was connected. Experimental investigation on the dynamic cutting forces in the broaching direction of a hydraulic broaching machine had been carried out. Cutting forces measurement tests on Q235 steel workpiece material during broaching had been performed. Broaching in a variety of velocities, namely, 3.3m/min, 5m/min and 8m/min and in a variety of cutting depth, namely, 0.03mm, 0.04mm, 0.05mm and 0.07mm, were investigated. Output signal was analyzed both in time and frequency domains and the key characteristics of the cutting forces signal was obtained. Correlation between the frequency of broaching forces and the broaching velocity was also studied.

scholarly journals Design and Development of a Three Component Milling Dynamometer

2021 ◽  
Vol 2070 (1) ◽  
pp. 012168
Author(s):  
Narender Maddela ◽  
Ch.Sai Kiran ◽  
Aluri Manoj ◽  
M. Kapila ◽  
B. Swapna ◽  
...  
Keyword(s):  
Tool Wear ◽  
Heat Generation ◽  
Strain Gauge ◽  
Cutting Forces ◽  
Metal Cutting ◽  
Strain Gauges ◽  
Tool Geometry ◽  
Work Piece ◽  
Design And Development ◽  
Machined Surface

Abstract The cutting forces that are generated during metal cutting influence the work piece precision, tool wear, the nature of the machined surface, and heat generation. These cutting forces can be measured analytically however; precise outcomes may not be expected due to its included stresses, parameters of cutting, and the perplexing tool geometry. Henceforth the exploratory estimation of cutting forces is fundamental. For this reason, a milling dynamometer of three-segment is structured, created, and tried to gauge the three cutting forces which are produced during the operation of milling strain gauges can be utilized to quantify dynamic and static cutting forces through milling dynamometer. During the process of metal cutting, a dynamometer that is based on strain gauge is fit for estimating three-force segments. The dynamometer was designed based on the octagonal ring principle. The octagonal rings orientation and location of strain gauges have resolved to expand affectability and to limit cross-affectability.

The Experimental Investigation of the Effects of Different Chip Breaker Forms on the Cutting Forces

2007 ◽  
Vol 23 ◽  
pp. 191-194 ◽  
Author(s):  
Huseyin Gürbüz ◽  
Adem Kurt ◽  
I. Korkut ◽  
Ulvi Şeker
Keyword(s):  
Experimental Investigation ◽  
Cutting Forces ◽  
Manufacturing Industry ◽  
Cutting Parameters ◽  
Cutting Conditions ◽  
Depth Of Cut ◽  
Test Results ◽  
Workpiece Material ◽  
Chip Breaker ◽  
Cutting Speeds

The objective of this paper is experimentally investigation of the effects of different chip breaker forms on the cutting forces according to various cutting parameters. AISI 1050 workpiece material, most used material in the manufacturing industry, and SNMG 120408R inserts and PSBNR 2525M12 tool holder have 75° approaching angle according to ISO 3685 are used in the experiments. Seven groups chip breaker form were used in the tests. The chip breaker forms are the coated inserts MA, SA, MS, GH and standard, and the uncoated inserts MS and standard. These inserts are Mitsubishi UC 6010 and UTI20T grade; correspond to ISO P30 and P15 grade, respectively. Machining tests were carried out by using five levels of cutting speeds (150, 200, 250, 300, 350 m/min), three levels of feed rate (0.15, 0.25, 0.35 mm/rev) and two levels of depth of cut (1.6, 2.5 mm). Cutting forces were measured using Kistler dynamometer. The test results show that the highest cutting force values were measured on SA, GH, MA forms, respectively. Complex chip breaker forms cause the increase of the cutting forces. Although the cutting forces on the uncoated inserts were partly small in light cutting conditions, it has increased on the uncoated inserts in heavy cutting conditions compared to coated inserts.

Analysis of Cutting Forces and Machining Error in Ball End Milling of Cylindrical Surfaces

2011 ◽  
Vol 328-330 ◽  
pp. 560-564
Author(s):  
Ba Sheng Ouyang ◽  
Guo Xiang Lin ◽  
Yong Hui Tang
Keyword(s):  
Cutting Forces ◽  
End Milling ◽  
Cutting Conditions ◽  
Machining Error ◽  
Machined Surface ◽  
Convex Surfaces ◽  
Machining Errors ◽  
End Mills ◽  
Tool Deflections ◽  
Cutting Modes

Cutting forces and machining error in contouring of concave and convex surfaces using helical ball end mills are theoretically investigated. The cutting forces are evaluated based on the theory of oblique cutting. The machining errors resulting from the tool deflections due to these forces are evaluated at various points of the machined surface. The influence of various cutting conditions and cutting modes on machining error is investigated and discussed.

Prediction of Cutting Forces in Milling Stainless Steels using Chamfered Main Cutting Edge Tool

2005 ◽  
Vol 21 (3) ◽  
pp. 145-155 ◽  
Author(s):  
C.-S. Chang
Keyword(s):  
Stainless Steel ◽  
Cutting Forces ◽  
Steel Plate ◽  
Cutting Edge ◽  
304 Stainless Steel ◽  
Workpiece Material ◽  
Material Force ◽  
Force Data ◽  
Edge Tool ◽  
Good Agreement

AbstractTo study the cutting forces, the carbide tip's surface temperature, and the mechanism of secondary chip and main chip formation of face milling stainless steel with a chamfered main cutting edge has been investigated. Theoretical values of cutting forces were calculated and compared to the experimental results with SUS 304 stainless steel plate as a workpiece material. Force data from these tests were used to estimate the empirical constants of the mechanical model and to verify its prediction capabilities. A comparison of the predicted and measured forces shows good agreement. A preliminary discussion is also made for the design of special tool holders and their geometrical configurations. Next, the tips mounted in the tool holders are ground to a chamfered width and the tool dimensions are measured by using a toolmaker microscope.

scholarly journals Analysis of Forces in Vibro-Impact and Hot Vibro-Impact Turning of Advanced Alloys

2011 ◽  
Vol 70 ◽  
pp. 315-320 ◽  
Author(s):  
Riaz Muhammad ◽  
Agostino Maurotto ◽  
Anish Roy ◽  
Vadim V. Silberschmidt
Keyword(s):  
Finite Element ◽  
Cutting Forces ◽  
Three Dimensional ◽  
Element Model ◽  
Machining Process ◽  
Strain Rates ◽  
Machining Processes ◽  
Machined Surface ◽  
Cutting Zone

Analysis of the cutting process in machining of advanced alloys, which are typically difficult-to-machine materials, is a challenge that needs to be addressed. In a machining operation, cutting forces causes severe deformations in the proximity of the cutting edge, producing high stresses, strain, strain-rates and temperatures in the workpiece that ultimately affect the quality of the machined surface. In the present work, cutting forces generated in a vibro-impact and hot vibro-impact machining process of Ti-based alloy, using an in-house Ultrasonically Assisted Turning (UAT) setup, are studied. A three-dimensional, thermo-mechanically coupled, finite element model was developed to study the thermal and mechanical processes in the cutting zone for the various machining processes. Several advantages of ultrasonically assisted turning and hot ultrasonically assisted turning are demonstrated when compared to conventional turning.

scholarly journals Technological Features in Processing of Conical Lenses

2020 ◽  
Vol 19 (6) ◽  
pp. 521-527
Author(s):  
M. I. Filonova ◽  
R. O. Dias Gonzalez ◽  
A. A. Sukhotzkiy ◽  
A. S. Kozeruk ◽  
A. V. Semchuonok
Keyword(s):  
Glass Plate ◽  
Experimental Studies ◽  
Central Zone ◽  
Conical Surface ◽  
Work Piece ◽  
Cylindrical Shape ◽  
Cylindrical Blank ◽  
Machined Surface ◽  
Optimal Sequence ◽  
Plane Parallel

The paper presents the technology of obtaining flat-conical lenses (axicons) by the method of free grinding a work-piece to a flat tool through a layer of abrasive suspension. For this, theoretical and experimental studies of the regularities of stock removal from the base of the cone and its lateral surface have been carried out. The processing modes have been identified that ensure both uniform operation of the flat surface of  the part and enhanced removal of  the allowance in the edge or central zone of this surface. During the study of the processing of the conical surface, the set-up parameters of the technological equipment have been established, at which there is a minimum deviation of the generatrix of the cone from straightness and maximum productivity of the process. The stages of processing conical lenses are proposed, which allow to assign the optimal sequence of operations in the manufacture of this type of parts from blanks of a cylindrical shape in cases where  the ratio of the height of the cone to the diameter of its base H/d £ 0.5. The main stages of processing include: grinding of the bases of cylindrical blanks with maintaining their mutual parallelism with a given accuracy; polishing one of the cylinder bases to achieve the required roughness and deviation from non-flatness; fastening a cylindrical blank to an auxiliary plane-parallel glass plate using molecular cohesion forces; mechanical fastening of a cylindrical work-piece with a collet adapter mandrel for a plane-parallel glass plate; applying the nearest sphere to the second base of the cylindrical blank; drawing a conical surface on the spherical part of a plano-convex lens; grinding and polishing the conical surface to achieve the required roughness  and straightness of the cone generatrix. The degree of efficiency of the setup parameters of the machine has been revealed depending on the technological heredity of the work-piece from the point of view of the distribution of the allowance to be removed over the machined surface. 

Sign in / Sign up

Export Citation Format

Share Document