Effect of Heat Treatment on Microstructure and Mechanical Properties of a Ti-Mo-Zr Alloy

2011 ◽  
Vol 275 ◽  
pp. 155-158
Author(s):  
X.N. Zhang ◽  
Peng Cao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Young’S Modulus ◽  
Design Theory ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Ingot Metallurgy ◽  
Orthopaedic Implant ◽  
Microstructure And Mechanical Properties ◽  
Zr Alloy

Recently there is increasing demand for the development of new -type titanium with a low elastic modulus for surgical orthopaedic implant applications. In this paper, we developed a new Ti-Mo-Zr alloy based on the d-electron alloy design theory. The designed Ti-12Mo-5Zr (at%) alloy was then produced using ingot metallurgy and evaluated pertaining to the effect of heat treatment on the microstructure and mechanical properties. The alloy exhibited a relatively low Young’s modulus similar to some typical  orthopaedic titanium alloys. Yield strength, tensile strength and Young’s modulus of the alloy decreased after solid solution treatment. The mechanism by which heat treatment affects the mechanical properties is discussed.

scholarly journals Evolution of Microstructure and Mechanical Properties of Nanostructured NiFe Films under Influence of Heat Treatment

2021 ◽  
Vol 20 (2) ◽  
pp. 109-120
Author(s):  
V. M. Fedosyuk
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Surface Layer ◽  
Young’S Modulus ◽  
Heat Treatment Temperature ◽  
Young's Modulus ◽  
Treatment Temperature ◽  
Microstructure And Mechanical Properties ◽  
Internal Volume

. Nanostructured NiFe films were synthesized by pulsed electrolytic deposition on silicon with a gold sublayer, after which they have been subjected to to temperature treatment at 373-673 K in order to study the effect of heat treatment on the microstructure and mechanical properties of the objects under study. High-resolution atomic force microscopy has made it possible  to trace the stages of  microstructure evolution under the  influence of  heat treatment, including the process of  nonlinear increase in grain growth and two-stage agglomeration. It is shown that with an increase in heat treatment temperature to 673 K, the grain size increases from 68 to 580 nm in comparison with the initial sample, undergoing agglomeration processes at temperatures of  100 and 300 °C. The mechanical properties of nanostructured NiFe films have been studied by the nanoindentation method. The dependences of the hardness of Young’s modulus and the values of the resistance to elastoplastic deformation on depth have been obtained and analyzed in the paper. This approach has permitted to reveal differences in the behavior of the mechanical properties of the surface layer and the internal volume of the film under the action of different heat treatment temperatures, as well as to demonstrate the opposite reaction of different material layers to an increase in temperature. As a result of a thorough analysis of the deformation curves of nanoindentation, it has been found that the homogenization of the surface in combination with the activation of oxidation processes leads to the strengthening of near-surface layer of NiFe films. At the same time, the internal volume of the material is characterized by a nonlinear decrease in hardness and Young’s modulus with an increase in the heat treatment temperature. The explanation for this phenomenon has been found in the complex effect of a decrease in the number of grain boundaries (due to an increase in the average grain size with increasing temperature) and an increase in the concentration of gold atoms diffusing from the sublayer more actively with an increase in the processing temperature of NiFe films.

scholarly journals Tailoring a Low Young Modulus for a Beta Titanium Alloy by Combining Severe Plastic Deformation with Solution Treatment

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3467
Author(s):  
Anna Nocivin ◽  
Doina Raducanu ◽  
Bogdan Vasile ◽  
Corneliu Trisca-Rusu ◽  
Elisabeta Mirela Cojocaru ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
Young Modulus ◽  
Orthopedic Implants ◽  
Beta Titanium Alloy

The present paper analyzed the microstructural characteristics and the mechanical properties of a Ti–Nb–Zr–Fe–O alloy of β-Ti type obtained by combining severe plastic deformation (SPD), for which the total reduction was of etot = 90%, with two variants of super-transus solution treatment (ST). The objective was to obtain a low Young’s modulus with sufficient high strength in purpose to use the alloy as a biomaterial for orthopedic implants. The microstructure analysis was conducted through X-ray diffraction (XRD), scanning electron microscopy (SEM), and high-resolution transmission electron microscopy (HRTEM) investigations. The analyzed mechanical properties reveal promising values for yield strength (YS) and ultimate tensile strength (UTS) of about 770 and 1100 MPa, respectively, with a low value of Young’s modulus of about 48–49 GPa. The conclusion is that satisfactory mechanical properties for this type of alloy can be obtained if considering a proper combination of SPD + ST parameters and a suitable content of β-stabilizing alloying elements, especially the Zr/Nb ratio.

Mechanical Properties of Pyrolytic "SiOCN" Thin Coatings

1993 ◽  
Vol 308 ◽  
Author(s):  
Sandrine Bec ◽  
André Tonck ◽  
Jean-Luc Loubet
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Ceramic Coatings ◽  
Optical Observation ◽  
Thin Coatings ◽  
Polymer Precursors ◽  
Polymeric State

ABSTRACTPyrolysis of polymer precursors (polysilazane) is a technologically and economically interesting way to produce thin ceramic coatings. However, many cracks appear and decohesion occurs during pyrolysis when the ceramic coatings (SiOCN) are thicker than 0.5 micrometers. In order to understand these cracking phenomena, the coatings are mechanically characterized by nanoindentation at different stages of the pyrolysis heat treatment.During pyrolysis, the cracking temperature is detected by in-situ optical observation. The thickness of the coatings varies during pyrolysis from 3 micrometers at the polymeric state to 1 micrometer at the ceramic state. The coatings' properties, hardness and Young's modulus are evaluated after heat treatment, taking into account the substrate's influence. A large variation of these properties occurs at the cracking temperature. Both the hardness and the Young's modulus are multiplied by a factor of 10. By analysing these results, we show that cracking is correlated with the evolution of the coatings' mechanical properties during the transformation.

scholarly journals Effects of Gd, Y Content on the Microstructure and Mechanical Properties of Mg-Gd-Y-Nd-Zr Alloy

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 790 ◽  
Author(s):  
Changping Tang ◽  
Kai Wu ◽  
Wenhui Liu ◽  
Di Feng ◽  
Xuezhao Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Solution Treatment ◽  
Age Hardening ◽  
Uniaxial Tensile ◽  
Microstructure And Mechanical Properties ◽  
Shaped Particle ◽  
Zr Alloy ◽  
Non Equilibrium

The effects of Gd, Y content on the microstructure and mechanical properties of Mg-Gd-Y-Nd-Zr alloy were investigated using hardness measurements, X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), and uniaxial tensile testing. The results indicate that the alloys in as-cast condition mainly consist of α-Mg matrix and non-equilibrium eutectic Mg5.05RE (RE = Gd, Y, Nd). After solution treatment, the non-equilibrium eutectics dissolved into the matrix but some block shaped RE-rich particles were left at the grain boundaries and within grains. These particles are especially Y-rich and deteriorate the mechanical properties of the alloys. Both the compositions of the eutectic and the block shaped particle were independent of the total Gd, Y content of the alloys, but the number of the particles increases as the total Gd, Y content increases. The ultimate tensile strength increases as the total Gd, Y content decreases. A Mg-5.56Gd-3.38Y-1.11Nd-0.48Zr alloy with the highest ultimate tensile strength of 280 MPa and an elongation of 1.3% was fabricated. The high strength is attributed to the age hardening behavior and the decrease in block shaped particles.

Phase Stability and Mechanical Properties of Ti-Cr-Sn-Zr Alloys Containing a Large Amount of Zr

2016 ◽  
Vol 879 ◽  
pp. 1344-1349 ◽  
Author(s):  
Yonosuke Murayama ◽  
Erdnechuluun Enkhjavkhlan ◽  
Akihiko Chiba
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Deformation Behavior ◽  
Single Phase ◽  
Young's Modulus ◽  
Martensitic Structure ◽  
Β Phase ◽  
Microstructural Transition ◽  
Zr Alloy ◽  
Zr Alloys

The Young’s modulus of Ti-Cr-Sn-Zr alloy varies with the composition of Cr, Sn and Zr, in which the elements act as β stabilizers. Some Ti-Cr-Sn-Zr alloys show very low Young’s modulus under 50GPa. The amount of Zr in alloys with very low Young's modulus increases with the decrease of Cr. We investigated the Young’s modulus and deformation behavior of Ti-xCr-Sn-Zr (x=0~1mass%) alloys containing a large amount of Zr. The quenched microstructure of Ti-Cr-Sn-Zr alloys changes from martensitic structure to β single-phase structure if the amounts of β stabilized elements are increased. The Ti-Cr-Sn-Zr alloys with compositions close to the transitional composition of microstructure from martensite to β phase show minimum Young’s modulus. The clear microstructural transition disappears and the minimum Young’s modulus increases if the amount of Cr becomes too small. In Ti-Cr-Sn-Zr alloys containing a large amount of Zr, Young’s modulus depends on β phase that is intermingled with martensite.

Mechanical Properties of Ti-Cr-Sn-Zr Alloys

2010 ◽  
Vol 638-642 ◽  
pp. 635-640 ◽  
Author(s):  
Yonosuke Murayama ◽  
Shuichi Sasaki ◽  
Hisamichi Kimura ◽  
Akihiko Chiba
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Biomedical Application ◽  
Young's Modulus ◽  
Mechanical Twinning ◽  
Β Phase ◽  
Low Modulus ◽  
Deformation Modes ◽  
Zr Alloy ◽  
Zr Alloys

Low modulus β Ti alloys are attractive for biomedical application. This work examines the mechanical properties of Ti-Cr-Sn-Zr system alloys, especially the effect of the varying alloy composition on the microstructure, the Young’s modulus and the deformation mechanism.The Young’s modulus of the alloy varies with the composition, which variation is caused mainly from the competition between the meta-stable β phase and ω phase.The deformation modes of the Ti-Cr-Sn-Zr alloy, which are the mechanical twinning, the deformation by slip and the deformation-induced transformation, also change depending on the composition of the alloy. The minimum of the Young’s modulusof the Ti-Cr-Sn-Zr alloy in this experiment was shown in the composition where the microstructure of the alloy changes from the martensitic structure to the meta-stable β structure.

Effect of Heat Treatment on Microstructure and Mechanical Properties in ZK60 Alloy Sheet

2007 ◽  
Vol 567-568 ◽  
pp. 361-364 ◽  
Author(s):  
Suk Bong Kang ◽  
Jae Hyung Cho ◽  
Hyoung Wook Kim ◽  
Y.M Jin
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solution Treatment ◽  
Aging Treatment ◽  
Growth Direction ◽  
Warm Rolling ◽  
Alloy Sheet ◽  
Microstructure And Mechanical Properties ◽  
Zk60 Alloy ◽  
Hardness Values

The sheet of ZK60 alloy with a thickness of 1mm was prepared from a casting ingot followed by homogenization and warm-rolling. Variations in microstructure and mechanical properties of ZK60 alloy sheets were investigated during T6 treatment. Especially artificial aging after solution heat treatment affected both precipitates distribution and mechanical properties with aging treatment. Variations of mechanical properties were related to precipitates, i.e. rod-shaped ( 1 β ′ ) or disc shaped ( 2 β ′ ) particles. Around the peak of hardness values, regularly distributed rod-shaped ( 1 β ′ ) precipitates were found. The rod-shaped ( 1 β ′ ) precipitates were oriented with a growth direction of [0001]. When over-aged, rod-shaped ( 1 β ′ ) precipitates were expected to decrease and the density of disc-shaped ( 2 β ′ ) precipitates to change. The rod-shaped ( 1 β ′ ) precipitates mainly consist of {Mg, Zn}, while disc-shaped ( 2 β ′ ) precipitates, {Mg, Zn, Zr} or {Mg, Zn}. In this study the optimum T6 treatment was determined as solution treatment at 430 °C for 6 hours and subsequently aging treatment at 175 °C for 18 hours. At this T6 condition the tensile strength, yield strength and elongation are 321MPa, 280MPa and 16%, respectively.

Microstructure and Mechanical Properties of Porous Titanium Based on Controlling Young's Modulus

2017 ◽  
Vol 46 (8) ◽  
pp. 2041-2048 ◽  
Author(s):  
Xu Guangsheng ◽  
Kou Hongchao ◽  
Liu Xianghong ◽  
Li Fuping ◽  
Li Jinshan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Porous Titanium ◽  
Microstructure And Mechanical Properties

Development of Biomedical Near β Titanium Alloys

2009 ◽  
Vol 618-619 ◽  
pp. 303-306 ◽  
Author(s):  
Zhen Tao Yu ◽  
Gui Wang ◽  
Xi Qun Ma ◽  
Matthew S. Dargusch ◽  
Jian Ye Han ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Titanium Alloys ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Solution Treatment ◽  
High Strength ◽  
Alloy Chemistry ◽  
Solution Treated ◽  
Strength And Plasticity ◽  
Hot Rolled

The effects of alloy chemistry and heat treatment on the microstructure and mechanical properties of Ti-Nb-Zr-Mo-Sn near  type titanium alloys have been investigated. Near β titanium alloys consisting of non-toxic alloying elements Mo, Nb, Zr, Sn possess a low Young’s modulus, and moderate strength and plasticity. As the hot rolled TLM alloy (Ti-25Nb-3Zr-3Mo-2Sn) possesses high strength and low Young’s modulus a detailed investigation is performed for this alloy. Solution treatment of the hot rolled TLM alloy reduces strength and increases ductility without affecting the Young’s modulus. Ageing of the solution treated TLM alloy reduces elongation and increases the Young’s modulus with little change in strength. Both solution treated and aged conditions show features of two stage yielding associated with a strain induced martensitic transformation.

Sign in / Sign up

Export Citation Format

Share Document