Synthesis of PEG200 Lauric Acid Diester and the Performance Test of Viscosity

2011 ◽  
Vol 301-303 ◽  
pp. 3-8
Author(s):  
Tong Yu Chen ◽  
Yan Jun Liu ◽  
Guo Zheng ◽  
Yu Sun
Keyword(s):  
Polyethylene Glycol ◽  
Reaction Time ◽  
Reaction Temperature ◽  
Lauric Acid ◽  
Reverse Micelles ◽  
Performance Test ◽  
Characteristic Curve ◽  
Molar Ratio ◽  
High Yield ◽  
Infrared Spectrometer

A novel PEG200 lauric acid diester was synthesized high yield by direct esterification using polyethylene glycol and lauric acid respectively was presented in this work. The product of PEG200 lauric acid diester was characterized by a fourier transform infrared spectrometer(FTIR). The effects of catalyst, reaction time, reaction temperature and molar ratio on the reaction were discussed. The optimum synthetic condition of PEG200 lauric acid diester: esynthesis is based on protection of N2and the ressure is 0.08Mpa. Using mass fraction 0.45% in p-toluene sulphonic acid as catalyst, molar ratio of polyethylene glycol and oleic acid 1:1.95, reaction temperature about 130-140°C, and reaction time 9-10h. The results of testing of diester products showed that the yield of PEG200 lauric acid diester is 98.2%.And this article reviewed the effect of concentration on viscosity. The characteristic curve of Viscosity-Concentration showed the viscosity increased with increase of the concentration which brought about the increase of particle size. Especially focusing on the maximum viscosity appeard on 80% because of the phenomenon of reverse micelles. Then the viscosity decreased with increase of the concentration.

scholarly journals Comparison of homogeneous and heterogeneous catalysis for synthesis of biodiesel from M. indica oil

2011 ◽  
Vol 17 (2) ◽  
pp. 117-124 ◽  
Author(s):  
B. Singh ◽  
Faizal Bux ◽  
Y.C. Sharma
Keyword(s):  
Reaction Time ◽  
Heterogeneous Catalysis ◽  
Heterogeneous Catalyst ◽  
Reaction Temperature ◽  
Molar Ratio ◽  
High Yield ◽  
Homogeneous Catalyst ◽  
Catalyst Amount ◽  
Optimum Yield

Biodiesel was developed by transesterification of Madhuca indica oil by homogeneous and heterogeneous catalysis. KOH and CaO were taken as homogeneous and heterogeneous catalyst respectively. It was found that the homogeneous catalyst (KOH) took 1.0 h of reaction time, 6:1 methanol to oil molar ratio, 0.75 wt% of catalyst amount, 55?0.5?C reaction temperature for completion of the reaction. The heterogeneous catalyst (CaO) was found to give optimum yield in 2.5 h of reaction time at 8:1 methanol to oil molar ratio, 2.5 wt% of catalyst amount, at 65?0.5?C. A high yield (95-97%) and conversion (>96.5%) was obtained from both the catalysts. CaO was found to leach to some extent in the reactants and a biodiesel conversion of 27-28% was observed as a result of leaching.

Synthesis and Optimization of Methyl Laurate Using Sulfonated Pyrrolidonium Ionic Liquid as a Catalyst

2018 ◽  
Vol 17 (3) ◽  
Author(s):  
Benyong Han ◽  
Fang Yin ◽  
Shiqing Liu ◽  
Xingling Zhao ◽  
Jing Liu ◽  
...  
Keyword(s):  
Ionic Liquid ◽  
Reaction Time ◽  
Reaction Temperature ◽  
Lauric Acid ◽  
Methyl Laurate ◽  
Molar Ratio ◽  
Esterification Reaction ◽  
Hydrogen Sulfate ◽  
Single Factor ◽  
Central Composite

Abstract Methyl laurate was synthesized from lauric acid and methanol using Brønsted acid ionic liquids as catalysts, by an esterification reaction. The efficiencies of four different catalysts, 1-methylimidazolium hydrogen sulfate ([Hmim]HSO4), 2-pyrrolidonium hydrogen sulfate ([Hnhp]HSO4), 1-(3-sulfonic acid) propyl-2-pyrrolidonium hydrogen sulfate ([C3SO3Hnhp]HSO4) and H2SO4 were compared. The effect of the methanol/lauric acid molar ratio, reaction temperature, reaction time, and catalyst dosage on the lauric acid conversion was investigated by single-factor experiments. On the basis of single-factor experiments, the esterification of lauric acid and methanol was optimized using response surface methodology (RSM) based on central composite design (CCD). The results showed that the most effective catalyst was the ionic liquid [C3SO3Hnhp]HSO4. The optimal conditions were as follows: [C3SO3Hnhp]HSO4 dosage of 10 % (based on the mass of lauric acid), methanol/lauric acid molar ratio of 9:1, reaction time of 1 h and reaction temperature of 70 °C. Under these conditions, the lauric acid conversion reached 95.33 %. The catalytic activity of [C3SO3Hnhp]HSO4 still remained high after 5 cycles.

Biodiesel Synthesis from Styrax Tonkinensis Catalyzed by S2O82-/ZrO2-TiO2-Fe3O4

2014 ◽  
Vol 521 ◽  
pp. 621-625 ◽  
Author(s):  
Yi Gang Wang ◽  
Xiao An Nie ◽  
Zhen Xing Liu
Keyword(s):  
Reaction Time ◽  
Reaction Temperature ◽  
Recovery Rate ◽  
Catalytic Effect ◽  
Solid Acid ◽  
Catalytic Efficiency ◽  
Molar Ratio ◽  
High Yield ◽  
Catalyst Amount ◽  
Biodiesel Synthesis

The preparation of biodiesel from Styrax Tonkinensis catalyzed by solid acid S2O82-/ZrO2-TiO2-Fe3O4 at an autoclave was studied in this paper. The magnetic catalysts were characterized by XRD, which explained the high catalytic effect. At the same time, the recovery rate and usage count of catalysts were also studied. And the results showed that a high yield of transesterification can be obtained in a closed autoclave at the condition of catalyst amount 5 %, reaction time 1.5 h, reaction temperature 373K and methanol and oil molar ratio 10:1. The results also showed that the catalysts were still with a higher catalytic efficiency when the catalysts were calcinated after the forth usage.

scholarly journals Optimization of Enzymatic Synthesis of Betulinic Acid Amide in Organic Solvent by Response Surface Methodology (RSM)

2019 ◽  
Vol 19 (4) ◽  
pp. 849
Author(s):  
Nurul Atikah Amin Yusof ◽  
Nursyamsyila Mat Hadzir ◽  
Siti Efliza Ashari ◽  
Nor Suhaila Mohamad Hanapi ◽  
Rossuriati Dol Hamid
Keyword(s):  
Response Surface Methodology ◽  
Reaction Time ◽  
Response Surface ◽  
Reaction Temperature ◽  
Betulinic Acid ◽  
Enzymatic Synthesis ◽  
Acid Amide ◽  
Molar Ratio ◽  
Percentage Yield ◽  
Substrate Molar Ratio

Optimization of the lipase catalyzed enzymatic synthesis of betulinic acid amide in the presence of immobilized lipase, Novozym 435 from Candida antartica as a biocatalyst was studied. Response surface methodology (RSM) and 5-level-4-factor central-composite rotatable design (CCRD) were employed to evaluate the effects of the synthesis parameters, such as reaction time (20–36 h), reaction temperature (37–45 °C), substrate molar ratio of betulinic acid to butylamine (1:1–1:3), and enzyme amounts (80–120 mg) on the percentage yield of betulinic acid amide by direct amidation reaction. The optimum conditions for synthesis were: reaction time of 28 h 33 min, reaction temperature of 42.92 °C, substrate molar ratio of 1:2.21, and enzyme amount of 97.77 mg. The percentage yield of actual experimental values obtained 65.09% which compared well with the maximum predicted value of 67.23%. The obtained amide was characterized by GC, GCMS and 13C NMR. Betulinic acid amide (BAA) showed a better cytotoxicity compared to betulinic acid as the concentration inhibited 50% of the cell growth (IC50) against MDA-MB-231 cell line (IC50 < 30 µg/mL).

Synthesis of light-colored rosin glycerol ester

Holzforschung ◽  
2007 ◽  
Vol 61 (5) ◽  
pp. 499-503 ◽  
Author(s):  
Shifa Wang
Keyword(s):  
Reaction Time ◽  
Reaction Temperature ◽  
Softening Point ◽  
Acid Number ◽  
Total Weight ◽  
Molar Ratio ◽  
Optimal Dosage ◽  
Weight Percentage ◽  
Glycerol Ester ◽  
Ring Method

Abstract A light-colored rosin glycerol ester was synthesized from gum rosin and glycerol in the presence of a highly effective decolorizing agent. The effects of the type and dosage of the decolorizing agent and the reaction temperature and time on the yield, softening point, color, and acid number of the rosin glycerol ester were investigated. Experimental results showed that 4,4′-thio-bis(6-tert-butyl-3-methyl phenol) was the best decolorizing agent. It promoted esterification at an optimal dosage of 0.5% (based on the weight percentage of starting material rosin). Suitable conditions for esterification of rosin and glycerol were: reaction temperature, 260–270°C; reaction time, 6–8 h; and rosin/glycerol molar ratio, 2.5:1 (mol mol-1). The characteristics of the rosin glycerol ester obtained under these conditions were as follows: softening point, 90–94°C (ball and ring method); color, 1–2 (Gardner value); acid number, 7–8; and yield, >88% (based on the total weight of rosin and glycerol). The selected additive has a multifunctional effect involving bleaching, disproportionation, and catalysis.

Synthesis and Characterization of a New Phosphorus-Containing Curing Agent PPDTA

2019 ◽  
Vol 953 ◽  
pp. 185-190
Author(s):  
Yong Li Peng ◽  
Ni An Zhuo ◽  
Can Zhang
Keyword(s):  
Infrared Spectroscopy ◽  
Reaction Time ◽  
Reaction Temperature ◽  
Orthogonal Experiment ◽  
Molar Ratio ◽  
Synthesis And Characterization ◽  
Curing Agent ◽  
Phosphorus Containing ◽  
Three Factor

A new phosphorus-containing flame-retardant curing agent PPDTA was synthesized from phenylphosphonic dichloride (PPD) and 3-amino-1,2,4-triazole (TA) in tetrahydrofuran solvent to improve the flame retardancy of epoxy resin. The structure of the compound was analyzed and confirmed by infrared spectroscopy. The effects of reaction time, reaction temperature and ratio of reactants on yield were studied by using three-factor three-level orthogonal experiment. The results show that the yield of PPDTA can reach 86.4%, when the reaction time is 10h, reaction temperature is 70 °Cand the molar ratio of TA to PPD is 2.2:1.

Preparation and Characterization of Cationic Cassia Tora Gum

2013 ◽  
Vol 781-784 ◽  
pp. 526-530 ◽  
Author(s):  
Shao Ying Li ◽  
Chun Mei Niu ◽  
Hua Yu Zhong
Keyword(s):  
Reaction Time ◽  
Reaction Temperature ◽  
Water Solubility ◽  
Cold Water ◽  
Water Solution ◽  
Molar Ratio ◽  
Reaction Conditions ◽  
Cassia Tora ◽  
Dispersing Agent

Series of cationic cassia tora gum (CCTG) were synthesized using 3-chloro-2-hydroxypropyl trimethyl ammonium chloride (CHPTAC) as cationic etherifying agent, isopropanol-water solution as dispersing agent, in presence of sodium hydroxide under different reaction conditions. The optimum ratio for preparing the cationic cassia tora gum are that CHPTAC-CTG molar ratio is 0.6:1; NaOH-CHPTAC molar ratio is 1.3:1.The optimum conditions are that reaction temperature is 55°Cand reaction time is 3.5 h. The cold water solubility was improved apparently. The solution transmittance has corresponding relationship with the nitrogen content (N%) in the certain range, and the maximum transmittance is up to 87.2%. N% increased with the increase of reaction time and stable N% can be obtained in shorter reaction time at higher reaction temperature. The products were characterized by 13C-NMR. The heat resistance of CTG and CCTG were analyzed.

scholarly journals Synthesis and Performance ofN-(Benzoyl) Stearic Acid Hydrazide

2012 ◽  
Vol 9 (2) ◽  
pp. 545-552 ◽  
Author(s):  
Yan-Hua Cai ◽  
Shun-Jiang Li
Keyword(s):  
Reaction Time ◽  
Stearic Acid ◽  
Reaction Temperature ◽  
Orthogonal Experiment ◽  
Acid Hydrazide ◽  
Semiempirical Method ◽  
Molar Ratio ◽  
H Nmr ◽  
And Performance ◽  
Benzoyl Hydrazine

N-(benzoyl) stearic acid hydrazide was synthesized from benzoyl hydrazine and stearyl chloride which was deprived from stearic acid via acylation. The structure of the compound had been characterized by FT-IR,1H NMR, at the same time, the structure of N-(benzoyl) stearic acid hydrazide was optimized by the semiempirical method PM3. The influence of the reaction ratio, reaction time and reaction temperature to the yield ofN-(benzoyl) stearic acid hydrazide was investigated by orthogonal experiment, and the optimized reaction condition was molar ratio of benzoyl hydrazine: stearyl chloride 1:1, reaction time 6 h, reaction temperature 70°C, and the yield was 92.9%. The TGA thermal analysis of N-(benzoyl) stearic acid hydrazide showed that thermal stability ofN-(benzoyl) stearic acid hydrazide was affected by heating rate, and theN-(benzoyl) stearic acid hydrazide enhanced the tensile strength, modulus and elongation at break of Poly(L-lactic acid)(PLLA).

Catalytic Synthesis of Ethyl Acetate Using Ti2SnC

2013 ◽  
Vol 634-638 ◽  
pp. 628-631
Author(s):  
Yun Hui Long ◽  
Jun Ming Guo ◽  
Du Shu Huang ◽  
Gui Yang Liu
Keyword(s):  
Acetic Acid ◽  
Reaction Time ◽  
Ethyl Acetate ◽  
Reaction Temperature ◽  
Conversion Rate ◽  
Reaction System ◽  
Catalytic Performance ◽  
Catalytic Synthesis ◽  
Molar Ratio ◽  
The Ideal

The catalytic synthesis of ethyl acetate from ethanol and acetic acid using Ti2SnC in liquid phase under the atmospheric pressure was studied. The influences of some factors such as catalyst usage, initial reactant molar ratio, reaction temperature and reaction time on acetic acid conversion rate of this reaction system were investigated. The acetic acid conversion rate of 88.12% is achieved while the molar ratio of alcohol and acid is 1:3.6, the amount of catalyst is 0.2000 g, the reaction temperature is 80 °C and the reaction time is 30min. The catalyst Ti2SnC is the ideal catalyst for synthesis of ethyl acetate for good catalytic performance, non-corrosive to equipment, easily separated from product and used repeatedly.

Production of Low Calorie Oil with Enzymatic Catalysis Method

2012 ◽  
Vol 554-556 ◽  
pp. 1178-1182
Author(s):  
Hui Ling Cui ◽  
Yuan Dong Xu ◽  
Yu Jun Zhang ◽  
Hui Bo Song
Keyword(s):  
Reaction Time ◽  
Soybean Oil ◽  
Reaction Temperature ◽  
Orthogonal Experiment ◽  
Enzymatic Catalysis ◽  
Calorific Value ◽  
Molar Ratio ◽  
Reaction Yield ◽  
Low Calorie ◽  
Glycerol Triacetate

The 1, 3-specific lipase of Lipozymetlim was used as catalyst to produce low calorie oil through the reaction of soybean oil with glycerol triacetate. The effects of catalyst using amount, molar ratio of the substrates, reaction temperature and reaction time on the product yields were investigated. The orthogonal experiment results showed that the optimal reaction conditions were the substrate molar ratio of 2:1, reaction temperature of 60 °C, reaction time of 24 h, and 10 % enzyme adding amount per gram of substrate. Under such conditions, the reaction yield was 79.56 %. After 5 times reuse of the enzyme, the yield still could reach 58.94 %. The calorific value of the product was measured by calorimetric method and the value was 35 027 J/g which was about 75 % of the corresponding value for soybean oil.

Sign in / Sign up

Export Citation Format

Share Document