Synthesis of Single-Phase Nanocrystalline YIG by Co-Precipitation: The Influence of pH Value of Precursor Solution and Calcinating

2011 ◽  
Vol 311-313 ◽  
pp. 1294-1299 ◽  
Author(s):  
Liang Zheng ◽  
Hui Zheng ◽  
Jiang Xia Deng ◽  
Zhi Hua Ying ◽  
Jun Wu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Grain Size ◽  
Single Phase ◽  
Ph Value ◽  
Precursor Solution ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co Precipitation ◽  
Influence Of Ph ◽  
Scanning Electron

Single-phase nanocrystalline YIG powders have been successfully synthesized through chemical co-precipitation methods. The influence of pH value of the precursor solution and calcinating conditions (temperatures ranging from 700 to 900°C and times ranging from 0.5 to 12 hours) on the purity and grain size of the single-phase nanocrystalline YIG powders were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) technique. The results show that a pure single-phase YIG powder was obtained as the pH value of precursor solution above 10 and the YIG grain grows bigger as calcinating temperature and time increased. Finally, the optimal condition to form single-phase nanocrystalline YIG with the smallest grain size is calcinating at 750°C for 7 hours.

Influence of Annealing Time on Microstructure of Ni-W Alloys

2013 ◽  
Vol 747-748 ◽  
pp. 613-618
Author(s):  
Qiao Zhang ◽  
Shu Hua Liang ◽  
Chen Zhang ◽  
Jun Tao Zou
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Grain Size ◽  
Grain Boundaries ◽  
Annealing Time ◽  
Single Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Average Grain Size ◽  
Scanning Electron

The as-cast Ni-W alloys with 15wt%W, 25wt%W and 30wt%W were annealed in hydrogen at 1100. The effect of the annealing time on the microstructure of Ni-W alloys was studied, and the phase constituents and microstructure of annealed Ni-W alloys were characterized by the X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results showed that no any phase changed for Ni-15%W, Ni-25%W and Ni-30%W alloys annealed for 60 min, 90 min and 150 min, which were still consisted of single-phase Ni (W) solid solution. However, microstructure had a significant change after annealing. With increase of annealing time, the microstructure of Ni-15%W alloy became more uniform after annealing for 90 min, and the average grain size was 95μm, whereas the grain size of Ni-15%W alloy increased significantly after annealing for 150 min. For Ni-25%W and Ni-30%W, there was no obvious change on the grain size with increase of annealing time, and the amount of oxides at grain boundaries gradually reduced. After annealing for 150 min, the impurities at grain boundaries almost disappeared. Subsequently, the annealing at 1100 for 150 min was beneficial for the desired microstructure of Ni-25%W and Ni-30%W alloys.

scholarly journals Study on synthesizing Mg/Al layered double hydroxides at different pHs

2014 ◽  
Vol 15 ◽  
pp. 36-39 ◽  
Author(s):  
E Otgonjargal ◽  
G Burmaa ◽  
B Enkhmaa ◽  
M Enkhtuul ◽  
L Nyam-Ochir ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Ph Value ◽  
Infrared Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ph Values ◽  
Double Hydroxide ◽  
Double Hydroxides ◽  
Influence Of Ph ◽  
Scanning Electron

Mg/Al layered double hydroxide (LDH) was successfully synthesized at different pHs values. The Mg/AL LDH was well characterized by X-Ray diffraction and Fourier transform infrared analysis. The morphology of the LDH was observed using Scanning electron microscopy with energy dispersive X-ray spectroscopy. The influence of pH values on the morphology of the Mg/Al LDHs were studied. The result showed that the well-synthesized Mg/Al LDHs could be obtained when the pH value was about 10.0 at room temperature.DOI: http://doi.dx.org/10.5564/mjc.v15i0.319 Mongolian Journal of Chemistry 15 (41), 2014, p36-39

Synthesis of LiFePO4 Cathode Materials by a Chemical Method

2011 ◽  
Vol 675-677 ◽  
pp. 57-60
Author(s):  
Yuan Sun ◽  
Xiu Juan Zhao ◽  
Rui Ming Ren
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Chemical Method ◽  
Single Phase ◽  
Raw Materials ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co Precipitation ◽  
Scanning Electron

The olivine-type LiFePO4 powder was prepared by a chemical method using the synthesized FePO4⋅2H2O, LiOH and glucose as raw materials. The synthesized FePO4⋅2H2O powder was obtained by co-precipitation method. FePO4⋅2H2O and LiFePO4 powders were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results showed the synthesized FePO4⋅2H2O powder at pH of 2.05 was in a single phase and nearly spherical in shape. Using the synthesized powders to prepared LiFePO4 at 600 °C in vacuum for 2 h was nearly spherical in shape and whose size was in the range of 0.1-0.5μm.

Preparation and Characteristics of FePO4·xH2O Powder

2011 ◽  
Vol 675-677 ◽  
pp. 77-80 ◽  
Author(s):  
Hai Li Jing ◽  
Guo Jun Li ◽  
Rui Ming Ren
Keyword(s):  
Electron Microscopy ◽  
Single Phase ◽  
Xrd Analysis ◽  
Preparation Process ◽  
Test Results ◽  
X Ray Diffraction ◽  
Crystal Water ◽  
X Ray ◽  
Co Precipitation ◽  
Scanning Electron

Nano-sized precursor FePO4·xH2O particles were obtained by oxidation co-precipitation using FeSO4⋅7H2O, H2O2 and ammonia. The powder was characterized by differential thermal analysis (DTA) and thermogravimetry (TG), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The TG-DTA results determined the content of crystal water of FePO4·xH2O, i.e. x = 1.5. The SEM observation suggested that FePO4·xH2O particles were spherical in shape and its grain size was about 150 nanometers. The dispersion of the synthesized powder was improved through the addition of surfactant. The XRD analysis indicated that the synthesized FePO4·xH2O was amorphous. After being calcined at 720 °C for 10 hrs, the synthesized FePO4·xH2O at pH of ~3.5 was crystallized and FePO4 in a single phase was obtained. According to the test results, the optimized preparation process parameters were determined.

Preparation of Borosilicate Xerogel and Research on its Mineralization

2012 ◽  
Vol 476-478 ◽  
pp. 2059-2062
Author(s):  
Chen Wang ◽  
Ya Dong Li ◽  
Gu Qiao Ding
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Infrared Spectroscopy ◽  
Ph Value ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Compositional Changes ◽  
Scanning Electron

Tributyl borate was first adopted for the introduction of boron in the preparation of bioactive borosilicate xerogel by sol-gel method. The xerogel reacted continuously in 0.25M K2HPO4 solution with a starting pH value of 7.0 at 37 °C for 1day. The structural, morphologies and compositional changes resulting from the conversion were characterized using X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy. The results indicated that speed of formation of HA was cut way back on the time with the addition of boron and the induction period for the HA nucleation on the surface of the borosilicate xerogel was short than 1 days. The conversion mechanism of the borosilicate xerogels to hydroxyapaptite was also discussed.

Crystal Chemistry and Phase Equilibrium Studies of the Bao(baco3)‐r2o3‐cuo Systems. V. Melting Relations in ba2(y,nd,eu)cu3o6+x

1989 ◽  
Vol 169 ◽  
Author(s):  
Winnie Wong‐Ng ◽  
Lawrence P. Cook ◽  
Michael D. Hill ◽  
Boris Paretzkin ◽  
E.R. Fuller
Keyword(s):  
Electron Microscopy ◽  
Single Phase ◽  
X Ray Diffraction ◽  
Equilibrium Studies ◽  
X Ray ◽  
Helium Gas ◽  
Ionic Size ◽  
Differential Thermogravimetric Analysis ◽  
Melting Relations ◽  
Scanning Electron

AbstractThe influence of the ionic size of the lanthanides R on melting relations of Ba2RCu3O6+x, where R=Y, Eu and Nd, was studied and compared with that of a high Tc superconductor mixed‐lanthanide phase Ba2(Y.75Eu.125Nd 125)Cu3O6+xThese materials have been characterized by a variety of methods including differential thermogravimetric analysis (DTA), scanning electron microscopy (SEM) with energy dispersive X‐ray spectroscopy (EDX) and X‐ray powder diffraction. Single phase samples of Ba2(Y.75Eu.125Nd.125)Cu3O6+x were annealed at 1004, 1040, 1052, 1060, 1078, 1107 and 1160°C and quenched into a helium gas container cooled by liquid nitrogen. The SEM micrographs of these samples showed the progressive chnages in features of the microstructures from sintering and grain growth through melting and then recrystallization from the melt. The addition of the SEM technique in conjunction with X‐ray diffraction has been helpful in the study of phase equilibria in this system.

The Synthesis of Cu0.81Ni0.19 Intermetallics by Mechanical Alloying

2012 ◽  
Vol 496 ◽  
pp. 379-382
Author(s):  
Rui Song Yang ◽  
Ming Tian Li ◽  
Chun Hai Liu ◽  
Xue Jun Cui ◽  
Yong Zhong Jin
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Mechanical Alloying ◽  
Milling Time ◽  
Elemental Powder ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scherrer Equation ◽  
Scanning Electron

The Cu0.81Ni0.19 has been synthesized directly from elemental powder of nickel and copper by mechanical alloying. The alloyed Cu0.81Ni0.19 alloy powders are prepared by milling of 8h. The grain size calculated by Scherrer equation of the NiCu alloy decreased with the increasing of milling time. The end-product was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM)

scholarly journals Hydrothermal synthesis and characteristics of lanthanumdoped pb(Zr₀.₆₅Ti ₀.₃₅)O₃ ceramics

2021 ◽  
Vol 8 (3) ◽  
pp. 14-19
Author(s):  
Thuy Nguyen Thanh ◽  
Tung Nguyen Van ◽  
Hung Nguyen Trong ◽  
Minh Cao Duy
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Dielectric Constant ◽  
Reaction Temperature ◽  
Lead Zirconate Titanate ◽  
Lead Zirconate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Influence Of Ph ◽  
Scanning Electron

Lanthanum-doped lead zirconate titanate (PLZT) powders were synthesized using thehydrothermal method. The influence of pH, reaction temperature and time, lanthanum concentration on the formation and characteristics of PLZT were investigated. Obtained powders were investigated using X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) techniques and a dielectric analyzer. The results showed that           Pb1-xLax(Zr0.65Ti0.35)O3 with x= 0.0 – 0.1 were well formed under conditions: pH≥13, reaction time of 12hrs, reaction temperature of 180oC. Dielectric constant of PLZT is higher than PZT. The grain size of the PLZT is found to be 1–3.5 µm.

Light Burning Condition of Preparing Dolomite Clinker Using Natural Dolomite

2018 ◽  
Vol 281 ◽  
pp. 156-162
Author(s):  
Wang Nian Zhang ◽  
Xi Tang Wang ◽  
Zhou Fu Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Grain Size ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Burning Temperature ◽  
X Ray ◽  
Temperature Range ◽  
Scanning Electron

The influence of the light burning temperature on the sintering property of nature dolomite has been investigated by two-step sintering process in the temperature range 1500 °C to 1600 °C. The resulting bulk densities and apparent porosities of the sintered dolomite samples were examined, and analyzing the sintered dolomite by scanning electron microscopy and X-ray diffraction were performed. The results showed light burned at 850 °C for 3 h, the main phases of the dolomite with 3-5 grain size were MgO, CaO and little CaCO3, and then fired at 1600 °C,the density of sintering dolomite reached to 3.38 g/cm3, the apparent property was 1.2 %, the size of MgO grain up to 3.75 μm . However when dolomite light burned at 1050 °C for 3 h, the main phases were MgO and CaO, and then fired at 1600 °C,the density of sintering dolomite only was 3.30 g/cm3, the apparent property was 2.3 %, the size of MgO only was 3.05 μm .

scholarly journals Layer-by-Layer Self-Assembled Ferrite Multilayer Nanofilms for Microwave Absorption

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Jiwoong Heo ◽  
Daheui Choi ◽  
Jinkee Hong
Keyword(s):  
Electron Microscopy ◽  
Self Assembly ◽  
Precursor Solution ◽  
Ferrite Nanoparticles ◽  
Energy Dispersive ◽  
Layer By Layer ◽  
X Ray Diffraction ◽  
Simple Method ◽  
X Ray ◽  
Scanning Electron

We demonstrate a simple method for fabricating multilayer thin films containing ferrite (Co0.5Zn0.5Fe2O4) nanoparticles, using layer-by-layer (LbL) self-assembly. These films have microwave absorbing properties for possible radar absorbing and stealth applications. To demonstrate incorporation of inorganic ferrite nanoparticles into an electrostatic-interaction-based LbL self-assembly, we fabricated two types of films: (1) a blended three-component LbL film consisting of a sequential poly(acrylic acid)/oleic acid-ferrite blend layer and a poly(allylamine hydrochloride) layer and (2) a tetralayer LbL film consisting of sequential poly(diallyldimethylammonium chloride), poly(sodium-4-sulfonate), bPEI-ferrite, and poly(sodium-4-sulfonate) layers. We compared surface morphologies, thicknesses, and packing density of the two types of ferrite multilayer film. Ferrite nanoparticles (Co0.5Zn0.5Fe2O4) were prepared via a coprecipitation method from an aqueous precursor solution. The structure and composition of the ferrite nanoparticles were characterized by X-ray diffraction, energy dispersive X-ray spectroscopy, transmission electron microscopy, and scanning electron microscopy. X-ray diffraction patterns of ferrite nanoparticles indicated a cubic spinel structure, and energy dispersive X-ray spectroscopy revealed their composition. Thickness growth and surface morphology were measured using a profilometer, atomic force microscope, and scanning electron microscope.

Sign in / Sign up

Export Citation Format

Share Document