Study on Cutting Forces of Mg-6Nd-4Gd-3Y Magnesium Alloy in High-Speed Milling

2011 ◽  
Vol 338 ◽  
pp. 709-713
Author(s):  
Zhen Hua Wang ◽  
Jun Tang Yuan
Keyword(s):  
Magnesium Alloy ◽  
Cutting Force ◽  
Cutting Forces ◽  
High Speed ◽  
Polynomial Regression ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Partial Least Square ◽  
Depth Of Cut ◽  
High Speed Milling

In this paper, 24full factorial design and homogeneous design were applied to the high-speed milling experiments for Mg-6Nd-4Gd-3Y magnesium alloy. According to the experimental results of cutting force, the effect of cutting parameters (cutting speed, feed per tooth, depth of cut, and width of cut) on cutting force was discussed, and the nonlinear polynomial regression models of cutting forces based on the cutting parameters were presented by the partial least-square regression.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

Influence on Cutting Forces and Vibration in High Speed Machining Pocket Corner

2011 ◽  
Vol 189-193 ◽  
pp. 3084-3088
Author(s):  
De Wen Tang ◽  
Ru Shu Peng ◽  
Rui Lan Zhao
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
High Speed ◽  
Sudden Change ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Poor Quality ◽  
Depth Of Cut ◽  
Processing Efficiency ◽  
Radial Depth

High speed milling hardened mould steel (above HRC50) at pocket corner generates the cutting forces increase and vibration gets fiercely because of the sudden change of cutting direction. It will cause serious wear and possible breakage of cutting tool, and poor quality of parts. Hence, the need to select reasonable cutting parameters and adopt appropriate cutting strategies will help them to achieve their goal. In this paper, the effects cutting parameters including cutting speed, pocket corner angle, feed rate per tooth and radial depth of cut on cutting force and vibration are studied. The results show that sharper pocket corner results in the increase of cutting force and makes vibration strong. Cutting force increase with the increase of cutting speeding, feed per tooth and radial depth of cut. The optimum of cutting speed leads to the decrease of vibration. It is proposed that cutting parameters should be optimized to improve tool life and processing efficiency.

Cutting Performance of Diamond Coated, TiAlN Coated and Carbide Cutting Tools in High Speed Milling Graphite

2014 ◽  
Vol 800-801 ◽  
pp. 451-459
Author(s):  
Yu Hai Zhou ◽  
Cheng Yong Wang ◽  
Qi Ming Wang
Keyword(s):  
Cutting Force ◽  
Cutting Forces ◽  
High Speed ◽  
Orthogonal Experiment ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
Cutting Performance ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

This paper focusing on cutting performance high speed milling Electrical Discharging Machining (EDM) graphite with diamond coated、Carbide (WC) and TiAlN coated cutting Tools. tools wear, cutting force and machined surface had been researched. Experiment study including cutting speed, feed rate per tooth, radial depth of cut, axial depth of cut, and material of tools factors effects on the cutting forces. Cutting parameters are optimized based on the orthogonal experiment. Experiment in high speed milling with diamond coated tools all comparison with TiAlN coated and Carbide (WC) tools. On the surface quality, cutting forces and tool wear influence graphite cutting tool materials research, process parameters, tool design and optimization of processing parameters to provide supportive data. The minimum cutting force as the goal, through the orthogonal experiment for the optimization of cutting parameters obtained for the high speed milling graphite with diamond-coated tool: cutting force 360m/min,feed per tooth 0.15mm/z, radial depth of cut 0.9mm, axial depth of 9mm.

scholarly journals Surface Quality Assessment after Milling AZ91D Magnesium Alloy Using PCD Tool

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 617 ◽  
Author(s):  
Ireneusz Zagórski ◽  
Jarosław Korpysa
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Roughness Parameters ◽  
Operational Parameters

Surface roughness is among the key indicators describing the quality of machined surfaces. Although it is an aggregate of several factors, the condition of the surface is largely determined by the type of tool and the operational parameters of machining. This study sought to examine the effect that particular machining parameters have on the quality of the surface. The investigated operation was the high-speed dry milling of a magnesium alloy with a polycrystalline diamond (PCD) cutting tool dedicated for light metal applications. Magnesium alloys have low density, and thus are commonly used in the aerospace or automotive industries. The state of the Mg surfaces was assessed using the 2D surface roughness parameters, measured on the lateral and the end face of the specimens, and the end-face 3D area roughness parameters. The description of the surfaces was complemented with the surface topography maps and the Abbott–Firestone curves of the specimens. Most 2D roughness parameters were to a limited extent affected by the changes in the cutting speed and the axial depth of cut, therefore, the results from the measurements were subjected to statistical analysis. From the data comparison, it emerged that PCD-tipped tools are resilient to changes in the cutting parameters and produce a high-quality surface finish.

Cutting Forces in High Speed Milling of Hardened Steel by Coated Tool

2009 ◽  
Vol 69-70 ◽  
pp. 418-422
Author(s):  
L.D. Wu ◽  
Cheng Yong Wang ◽  
D.H. Yu ◽  
Yue Xian Song
Keyword(s):  
Cutting Forces ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Coated Tool ◽  
Radial Depth ◽  
Solid Carbide ◽  
End Mills

Hardened steel P20 at 50 HRC is milled at high speed by TiN coated and TiAlN coated solid carbide straight end mills, and the cutting forces and tool wear are measured. The result shows that TiAlN coated tool is more suitable for cutting hardened steel at high speed. Then the hardened steel is milled under different cutting parameters. It is indicated that the effect of cutting speed on cutting forces is small, but the effect of cutting speed on machine vibration should be considered. Increase feed per tooth or radial depth of cut will increase the cutting forces.

Experimental Investigations of Cutting Parameters Influence on Cutting Forces and Surface Roughness of Quartz Glass

2013 ◽  
Vol 641-642 ◽  
pp. 367-370
Author(s):  
Gui Qiang Liang ◽  
Fei Fei Zhao
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Forces ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Diamond Wheel ◽  
Experimental Investigations ◽  
Depth Of Cut ◽  
Feed Force

Abstract In the present study, an attempt has been made to investigate the effect of cutting parameters (cutting speed, feed rate and depth of cut) on cutting forces (feed force, thrust force and cutting force) and surface roughness in milling of Quartz glas using diamond wheel. The cutting process in the up-cut milling of glass is discussed and the cutting force measured. The cutting force gradually increases with the cutter rotation at the beginning of the cut, and oscillates about a constant mean value after a certain undeformed chip thickness. The results show that cutting forces and surface roughness do not vary much with experimental cutting speed in the range of 55–93 m/min. The suggested models of cutting forces and surface roughness and adequately map within the limits of the cutting parameters considered.

The Research on Milling Force in High-Speed Milling Nickel-Based Superalloy of Inconel 718

2013 ◽  
Vol 395-396 ◽  
pp. 1031-1034
Author(s):  
Can Zhao ◽  
Yu Bo Liu
Keyword(s):  
Cutting Force ◽  
Inconel 718 ◽  
High Speed ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Depth ◽  
Milling Force ◽  
High Speed Milling ◽  
Nickel Based Superalloy ◽  
Cutting Speeds

This paper makes an experiment in high-speed milling of Inconel 718. Cutting tests were performed using round and ceramic tools, at feeds from 0.06 to 0.14 mm/tooth, Axial Depth of Cut from0.5 to 1.5mm,and cutting speeds ranging from 500 to 1037 m/min. The behaviour of the cutting forces during machining was then measure. The results show that cutting force increases first and then decreases with the increase of feed per tooth, the tool chipping and groove wear were found with the increase of axial cutting depth, and cutting force is increased; the increase in cutting force with the cutting speed increases, when the cutting speed reaches a critical speed, the cutting force as the cutting speed increases began to decline.

Study of High-Speed Machining Parameters on Nickel-Based Alloy GH2132

2011 ◽  
Vol 189-193 ◽  
pp. 3142-3147 ◽  
Author(s):  
Dong Qiang Gao ◽  
Zhong Yan Li ◽  
Zhi Yun Mao
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Speed ◽  
Main Tool ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
High Speed Machining ◽  
Nickel Based Alloy

A model of stress and temperature field is established on nickel-based alloy cutting by finite element modeling and dynamic numerical simulating, and then combining high-speed machining test and orthogonality analysis method, the influence law of cutting parameters on the cutting force and tool wear has been researched, and the tool life and cutting force prediction model based on cutting parameters has been obtained. Finally, by genetic algorithm method cutting parameters are selected reasonably and optimized. The result shows that the bonding wear is main tool wear, and the influence of cutting speed on cutting force is smaller than feed per tooth and axial depth of cut.

Cutting Force in High-Speed Face Milling AISI H13 Steel

2015 ◽  
Vol 667 ◽  
pp. 35-40
Author(s):  
Xiao Bin Cui ◽  
Jing Xia Guo ◽  
Xiao Yang Wang
Keyword(s):  
Cutting Force ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Face Milling ◽  
Depth Of Cut ◽  
H13 Steel ◽  
Aisi H13 Steel ◽  
Aisi H13 ◽  
Axial Depth

For the purpose of acquiring thorough understanding of the characteristics of cutting force in high and ultra-high-speed face milling of hardened steel, experimental investigations on face milling of AISI H13 steel (46-47 HRC) are conducted in the present study. The cutting speed of 1400 m/min, at which relatively low cutting force and relatively low surface roughness can be obtained at the same time, is considered as a critical value for both mechanical load and surface finish. The Taguchi method is applied to investigate the effects of cutting parameters on cutting force in different speed ranges (below and above 1400 m/min). In different speed ranges, the contribution order of the cutting parameters for the resultant cutting force is the same, namely axial depth of cut, cutting speed and feed per tooth. However, the contributions of cutting speed and feed per tooth increase substantially as the cutting speed surpasses 1400 m/min. Within the range of cutting parameters used in the present study, the optimum cutting conditions for the cutting force are cutting speed 200 m/min, feed per tooth 0.02 mm/tooth and axial depth of cut 0.1 mm.

Effect of Various Cooling Strategies on Surface Roughness of High Speed Milling Ti-6Al-4V

2011 ◽  
Vol 697-698 ◽  
pp. 49-52 ◽  
Author(s):  
Xiao Yong Yang ◽  
Cheng Zu Ren ◽  
Guang Chen ◽  
Bing Han ◽  
Y. Wang
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Side Milling ◽  
High Speed Milling ◽  
Cooling Strategies ◽  
Radial Depth

This study focused on the side milling surface roughness of titanium alloy under various cooling strategies and cutting parameters. The experimental results show that the cooling strategies significantly affect the surface roughness in milling Ti-6Al-4V. Surface roughness (Ra) alterations are investigated. Cutting fluid strategy made nearly all the smallest and most stable roughness values. The surface roughness values produced by all cooling strategies are obviously affected by feed, radial depth-of-cut and cutting speed. However, axial depth-of-cut has little influence.

Sign in / Sign up

Export Citation Format

Share Document