Effect of Various Cooling Strategies on Surface Roughness of High Speed Milling Ti-6Al-4V

2011 ◽  
Vol 697-698 ◽  
pp. 49-52 ◽  
Author(s):  
Xiao Yong Yang ◽  
Cheng Zu Ren ◽  
Guang Chen ◽  
Bing Han ◽  
Y. Wang
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Side Milling ◽  
High Speed Milling ◽  
Cooling Strategies ◽  
Radial Depth

This study focused on the side milling surface roughness of titanium alloy under various cooling strategies and cutting parameters. The experimental results show that the cooling strategies significantly affect the surface roughness in milling Ti-6Al-4V. Surface roughness (Ra) alterations are investigated. Cutting fluid strategy made nearly all the smallest and most stable roughness values. The surface roughness values produced by all cooling strategies are obviously affected by feed, radial depth-of-cut and cutting speed. However, axial depth-of-cut has little influence.

Experimental Studies on Cutting Temperature of Nickel-Based Supper Alloy Inconel 718

2013 ◽  
Vol 584 ◽  
pp. 20-23
Author(s):  
Mao Hua Xiao ◽  
Ning He ◽  
Liang Li ◽  
Xiu Qing Fu
Keyword(s):  
Inconel 718 ◽  
High Speed ◽  
Experimental Studies ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth ◽  
The Impact

The method to measure the cutting speed when high speed milling nickel alloy Inconel 718 based on semi-artificial thermocouple. The cutting parameters, tool wear and so on the cutting temperature were analyzed. The tests showed that the temperature was gradually increased with the increase of cutting speed. The cutting speed must be more than 600m/min, when the ceramic tools would perform better cutting performance in the high-speed milling nickel-based superalloy. In order to achieve more efficient machining, milling speed can be increased to more than 1000m/min. The impact amount of Radial depth of cut and feed per tooth were relatively small.

Parameters Optimization Research of High-Speed Milling PM60 Mould Steel Based on Taguchi Method

2016 ◽  
Vol 861 ◽  
pp. 75-83
Author(s):  
Ying Xing Xie ◽  
Cheng Yong Wang ◽  
Feng Ding ◽  
Wen Huang
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
High Speed ◽  
High Hardness ◽  
Cutting Parameters ◽  
Parameters Optimization ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth ◽  
Optimal Cutting Parameters

In order to obtain better surface quality after high speed milling high hardness mold steel, and reduce tool wear in cutting process, prolong the service life of cutting tools, obtain superior levels and optimal combination of cutting parameters in the test range. Through the design of orthogonal experiment, the use of Taguchi method, and noise ratio analysis and variance analysis of dry cutting high hardness mould steel PM60 under different cutting parameters; and finally, the optimal cutting parameters of surface roughness and cutting force value were predicted and verified. Research showed that: the worst cutting parameters influenced the surface roughness Ra was radial depth of cut ae, its influence was highly significant, followed by spindle speed n and depth of axial cut ap; the most serious impact cutting parameter of cutting force F was the feed speed vf, followed by the spindle speed n and radial depth of cut ae; verification test showed that the optimal cutting parameters combination were reasonable and the calculation errors of the predicted values and experimental values were very small, indicating that Taguchi method in cutting parameters optimization of cutting mould steel PM60 was valid.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

A Comprehensive Study on Surface Roughness in Machining of AISI D2 Hardened Steel

2012 ◽  
Vol 576 ◽  
pp. 60-63 ◽  
Author(s):  
N.A.H. Jasni ◽  
Mohd Amri Lajis
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Depth Of Cut ◽  
Feed Speed ◽  
Radial Depth ◽  
Aisi D2 ◽  
Coated Carbide

Hard milling of hardened steel has wide application in mould and die industries. However, milling induced surface finish has received little attention. An experimental investigation is conducted to comprehensively characterize the surface roughness of AISI D2 hardened steel (58-62 HRC) in end milling operation using TiAlN/AlCrN multilayer coated carbide. Surface roughness (Ra) was examined at different cutting speed (v) and radial depth of cut (dr) while the measurement was taken in feed speed, Vf and cutting speed, Vc directions. The experimental results show that the milled surface is anisotropic in nature. Surface roughness values in feed speed direction do not appear to correspond to any definite pattern in relation to cutting speed, while it increases with radial depth-of-cut within the range 0.13-0.24 µm. In cutting speed direction, surface roughness value decreases in the high speed range, while it increases in the high radial depth of cut. Radial depth of cut is the most influencing parameter in surface roughness followed by cutting speed.

SURFACE ROUGHNESS OF MAGNESIUM ALLOY AZ91D IN HIGH SPEED MILLING

2016 ◽  
Vol 78 (6-9) ◽  
Author(s):  
Mohd Shahfizal Ruslan ◽  
Kamal Othman ◽  
Jaharah A.Ghani ◽  
Mohd Shahir Kassim ◽  
Che Hassan Che Haron
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
Feed Rate ◽  
High Speed ◽  
Cutting Parameters ◽  
Experimental Result ◽  
Depth Of Cut ◽  
Polishing Process ◽  
High Speed Cutting ◽  
Radial Depth

Magnesium alloy is a material with a high strength to weight ratio and is suitable for various applications such as in automotive, aerospace, electronics, industrial, biomedical and sports. Most end products require a mirror-like finish, therefore, this paper will present how a mirror-like finishing can be achieved using a high speed face milling that is equivalent to the manual polishing process. The high speed cutting regime for magnesium alloy was studied at the range of 900-1400 m/min, and the feed rate for finishing at 0.03-0.09 mm/tooth. The surface roughness found for this range of cutting parameters were between 0.061-0.133 µm, which is less than the 0.5µm that can be obtained by manual polishing. Furthermore, from the S/N ratio plots, the optimum cutting condition for the surface roughness can be achieved at a cutting speed of 1100 m/min, feed rate 0.03 mm/tooth, axial depth of cut of 0.20 mm and radial depth of cut of 10 mm. From the experimental result the lowest surface roughness of 0.061µm was obtained at 900 m/min with the same conditions for other cutting parameters. This study revealed that by milling AZ91D at a high speed cutting, it is possible to eliminate the polishing process to achieve a mirror-like finishing.

Tool Wear Characteristics in High Speed Milling of Ti-6Al-4V Alloy with Nitrogen Gas Medium

2006 ◽  
Vol 315-316 ◽  
pp. 588-592 ◽  
Author(s):  
Wei Zhao ◽  
Ning He ◽  
Liang Li ◽  
Z.L. Man
Keyword(s):  
Tool Wear ◽  
High Speed ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth ◽  
Oil Mist ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes

High speed milling experiments using nitrogen-oil-mist as cutting medium were undertaken to investigate the characteristics of tool wear for Ti-6Al-4V Alloy, a kind of important and commonly used titanium alloy in the aerospace and automobile industries. Uncoated carbide tools have been applied in the experiments. The cutting speed was 300 m/min. The axial depth of cut and the radial depth of cut were kept constant at 5.0 mm and 1.0 mm, respectively. The feed per tooth was 0.1 mm/z. Optical and scanning electron microscopes have been utilized to determine the wear mechanisms of the cutting tools, and energy spectrum analysis has been carried out to measure the elements distribution at the worn areas. Meanwhile, comparisons were made to discuss the influence of different cutting media such as nitrogen-oil-mist and air-oil–mist upon the tool wear. The results of this investigation indicate that the tool life in nitrogen-oil-mist is significantly longer than that in air-oil-mist, and nitrogen-oil-mist is more suitable for high speed milling of Ti-6Al-4V alloy than air-oil-mist.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

scholarly journals Surface Quality Assessment after Milling AZ91D Magnesium Alloy Using PCD Tool

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 617 ◽  
Author(s):  
Ireneusz Zagórski ◽  
Jarosław Korpysa
Keyword(s):  
Surface Roughness ◽  
Magnesium Alloy ◽  
High Speed ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Roughness Parameters ◽  
Operational Parameters

Surface roughness is among the key indicators describing the quality of machined surfaces. Although it is an aggregate of several factors, the condition of the surface is largely determined by the type of tool and the operational parameters of machining. This study sought to examine the effect that particular machining parameters have on the quality of the surface. The investigated operation was the high-speed dry milling of a magnesium alloy with a polycrystalline diamond (PCD) cutting tool dedicated for light metal applications. Magnesium alloys have low density, and thus are commonly used in the aerospace or automotive industries. The state of the Mg surfaces was assessed using the 2D surface roughness parameters, measured on the lateral and the end face of the specimens, and the end-face 3D area roughness parameters. The description of the surfaces was complemented with the surface topography maps and the Abbott–Firestone curves of the specimens. Most 2D roughness parameters were to a limited extent affected by the changes in the cutting speed and the axial depth of cut, therefore, the results from the measurements were subjected to statistical analysis. From the data comparison, it emerged that PCD-tipped tools are resilient to changes in the cutting parameters and produce a high-quality surface finish.

scholarly journals OPTIMUM PERFORMANCE OF GREEN MACHINING ON THIN WALLED TI6AL4V USING RSM AND ANN IN TERMS OF CUTTING FORCE AND SURFACE ROUGHNESS

2019 ◽  
Vol 81 (6) ◽  
Author(s):  
Muhammad Yanis ◽  
Amrifan Saladin Mohruni ◽  
Safian Sharif ◽  
Irsyadi Yani
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Ann Model ◽  
Green Machining ◽  
Radial Depth ◽  
Thin Walled

Thin walled titanium alloys are mostly applied in the aerospace industry owing to their favorable characteristic such as high strength-to-weight ratio. Besides vibration, the friction at the cutting zone in milling of thin-walled Ti6Al4V will create inconsistencies in the cutting force and increase the surface roughness. Previous researchers reported the use of vegetable oils in machining metal as an effort towards green machining in reducing the undesirable cutting friction. Machining experiments were conducted under Minimum Quantity Lubrication (MQL) using coconut oil as cutting fluid, which has better oxidative stability than other vegetable oil. Uncoated carbide tools were used in this milling experiment. The influence of cutting speed, feed and depth of cut on cutting force and surface roughness were modeled using response surface methodology (RSM) and artificial neural network (ANN). Experimental machining results indicated that ANN model prediction was more accurate compared to the RSM model. The maximum cutting force and surface roughness values recorded are 14.89 N, and 0.161 µm under machining conditions of 125 m/min cutting speed, 0.04 mm/tooth feed, 0.25 mm radial depth of cut (DOC) and 5 mm axial DOC. 

Experimental Investigation on High-Speed Milling of Aluminum Alloys

2011 ◽  
Vol 418-420 ◽  
pp. 1141-1147
Author(s):  
Yong Liu ◽  
Li Tang Zhang ◽  
Zhi Hong Xu
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Experimental Investigation ◽  
Aluminum Alloys ◽  
High Speed ◽  
Depth Of Cut ◽  
Processing Temperature ◽  
Single Factor ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling is recognized as one of rapidly development machining methods. The article gives details of machining experiments with different aluminum alloys. Through a lot of single factor experiments and the orthogonal multi-factor experiments, and also use method of semi-artificial thermocouple. This paper mainly studies influence of surface roughness and residual stress with changed rotate speed, tooth load and radial depth of cut, and changed law of processing temperature for rotate speed. Though experiments shows that enhancing rotate speed may reduce surface roughness and residual stress within certain limits and the result of experiments is not agree with Carl Salomon’s theory.

Sign in / Sign up

Export Citation Format

Share Document