Longitudinal Aerodynamics of a Canard Guided Spin Stabilized Projectile

2012 ◽  
Vol 443-444 ◽  
pp. 719-723
Author(s):  
Xiu Ling Ji ◽  
Hai Peng Wang ◽  
Shi Ming Zeng ◽  
Chen Yang Jia
Keyword(s):  
Normal Force ◽  
Navier Stokes ◽  
Test Case ◽  
Aerodynamic Coefficients ◽  
Number Range ◽  
Detailed Understanding ◽  
Pitch Moment ◽  
Spinning Projectile ◽  
Mach 3 ◽  
Viable Approach

Navier–Stokes simulation is performed on a canard guided spinning projectile for different attack angles and circumferential position angles of canard over the Mach number range of 1.8–2.2. The computational Magnus moment coefficients of test case are validated with available experimental data of a Secant-Ogive-Cylinder-Boattail (SOCBT) configuration at Mach 3, demonstrating that the method can provide an accurate and viable approach for this problem. The aim of the present study is to provide a detailed understanding of the effects of canard with different circumferential position angles on longitudinal aerodynamic coefficients at three supersonic speeds and various angles of attack. And the results show that normal force coefficients and pitch moment coefficients vary periodically with the circumferential position angles of canard.

Multiscale Partially Averaged Navier Stokes Approach for the Prediction of Flow in Linear Compressor Cascade With Moving Casing

2011 ◽  
Author(s):  
Domenico Borello ◽  
Giovanni Delibra ◽  
Franco Rispoli
Keyword(s):  
Turbulence Models ◽  
Navier Stokes ◽  
Test Case ◽  
Compressor Cascade ◽  
Preliminary Assessment ◽  
Linear Compressor ◽  
Tip Leakage ◽  
Experimental Campaign ◽  
Elliptic Relaxation ◽  
Linear Compressor Cascade

In this paper we present an innovative Partially Averaged Navier Stokes (PANS) approach for the simulation of turbomachinery flows. The elliptic relaxation k-ε-ζ-f model was used as baseline Unsteady Reynolds Averaged Navier Stokes (URANS) model for the derivation of the PANS formulation. The well established T-FlowS unstructured finite volume in-house code was used for the computations. A preliminary assessment of the developed formulation was carried out on a 2D hill flow that represents a very demanding test case for turbulence models. The turbomachinery flow here investigated reproduces the experimental campaign carried out at Virginia Tech on a linear compressor cascade with tip leakage. Their measurements were used for comparisons with numerical results. The predictive capabilities of the model were assessed through the analysis of the flow field. Then an investigation of the blade passage, where experiments were not available, was carried out to detect the main loss sources.

URANS Studies of Effect of Eccentricity on Ship–Lock Interactions

2016 ◽  
Vol 13 (04) ◽  
pp. 1641012
Author(s):  
Qingjie Meng ◽  
Decheng Wan
Keyword(s):  
Viscous Flow ◽  
Hydrodynamic Interaction ◽  
Vertical Displacement ◽  
Navier Stokes ◽  
Test Case ◽  
The Third ◽  
Surface Pressure Distribution ◽  
Sst Turbulence Model ◽  
Unsteady Viscous Flow ◽  
Ship Lock

The unsteady viscous flow around a 12000TEU ship model entering the Third Set of Panama Locks with different eccentricity is simulated by solving the unsteady Reynolds averaged Navier–Stokes (RANS) equations in combination with the [Formula: see text]SST turbulence model. Overset grid technology is utilized to maintain grid orthogonality and the effects of the free surface are taken into account. The hydrodynamic forces, vertical displacement as well as surface pressure distribution are predicted and analyzed. First, a benchmark test case is designed to validate the capability of the present methods in the prediction of the viscous flow around the ship when maneuvering into the lock. The accumulation of water in front of the ship during entry into a lock is noticed. A set of systematic computations with different eccentricity are then carried out to examine the effect of eccentricity on the ship–lock hydrodynamic interaction.

Two Dimensional Simulations of Enhanced Heat Transfer in an Intermittently Grooved Channel

2000 ◽  
Author(s):  
M. Greiner ◽  
P. F. Fischer ◽  
H. M. Tufo
Keyword(s):  
Heat Transfer ◽  
Local Heat Transfer ◽  
Spectral Element ◽  
Local Heat ◽  
Navier Stokes ◽  
Computational Domain ◽  
Two Dimensional ◽  
Number Range ◽  
Element Technique ◽  
Outflow Boundary

Abstract Two-dimensional Navier-Stokes simulations of heat and momentum transport in an intermittently grooved passage are performed using the spectral element technique for the Reynolds number range 600 ≤ Re ≤ 1800. The computational domain has seven contiguous transverse grooves cut symmetrically into opposite walls, followed by a flat section with the same length. Periodic inflow/outflow boundary conditions are employed. The development and decay of unsteady flow is observed in the grooved and flat sections, respectively. The axial variation of the unsteady component of velocity is compared to the local heat transfer, shear stress and pressure gradient. The results suggest that intermittently grooved passages may offer even higher heat transfer for a given pumping power than the levels observed in fully grooved passages.

Effect of Scaling of Blade Row Sectors on the Prediction of Aerodynamic Forcing in a Highly-Loaded Transonic Compressor Stage

2009 ◽  
Author(s):  
Mari´a A. Mayorca ◽  
Jesu´s A. De Andrade ◽  
Damian M. Vogt ◽  
Hans Ma˚rtensson ◽  
Torsten H. Fransson
Keyword(s):  
Second Harmonic ◽  
Harmonic Excitation ◽  
Navier Stokes ◽  
Test Case ◽  
Moderate Amount ◽  
Object A ◽  
Transonic Compressor ◽  
Geometrical Scaling ◽  
Direct Indication ◽  
Generalized Force

An investigation of the sensitivity of a geometrical scaling technique on the blade forcing prediction and mode excitability has been performed. A stage of a transonic compressor is employed as test object. A scaling ratio is defined which indicates the amount of scaling from the original geometry. Different scaling ratios are selected and 3D Navier Stokes unsteady calculations completed for each scaled configuration. A full annulus calculation (non-scaled) is performed serving as reference. The quantity of interest is the generalized force, which gives a direct indication of the mode excitability. In order to capture both up- and downstream excitation effects the mode excitability has been assessed on both rotor and stator blades. The results show that first harmonic excitation can be predicted well for both up- and downstream excitation using moderate amount of scaling. On the other hand, the predictions of second harmonic quantities do show a higher sensitivity to scaling for the investigated test case.

Database of Sail Shapes vs. Sail Performance and Validation of Numerical Calculation for Upwind Condition

2007 ◽  
Author(s):  
Yutaka Masuyama ◽  
Yusuke Tahara ◽  
Toichi Fukasawa ◽  
Naotoshi Maeda
Keyword(s):  
Numerical Method ◽  
Vortex Lattice ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Numerical Calculations ◽  
Navier Stokes ◽  
Coupling Scheme ◽  
Aerodynamic Coefficients ◽  
Lattice Method ◽  
Cfd Method

Database of full-scale three-dimensional sail shapes are presented with the aerodynamic coefficients for the upwind condition of IMS type sails. Three-dimensional shape data are used for the input of numerical calculations and the results are compared with the measured sail performance. The sail shapes and performance are measured using a sail dynamometer boat Fujin. The Fujin is a 34-foot LOA boat, in which load cells and charge coupled devices (CCD) cameras are installed to measure the sail forces and shapes simultaneously. The sailing conditions of the boat, such as boat speed, heel angle, wind speed, wind angle, and so on, are also measured. The tested sail configurations are as follows: mainsail with 130% jib, mainsail with 75% jib and mainsail alone. Sail shapes are measured at several height positions. The measured shape parameters are chord length, maximum draft, maximum draft position, entry angle at the luff and exit angle at the leech. From these parameters three-dimensional coordinates of the sails are calculated by interpolation. These three-dimensional coordinates are tabulated with the aerodynamic coefficients. Numerical calculations are performed using the measured sail shapes. The calculation methods are of two types; Reynolds-averaged Navier-Stokes (RANS)-based CFD and vortex lattice methods (VLM). A multi-block RANS-based CFD method was developed by one of the authors and is capable of predicting viscous flows and aerodynamic forces for complicated sail configuration for upwind as well as downwind conditions. Important features of the numerical method are summarized as follows: a Finite- Analytic scheme to discretize transport equations, a PISO type velocity-pressure coupling scheme, multi-block domain decomposition capability, and several choices of turbulence models depending on flows of interest. An automatic grid generation scheme is also included. Another calculation method, the vortex lattice method is also adopted. In this case, step-by-step calculations are conducted to attain the steady state of the sail in steady wind. Wake vortices are generated step-by-step, which flow in the direction of the local velocity vector. These calculated sail forces are compared with the measured one, and the validity of the numerical method is studied. The sail shape database and comparison with numerical calculations will provide a good benchmark for the sail performance analysis of the upwind condition of IMS type sails.

scholarly journals A Review of Passive Micromixers with a Comparative Analysis

Micromachines ◽  
2020 ◽  
Vol 11 (5) ◽  
pp. 455 ◽  
Author(s):  
Wasim Raza ◽  
Shakhawat Hossain ◽  
Kwang-Yong Kim
Keyword(s):  
Reynolds Number ◽  
Comparative Analysis ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Number Range ◽  
Pressure Drops ◽  
Convection Diffusion ◽  
Wide Range ◽  
Quantitative Analyses ◽  
Mixing Costs

A wide range of existing passive micromixers are reviewed, and quantitative analyses of ten typical passive micromixers were performed to compare their mixing indices, pressure drops, and mixing costs under the same axial length and flow conditions across a wide Reynolds number range of 0.01–120. The tested micromixers were selected from five types of micromixer designs. The analyses of flow and mixing were performed using continuity, Navier-Stokes and convection-diffusion equations. The results of the comparative analysis were presented for three different Reynolds number ranges: low-Re (Re ≤ 1), intermediate-Re (1 < Re ≤ 40), and high-Re (Re > 40) ranges, where the mixing mechanisms are different. The results show a two-dimensional micromixer of Tesla structure is recommended in the intermediate- and high-Re ranges, while two three-dimensional micromixers with two layers are recommended in the low-Re range due to their excellent mixing performance.

Simulation of the Interaction of Labyrinth Seal Leakage Flow and Main Flow in an Axial Turbine

2002 ◽  
Author(s):  
Jan E. Anker ◽  
Ju¨rgen F. Mayer
Keyword(s):  
Experimental Data ◽  
Labyrinth Seal ◽  
Main Flow ◽  
Rotor Blades ◽  
Navier Stokes ◽  
Test Case ◽  
Leakage Flow ◽  
Computational Results ◽  
Axial Turbine ◽  
The Impact

This paper presents the simulation of the flow in a 1.5 stage low-speed axial turbine with shrouded rotor blades and focuses on the interaction of the labyrinth seal leakage flow with the main flow. The presented results were obtained using the Navier-Stokes code ITSM3D developed at University of Stuttgart. A comparison of the computational results with experimental data of this test case gained at Ruhr-Universita¨t Bochum verifies that the flow solver is capable of reproducing the leakage flow effects to a sufficient extent. The computational results are used to examine the influence of the leakage flow on the flow field of the turbine. By varying the clearance height of the labyrinth in the simulations, the impact of the re-entering leakage flow on the main flow is studied. As demonstrated in this paper, leakage flow not only introduces mixing losses but can also dominate the secondary flow and induce severe losses. In agreement with the experimental data the computational results show that at realistic clearance heights the leakage flow gives rise to negative incidence over a considerable part of the downstream stator which causes the flow to separate.

Numerical Simulation of Thermo-Electro-Magnetic Performances in Supersonic Channel Flow

2006 ◽  
Author(s):  
Z. Xu ◽  
C. Lee ◽  
R. S. Amano
Keyword(s):  
Channel Flow ◽  
Gas Flow ◽  
Mhd Flow ◽  
Navier Stokes ◽  
Test Case ◽  
Splitting Algorithm ◽  
Square Duct ◽  
Mhd Generator ◽  
Electro Magnetic ◽  
Applied Fields

A compressible magnetohydrodynamic (MHD) model composed of MHD Navier-Stokes (N-S) equations and magnetic induction equations is proposed in the present study for analyzing the magnetohydrodynamic characteristics in MHD generator and MHD accelerator channels of Magneto-Plasma-Chemical propulsion system [10∼12]. A splitting algorithm based on an alternative iteration is also developed for solving the two sets of equations [9]. As a test case, a supersonic MHD flow in a square duct was simulated. The numerical results are compared with the results computed by solving the classical N-S equations for the perfect gas flow, together with the results computed utilizing the degenerate MHD N-S equations for the same channel flow with constant applied magnetic field. The thermo-electro-magnetic performances of the test cases with constant and variable applied fields are then discussed.

Sign in / Sign up

Export Citation Format

Share Document