Design, Build and Testing of a Noise-Free Twin Shaft Co-Axial Wind Turbine for UTS Buildings

2012 ◽  
Vol 452-453 ◽  
pp. 1089-1093
Author(s):  
Jafar Madadnia ◽  
Deepak Kala ◽  
Dheerej Pillai ◽  
Homa Koosha
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Urban Areas ◽  
Noise Analysis ◽  
Noise Pollution ◽  
Aerodynamic Noise ◽  
Bench Mark ◽  
Horizontal Axis Wind Turbine ◽  
Scaled Model ◽  
And Control

Management and control of noise pollution in wind turbines are important to integrate wind turbines in building and urban areas. A scaled model of a horizontal-co-axial wind turbine was designed, built and tested in the wind tunnel of University of Technology Sydney (UTS) and its characteristics and aerodynamic-noise emissions were analyzed. The noise reduction capability of the horizontal-twin-shaft wind turbines was compared with wind turbines with the conical entry nozzle (stator), duct-shroud-envelop and vertical shafts. Air velocity, shaft rpm, electric-power generation, noise frequency and amplitude were measured. It was found that up to 15% reduction in the amplitude (dB) of noise emisit from twin shaft wind turbine compared to the single shaft bench mark turbine. The noise analysis performed as a result of these experiments may be used in the design and selection of a building integrated horizontal axis wind turbine for applications at UTS buildings.

scholarly journals Fabrication and Performance Evaluation of Savonious Vertical Axis Wind Turbine for Uncertain Speed Regions

2017 ◽  
Vol 13 (2) ◽  
Keyword(s):  
Performance Evaluation ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Urban Areas ◽  
Vertical Axis ◽  
Design Parameters ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
And Performance

The consumption of electricity in urban as well as rural is increasing every day and became an essential commodity for household and industrial purposes. Unfortunately the availability of electrical energy in India is not sufficient to the required demand and it is essential to discover and generate energy from non-conventional sources with cheap cost. On the same time it is necessary to reduce the consumption of conventional sources and to save fuel. Among all the renewable resources, wind is one of the best resources available all the time at free of cost. Especially vertical axis wind turbines (VAWT) are self-starting, omni directional. They require no yaw mechanism to continuously orient towards the wind direction and provide a more reliable energy conversion technology, as compared to horizontal axis wind turbine. Particularly savonius vertical axis wind turbines (SVAWT) are suitable and practically possible at low or uncertain wind speed regimes. They can be fitted on rooftops and also suitable for the urban areas where electricity is not available properly. This project deals with the fabrication and performance evaluation of savonius vertical axis wind turbine using two blade rotor. The amount of power developed by the wind turbine is calculated under theoretical and practical conditions and aerodynamics coefficients are also estimated. And various design parameters of savonious rotor are identified and determined.

CFD Calculation of Wind Turbines Power Variations in Urban Areas

2012 ◽  
Vol 622-623 ◽  
pp. 1084-1088
Author(s):  
Jafar Bazrafshan ◽  
Payam Sabaeifard ◽  
Farid Khalafi ◽  
Majid Jamil
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Power Output ◽  
Urban Areas ◽  
Stokes Equations ◽  
Horizontal Axis ◽  
Navier Stokes ◽  
Horizontal Axis Wind Turbine ◽  
Navier Stokes Equations ◽  
Cfd Method

Integrating wind turbines in urban areas especially over buildings is a new way of producing electricity which is supported in recent years. Wind turbines sited well above the roof of buildings operate in skewed flow. In this paper, to examine variations in efficiency of wind turbines in this condition, two models of H-Rotor and horizontal axis wind turbine analyzed based on axial momentum theory through computer simulations. Simulations conducted through CFD method and k-ε turbulence model was utilized to analyze flow fluctuations in Navier-Stokes equations. Models show that, for an H-Rotor, the optimal power output in tilted flow can be up to two times the power output of horizontal axis wind turbine (HAWT).

scholarly journals Canard optimization for enhancing the performance of small horizontal axis wind turbine at low wind speeds

2020 ◽  
Vol 37 ◽  
pp. 63-71
Author(s):  
Yui-Chuin Shiah ◽  
Chia Hsiang Chang ◽  
Yu-Jen Chen ◽  
Ankam Vinod Kumar Reddy
Keyword(s):  
Wind Turbine ◽  
Urban Areas ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Peak Performance ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Wind Speeds ◽  
Optimum Parameters ◽  
Low Wind Speeds

ABSTRACT Generally, the environmental wind speeds in urban areas are relatively low due to clustered buildings. At low wind speeds, an aerodynamic stall occurs near the blade roots of a horizontal axis wind turbine (HAWT), leading to decay of the power coefficient. The research targets to design canards with optimal parameters for a small-scale HAWT system operated at variable rotational speeds. The design was to enhance the performance by delaying the aerodynamic stall near blade roots of the HAWT to be operated at low wind speeds. For the optimal design of canards, flow fields of the sample blades with and without canards were both simulated and compared with the experimental data. With the verification of our simulations, Taguchi analyses were performed to seek the optimum parameters of canards. This study revealed that the peak performance of the optimized canard system operated at 540 rpm might be improved by ∼35%.

Study on a global control strategy for rotation speed with different work states in variable-speed constant-frequency wind turbines

2011 ◽  
Vol 225 (7) ◽  
pp. 968-976 ◽  
Author(s):  
G Zheng ◽  
H Xu ◽  
X Wang ◽  
J Zou
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Control Strategy ◽  
Control Strategies ◽  
Stable Operation ◽  
Constant Frequency ◽  
Global Control ◽  
Control Rules ◽  
The Individual ◽  
And Control

This paper studies the operation of wind turbines in terms of three phases: start-up phase, power-generation phase, and shutdown phase. Relationships between the operational phase and control rules for the speed of rotation are derived for each of these phases. Taking into account the characteristics of the control strategies in the different operational phases, a global control strategy is designed to ensure the stable operation of the wind turbine in all phases. The results of simulations are presented that indicate that the proposed algorithm can control the individual phases when considered in isolation and also when they are considered in combination. Thus, a global control strategy for a wind turbine that is based on a single algorithm is presented which could have significant implications on the control and use of wind turbines.

scholarly journals Foundations, Design, and Dynamic Performance of Wind Turbines: Overview and Challenges in Sudan

2021 ◽  
Vol 9 (1) ◽  
pp. 96-103
Author(s):  
Ruba Asim Hamza ◽  
Amged Osman Abdelatif
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Structural Damage ◽  
Renewable Energy Sources ◽  
Dynamic Performance ◽  
Scaled Model ◽  
Static Loads ◽  
Design Loads ◽  
Foundation Type

Sudan is one of the developing countries that suffers from a lack of electricity, where the national electrification rate is estimated at 38.5%. In order to solve this problem, it is possible to use renewable energy sources such as wind energy. Beside many aspects to be considered at the design of wind turbine foundations, more attention should be given to the geotechnical part. There are many types of foundations for wind turbines. The foundation must satisfy two design criteria: 1) It should be safe against bearing failure in soils under design loads and settlements during the life of the structure must not cause structural damage; 2) In addition to static loads, wind turbine foundations loads are extremely eccentrically and the loading is usually highly dynamic. Therefore, the selection of foundation type should consider these two criteria taking into account the nature and magnitude of these loads. This paper presents a review of different types of wind turbine foundations of focusing on on-shore wind turbine foundation types and the dynamic response of wind turbine. The paper also demonstrate experimentally the dynamic response of the wind turbines using wind tunnel facility test on a scaled model.  

scholarly journals Modeling and simulation of forces applied to the horizontal axis wind turbine rotors by the vortex method coupled with the method of the blade element

2021 ◽  
Vol 12 (1) ◽  
pp. 413
Author(s):  
Ibtissem Barkat ◽  
Abdelouahab Benretem ◽  
Fawaz Massouh ◽  
Issam Meghlaoui ◽  
Ahlem Chebel
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Farms ◽  
Vortex Method ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Rotor Blades ◽  
Good Representation ◽  
Horizontal Axis Wind Turbine ◽  
Blade Element

This article aims to study the forces applied to the rotors of horizontal axis wind turbines. The aerodynamics of a turbine are controlled by the flow around the rotor, or estimate of air charges on the rotor blades under various operating conditions and their relation to the structural dynamics of the rotor are critical for design. One of the major challenges in wind turbine aerodynamics is to predict the forces on the blade as various methods, including blade element moment theory (BEM), the approach that is naturally adapted to the simulation of the aerodynamics of wind turbines and the dynamic and models (CFD) that describes with fidelity the flow around the rotor. In our article we proposed a modeling method and a simulation of the forces applied to the horizontal axis wind rotors turbines using the application of the blade elements method to model the rotor and the vortex method of free wake modeling in order to develop a rotor model, which can be used to study wind farms. This model is intended to speed up the calculation, guaranteeing a good representation of the aerodynamic loads exerted by the wind.

Model Identification and Operating Load Characterization for a Small Horizontal Axis Wind Turbine Rotor Using Integrated Blade Sensors

2010 ◽  
Author(s):  
Scott Dana ◽  
Joseph Yutzy ◽  
Douglas E. Adams
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Rotor Blade ◽  
Model Identification ◽  
Turbine Rotor ◽  
Forced Response ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
And Control ◽  
Wind Turbine Rotor

One of the primary challenges in diagnostic health monitoring and control of wind turbines is compensating for the variable nature of wind loads. Given the sometimes large variations in wind speed, direction, and other operational variables (like wind shear), this paper proposes a data-driven, online rotor model identification approach. A 2 m diameter horizontal axis wind turbine rotor is first tested using experimental modal analysis techniques. Through the use of the Complex Mode Indication Function, the dominant natural frequencies and mode shapes of dynamic response of the rotor are estimated (including repeated and pseudo-repeated roots). The free dynamic response properties of the stationary rotor are compared to the forced response of the operational rotor while it is being subjected to wind and rotordynamic loads. It is demonstrated that both narrowband (rotordynamic) and broadband (wind driven) responses are amplified near resonant frequencies of the rotor. Blade loads in the flap direction of the rotor are also estimated through matrix inversion for a simulated set of rotor blade input forces and for the operational loading state of the wind turbine in a steady state condition. The analytical estimates are shown to be accurate at frequencies for which the ordinary coherence functions are near unity. The loads in operation are shown to be largest at points mid-way along the span of the blade and on one of the three blades suggesting this method could be used for usage monitoring. Based on these results, it is proposed that a measurement of upstream wind velocity will provide enhanced models for diagnostics and control by providing a leading indicator of disturbances in the loads.

Experimental Study of Aerodynamic Noise From the Trailing Edge and Leading Edge of Blades in a Coaxial-Double Shaft Fan

2013 ◽  
Author(s):  
Jafar Madadnia ◽  
Mustafa Shekeb ◽  
Thimantha Ulluwishewa
Keyword(s):  
Wind Turbines ◽  
Acoustic Noise ◽  
Residential Building ◽  
Leading Edge ◽  
Noise Pollution ◽  
Aerodynamic Noise ◽  
Trailing Edge ◽  
Double Row ◽  
Positive Effects ◽  
Spacing Variation

Proactive acoustic noise control technologies in wind turbines and blowers have in recent years been the focus of intensive research to integrate wind turbines in residential building and to address public concerns on noise pollution. However efforts to understand the mechanics has been inconclusive, mainly due to the complexity and commercial confidentiality of the topic. The paper reports on the experimental investigation on two methods in controlling aerodynamic noise. A counter-rotating-double-row-turbine with variable gap/spacing (s) was designed, built and tested. Serrations were designed and attached on the leading edge and the trailing edge of the blades to proactively control aerodynamic noise. The model was operated in fan-mode and air velocity, shaft-revolution; electric-fan-power, acoustic noise amplitude (dB) and Centre frequency (CF in Hz) were measured for a number of spacing and serrations. Coefficients of Performance (COP), dB, CF were plotted against tip speed (TS). It was noticed that: • The double-shaft-fan has operated quieter than the single shaft fan especially as TS decreases. Acoustic noise (dB) dropped 20% at TS = 4m/s to less than 2% at TS = 10m/s. Efficiency and CF increased in the double-shaft fan as TS increased. Spacing variation between blade-rows had insignificant effect on the dB, Cf, and efficiency. • Serrations on single-shaft fan have also reduced dB (up to 10%), increased efficiency and CF with more positive effects with the serrations on the leading edge than the trailing edge. Serrations are more effective at higher TS range. • Serrations on a double-shaft fan with an optimum spacing, reduced acoustic noise (dB) only allow speeds [at TS <4m/s]. However minor improvement was noticed in efficiency or noise frequency.

Nondimensional Parameters’ Effects on Hybrid Darrieus–Savonius Wind Turbine Performance

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Armin Roshan ◽  
Amir Sagharichi ◽  
Mohammad Javad Maghrebi
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Power Output ◽  
Urban Areas ◽  
Model Performance ◽  
Vertical Axis ◽  
Favorable Effect ◽  
Turbine Performance ◽  
Primary Model ◽  
Overlap Ratio

Abstract Vertical axial wind turbines are the most commonly used turbines in residential and urban areas. This paper investigates the effect of combining Darrieus and Savonius wind turbines on power output and introduces a wind turbine with high starting torque addition to the wide working domain. A two-dimensional computational fluid dynamics transient simulation is developed, and a moving mesh is implemented for rotating moving parts. Comprehensive research has been carried out to investigate the effects of the initial overlap ratio (ɛ), arc angle Ø, and curvature (α) of Savonius blades on the performance of the turbine and 18 models are simulated at seven tip speed ratios. The results showed that combining the Darrieus turbine with the Savonius turbine has a favorable effect on self-starting performance. Also, it was observed that by changing each of the parameters, the primary model performance could be significantly improved. Finally, it is concluded that ɛ = 0.25, α = 0.25, and ∅ = 150 deg are the optimum values of the parameters which increase turbine power output compared to conventional vertical-axis turbines.

scholarly journals Comparison of horizontal axis wind turbine (HAWT) and vertical axis wind turbine (VAWT)

2018 ◽  
Vol 7 (4.13) ◽  
pp. 74 ◽  
Author(s):  
Muhd Khudri Johari ◽  
Muhammad Azim A Jalil ◽  
Mohammad Faizal Mohd Shariff
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Green Technology ◽  
Horizontal Axis ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine ◽  
Current Output ◽  
Voltage Output ◽  
And Performance

As the demand for green technology is rising rapidly worldwide, it is important that Malaysian researchers take advantage of Malaysia’s windy climates and areas to initiate more power generation projects using wind. The main objectives of this study are to build a functional wind turbine and to compare the performance of two types of design for wind turbine under different speeds and behaviours of the wind. A three-blade horizontal axis wind turbine (HAWT) and a Darrieus-type vertical axis wind turbine (VAWT) have been designed with CATIA software and constructed using a 3D-printing method. Both wind turbines have undergone series of tests before the voltage and current output from the wind turbines are collected. The result of the test is used to compare the performance of both wind turbines that will imply which design has the best efficiency and performance for Malaysia’s tropical climate. While HAWT can generate higher voltage (up to 8.99 V at one point), it decreases back to 0 V when the wind angle changes. VAWT, however, can generate lower voltage (1.4 V) but changes in the wind angle does not affect its voltage output at all. The analysis has proven that VAWT is significantly more efficient to be built and utilized for Malaysia’s tropical and windy climates. This is also an initiative project to gauge the possibility of building wind turbines, which could be built on the extensive and windy areas surrounding Malaysian airports.  

Sign in / Sign up

Export Citation Format

Share Document