Wear Performance of the Plasma Sprayed Fine WC-Co Composite Powders Coatings

2012 ◽  
Vol 454 ◽  
pp. 144-147
Author(s):  
Lian Wei Yang ◽  
Jin Hui Li ◽  
Yun Dong ◽  
Xiao Ping Lin
Keyword(s):  
Wear Resistance ◽  
Brittle Fracture ◽  
Composite Coating ◽  
Plasma Spraying ◽  
Composite Coatings ◽  
Composite Powders ◽  
Wear Performance ◽  
Wear And Friction ◽  
Plasma Sprayed ◽  
Increasing Load

WC/Co; Composite coating; Plasma spraying; Friction and wear Abstract: WC- Co composite powders were synthesized by direct mechanical grinding in a rotary-vibration mill under 8h, and then analyzed by SEM and XRD. WC and WC/Co composite coatings were prepared by supersonic plasma spraying fine WC-Co composite powders. The wear and friction properties of both coatings were evaluated. The results showed that the wear resistance of the WC/Co composite coating was superior to that of the WC coating. The improvement in wear resistance of the WC/Co composite coating was attributed to its higher fracture toughness and adhesion strength as well as better thermal diffusivity. As for the WC/Co composite coating, the mechanism was mainly adhesion with micro-abrasion and fatigued-induced brittle fracture within splats, and the delamination along splat boundaries only occurred at high load. However, the failure of the WC coating was predominantly detachment of transferred film and brittle fracture within the splats and delamination along splat boundaries, which were enhanced with the increasing load.

scholarly journals Phase Transformation-Induced Improvement in Hardness and High-Temperature Wear Resistance of Plasma-Sprayed and Remelted NiCrBSi/WC Coatings

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1688
Author(s):  
Jin Sha ◽  
Liang-Yu Chen ◽  
Yi-Tong Liu ◽  
Zeng-Jian Yao ◽  
Sheng Lu ◽  
...  
Keyword(s):  
Wear Resistance ◽  
High Temperature ◽  
Composite Coating ◽  
Composite Coatings ◽  
Hardness Test ◽  
Wear Volume ◽  
Dispersion Strengthening ◽  
High Temperature Wear ◽  
Nicrbsi Coating ◽  
Plasma Sprayed

The remelting method is introduced to improve the properties of the as-sprayed NiCrBSi coatings. In this work, tungsten carbide (WC) was selected as reinforcement and the as-sprayed and remelted NiCrBSi/WC composite coatings were investigated by X-ray diffraction, scanning electron microscopy, hardness test and tribology test. After spraying, WC particles are evenly distributed in the coating. The remelting process induced the decarburizing reaction of WC, resulting in the formation of dispersed W2C. The dispersed W2C particles play an important role in the dispersion strengthening. Meanwhile, the pores and lamellar structures are eliminated in the remelted NiCrBSi/WC composite coating. Due to these two advantages, the hardness and the high-temperature wear resistance of the remelted NiCrBSi/WC composite coating are significantly improved compared with those with an as-sprayed NiCrBSi coating; the as-sprayed NiCrBSi coating, as-sprayed NiCrBSi/WC composite coating and remelted NiCrBSi/WC composite coating have average hardness of 673.82, 785.14, 1061.23 HV, and their friction coefficients are 0.3418, 0.3261, 0.2431, respectively. The wear volume of the remelted NiCrBSi/WC composite coating is only one-third of that of the as-sprayed NiCrBSi coating.

The Manufacture of SiC Fiber Reinforced ΑI2O3 Coatings by Plasma Spraying

1996 ◽  
Author(s):  
H.-D. Steffens ◽  
M. Brune ◽  
E. Müller ◽  
R. Dittrich
Keyword(s):  
Plasma Spraying ◽  
Composite Coatings ◽  
High Strength ◽  
Ceramic Coatings ◽  
Ceramic Composites ◽  
Composite Powders ◽  
Pure Alumina ◽  
High Oxygen Content ◽  
Sic Fiber ◽  
Plasma Sprayed

Abstract Oftentimes, the application of bulk ceramics and ceramic coatings is limited by their poor fracture toughness and low strength. The mechanical properties of ceramics can be significantly improved by the incorporation of fibres, whiskers or particles of high strength, like SiC. Due to the high oxygen content of commercially available SiC fibers in combination with the elevated process temperatures, the SiC decomposes during plasma spraying. Therefore commercial SiC fibres were coated for temporary oxidation protection with C, TiN or Al2O3. By different agglomeration techniques using an organic binder SiC/Al2O3 composite powders were produced. Powder mixtures consisting of coated fibres and pure alumina as well as agglomerated powders have been successfully sprayed to form deposits. Recent results of the manufacture of SiC fibre-reinforced ceramic composites by plasma spray technology are presented. The properties of the composite coatings are compared to plasma sprayed pure alumina.

Tribological Properties of Plasma Sprayed Self-Lubricating NiCr/Cr3C2-BN Composite Coatings

2011 ◽  
Vol 675-677 ◽  
pp. 1245-1248
Author(s):  
Chuan Bing Huang ◽  
Ling Zhong Du ◽  
Wei Gang Zhang
Keyword(s):  
Wear Resistance ◽  
Friction Coefficient ◽  
Tribological Properties ◽  
Adhesive Strength ◽  
Composite Coatings ◽  
Composite Powders ◽  
Mechanical And Tribological Properties ◽  
Plasma Sprayed ◽  
Spray Granulation ◽  
High Adhesive Strength

In this study, two kinds of NiCr/Cr3C2-BN composite powders were prepared with individual cladding (FKBN) and low pressure spray granulation (YLBN) methods, and the derived NiCr/Cr3C2-BN coatings were fabricated by plasma spraying technology. The microstructure, mechanical and tribological properties of the two coatings were systematically investigated. Both NiCr/Cr3C2-BN coatings have relatively high adhesive strength and microhardness, but the porosity of YLBN coating is much lower than that of FKBN coating. With comparison to FKBN coating, YLBN coating showed lower friction coefficient and better wear resistance, which was attributed to the more compact microstructure and uniform distribution of BN in the coating.

Evaluation of Slurry Erosive Wear Performance of Plasma-Sprayed Flyash-TiO2 Composite Coatings

2021 ◽  
Vol 7 (3) ◽  
Author(s):  
R. Keshavamurthy ◽  
B. E. Naveena ◽  
C. S. Ramesh ◽  
M. R. Haseebuddin
Keyword(s):  
Composite Coatings ◽  
Erosive Wear ◽  
Wear Performance ◽  
Plasma Sprayed

Laser Sintering of Nano-Al2O3 Powders on Plasma Sprayed Ceramic Based Coatings

2007 ◽  
Author(s):  
Lida Shen ◽  
Yinhui Huang ◽  
Zongjun Tian ◽  
Guoran Hua
Keyword(s):  
Wear Resistance ◽  
Corrosion Resistance ◽  
Plasma Spraying ◽  
Bond Coat ◽  
Continuous Wave ◽  
Ceramic Coatings ◽  
Laser Sintering ◽  
Al2o3 Ceramic ◽  
Plasma Sprayed ◽  
Steel Substrates

This paper describes an investigation of nano-Al2O3 powders reinforced ceramic coatings, which has included NiCrAl and Al2O3+13%wt.TiO2 coats pre-produced by atmosphere plasma spraying, implemented by laser sintering. Commercial NiCrAl powders were plasma sprayed onto 45 Steel substrates to give a bond coat with thickness of ∼100μm. The 600μm thick Al2O3+13%wt.TiO2 based coating was also plasma sprayed on top of the NiCrAl bond coat. With 2.5kw continuous wave CO2 laser, nano-Al2O3 ceramic powders were laser sintered on the based Coatings. The micro structure and chemical composition of the modified Al2O3+13%wt.TiO2 coatings were analyzed by such detection devices as scanning electronic microscope (SEM) and x-ray diffraction (XRD). Microhardness, wear resistance and corrosion resistance of the modified coatings were also tested and compared with that of the unmodified. The results show that the crystal grain size of Al2O3 had no obvious growth. In addition, due to the nanostructured Al2O3 ceramic phases, the coatings exhibited higher microhardness, better wear resistance and corrosion resistance than those unmodified counterparts. The complex process of plasma spraying with laser sintering as a potential effective way of the application of ceramic nano materials was also simply discussed and summarized in the end.

Microstructural characteristics of SiC-B4C reinforced laser alloying composite coatings

2013 ◽  
Vol 20 (4) ◽  
pp. 307-310
Author(s):  
Li Wei
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Fine Particles ◽  
Composite Coatings ◽  
Substrate Surface ◽  
Laser Alloying ◽  
Wear Process ◽  
High Microhardness ◽  
Deep Plowing ◽  
Coating Matrix

AbstractA hard SiC-B4C reinforced composite coating was fabricated by laser alloying of SiC-B4C+Al-Sn-Mo-Y2O3 mixed powders on a Ti-3Al-2V alloy. Al-Sn-Mo mixed powders were first used in the laser alloying technique to improve the wear resistance of titanium alloys. Proper selection of the laser alloying process parameters allows us to obtain a composite coating with a metallurgical combination with substrate. Under the action of Mo, fine particles with high microhardness were produced in the coating matrix and also hindered the formation of adhesion patches and deep plowing grooves during the sliding wear process, leading to the improvement of wear resistance of a titanium alloy substrate surface.

Study on the Wear Resistance of Micro-Nanostructured WC Composite Coating Sintered by Induced Heating

2007 ◽  
Vol 280-283 ◽  
pp. 1489-1492
Author(s):  
Zhen Ting Wang ◽  
Hua Hui Chen
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Solid Solutions ◽  
Composite Coatings ◽  
Micro Hardness ◽  
Q235 Steel ◽  
Metallurgical Bonding ◽  
Sintering Method

Micro-nanostructured WC composite coatings were successfully fabricated by induced heating sintering method on the surface of Q235 steel .The microstructure, micro-hardness and the wear resistance of the composite coatings were studied .The results show that the microstructure of induced heat layer is mainly composed of Ni-based solid solutions and WC particles. And there exists excellent metallurgical bonding between coating and substrate. The wear resistance of micro-nanostructured WC Composite Coatings is increased by 1.5 times on an average as compared with that of micron.

In situ composite coatings prepared by complex reactive plasma spraying of Fe 2 O 3 -Al-Cr 2 O 3 composite powders

2017 ◽  
Vol 328 ◽  
pp. 94-101 ◽  
Author(s):  
Dian-ran Yan ◽  
Yong Yang ◽  
Zhen-hua Chu ◽  
Xue-guang Chen ◽  
Xue-rui Dai ◽  
...  
Keyword(s):  
Plasma Spraying ◽  
Composite Coatings ◽  
Composite Powders ◽  
In Situ Composite ◽  
Reactive Plasma Spraying ◽  
Reactive Plasma

scholarly journals Laser Cladding of Ni-Co-W Composite Coating on Stainless Steel to Enhance Wear Resistance

2021 ◽  
Author(s):  
Linlin ZHANG ◽  
Dawei ZHANG
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Composite Coating ◽  
Laser Cladding ◽  
Composite Coatings ◽  
Eutectic Structure ◽  
Wear Properties ◽  
Fine Grained ◽  
Noticeable Improvement ◽  
Enhance Wear Resistance

Ni-Co-W composite coatings modified by different contents of Co-based alloy powder in the Ni-based alloy with 35 wt.% WC (Ni35WC) were deposited on stainless steel by laser cladding. The influence of compositional and microstructural modification on the wear properties has been comparatively investigated by XRD, SEM, and EDS techniques. It was found that the austenite dendrites in the modified coating adding 50 wt.% Co-based alloy were refined and a lot of Cr23C6 or M23(C, B)6 compounds with fine lamellar feature were formed around austenitic grain boundaries or in the intergranular regions. The contribution of element Co to the modification of Ni35WC coating is that it cannot only promote the formation of more hard compounds to refine austenite grains, but also refine the size of precipitates, and change the phase type of eutectic structure as a result of disappeared Cr boride brittle phases. A noticeable improvement in wear resistance is obtained in the Ni35WC coating with 50 wt.% Co-based alloy, which makes the wear rate decreased by about 53 % and 30% by comparison to that of the substrate and the Ni35WC coating, respectively. It is suggested that the improvement is closely related to the composite coating being strengthened owing to the increase of coating hardness, formation of a fine-grained microstructure caused by Co, and fine hard precipitate phases in the eutectic structure.

Sign in / Sign up

Export Citation Format

Share Document