Study on the Wear Resistance of Micro-Nanostructured WC Composite Coating Sintered by Induced Heating

2007 ◽  
Vol 280-283 ◽  
pp. 1489-1492
Author(s):  
Zhen Ting Wang ◽  
Hua Hui Chen
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Solid Solutions ◽  
Composite Coatings ◽  
Micro Hardness ◽  
Q235 Steel ◽  
Metallurgical Bonding ◽  
Sintering Method

Micro-nanostructured WC composite coatings were successfully fabricated by induced heating sintering method on the surface of Q235 steel .The microstructure, micro-hardness and the wear resistance of the composite coatings were studied .The results show that the microstructure of induced heat layer is mainly composed of Ni-based solid solutions and WC particles. And there exists excellent metallurgical bonding between coating and substrate. The wear resistance of micro-nanostructured WC Composite Coatings is increased by 1.5 times on an average as compared with that of micron.

Characteristics of Laser Cladded Nickel-Based Chromic Carbide Composite Coatings

2017 ◽  
Vol 893 ◽  
pp. 340-344
Author(s):  
Sheng Dai ◽  
Dun Wen Zuo ◽  
Xian Rui Zhao ◽  
Jin Fang Wang
Keyword(s):  
Wear Resistance ◽  
Carbon Steel ◽  
Composite Coating ◽  
Steel Substrate ◽  
Composite Coatings ◽  
Surface Hardness ◽  
Micro Hardness ◽  
Wear Properties ◽  
Hardness Tester ◽  
Metallurgical Bonding

To improve the surface hardness and wear resistance of metal parts. Ni-based chromic carbidecomposite coating was prepared on the carbon steel (0.45 mass% C) substrates by laser cladding. Microstructure and wear properties of composite coatings were investigated by SEM, EDS, XRD, Vickers micro-hardness tester and wear machine. The results show that good metallurgical bonding between the Ni-based chromic carbidecomposite coating and carbon steel substrate. Micro-hardness of Ni-based Cr3C2 composite coating along the layer depth presents an evident stepladder distribution. The average micro-hardness of the laser clad coating is about 950 HV. The result of wear experiment shows that Ni-based Cr3C2 composite coating processes good wear resistance.

SURFACE PROPERTIES OF THE IN SITU FORMED CERAMICS REINFORCED COMPOSITE COATINGS ON TI-3AL-2V ALLOYS

2012 ◽  
Vol 19 (02) ◽  
pp. 1250009 ◽  
Author(s):  
PENG LIU ◽  
WEI GUO ◽  
DAKUI HU ◽  
HUI LUO ◽  
YUANBIN ZHANG
Keyword(s):  
Wear Resistance ◽  
Titanium Alloy ◽  
Composite Coating ◽  
Surface Properties ◽  
Laser Cladding ◽  
Composite Coatings ◽  
Micro Hardness ◽  
Reinforced Composite

The synthesis of hard composite coating on titanium alloy by laser cladding of Al/Fe/Ni+C/Si3N4 pre-placed powders has been investigated in detail. SEM result indicated that a composite coating with metallurgical joint to the substrate was formed. XRD result indicated that the composite coating mainly consisted of γ- (Fe, Ni) , FeAl , Ti3Al , TiC , TiNi , TiC0.3N0.7 , Ti2N , SiC , Ti5Si3 and TiNi . Compared with Ti-3Al-2V substrate, an improvement of the micro-hardness and the wear resistance was observed for this composite coating.

scholarly journals Microstructure and Wear Behavior of In-Situ NbC Reinforced Composite Coatings

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3459 ◽  
Author(s):  
Baoming Shi ◽  
Shiming Huang ◽  
Ping Zhu ◽  
Changen Xu ◽  
Tengfei Zhang
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Wear Behavior ◽  
Composite Coatings ◽  
Niobium Carbide ◽  
Low Carbon Steel ◽  
High Hardness ◽  
Low Carbon ◽  
Micro Hardness

In the present study, plasma spray welding was used to prepare an in-situ niobium carbide (NbC) reinforced Ni-based composite coating on the low carbon steel, and the phase composition and the microstructure of the composite coatings were studied. The wear resistance and the wear mechanism of the composite coatings were also researched by the wear tests. The results showed that the main phases of the composite coating were NbC, γ-Ni, Cr23C6, Ni3Si, CrB, Cr5B3, Cr7C3 and FeNi3. A number of fine in-situ NbC particles and numerous chromium carbide particles were distributed in the γ-Ni matrix. The increase in the mass fraction of Nb and NiCr-Cr3C2 could lead to the increase in NbC particles in the composite coatings. Due to the high hardness of NbC and chromium carbides, the micro-hardness and the wear resistance of the composite coatings were advanced. The composite coating with the powder mixtures of 20% (Nb + NiCr-Cr3C2) and 80% NiCrBSi had the highest micro-hardness and the best wear resistance in this study. The average micro-hardness reached the maximum value 1025HV0.5. The volume loss was 39.2 mm3, which was merely 37% of that of the NiCrBSi coating and 6% of that of the substrate under the identical conditions.

Microstructure and Wear Resistance of Nanostructure WC Composite Coatings Prepared by Argon Arc Cladding Injection

2014 ◽  
Vol 1082 ◽  
pp. 480-483
Author(s):  
Zhen Ting Wang ◽  
Shi Kui Zhu ◽  
Fan Feng ◽  
Hao Ran Cheng ◽  
Zhi Jie Kang ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Composite Coatings ◽  
Energy Dispersive Spectrometer ◽  
Testing Machine ◽  
Wear Testing ◽  
Maximum Hardness ◽  
X Ray ◽  
Q235 Steel ◽  
Metallurgical Bonding ◽  
Bonding Area

Nanostructure WC composite coatings were prepared on surface of Q235 steel by argon arc cladding injection using microstructure WC feeding which were prepared by nanostructure WC powder. The microstructure of the coating were analyzed by scanning electron microscopy (SEM). Phase of the coating were analyzed by energy dispersive spectrometer and X-Ray diffract meter, moreover, microhardness and wear resistance were texted by Microhardness tester (HVST-1000) and friction wear testing machine (MMS-2A). The results show that the combination of coating and substrate is metallurgical bonding. and no Pores and cracks were founded in bonding area. aggregated nanostructure WC particles and nanostructure WC particles uniformly distributed in the coating. The maximum hardness of the coating is 1461 HV. Compared with the Q235 steel, the wear resistance of the coating increased about 15 times.

A Hard and Thick Fe-Based Amorphous Composite Coating

2011 ◽  
Vol 189-193 ◽  
pp. 858-862 ◽  
Author(s):  
Wei Qiang Hu ◽  
Zong De Liu ◽  
Guang Yang ◽  
Yong Tian Wang ◽  
Hua Lei Zhang
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Composite Coatings ◽  
Cement Industry ◽  
Inert Gas ◽  
Shell Layer ◽  
Micro Hardness ◽  
Materials Used ◽  
Nanocrystalline Composite

A thick Fe-based amorphous and nanocrystalline composite coating was prepared by in-situ tungsten inert gas (TIG) cladding method. The results show that the cladding coating mainly consists of amorphous phase and nanocrystalline grains. The microstructure study shows that the Fe-based composite coatings have unique microstructure including nano-sized grains surrounded by nano-scale amorphous shell layer (encapsulated structure) and the homogeneously distributed dendrites/cellular crystals. The unique microstructure gives rise to the superior micro-hardness and wear resistance of the coating. The Fe-based coatings have great potential as promising wear-resistance structural materials used in electric power and cement industry.

Preparation and Tribological Behavior of Ni-P-B4C Electroless Coatings

2014 ◽  
Vol 809-810 ◽  
pp. 615-620
Author(s):  
Ying Wang ◽  
Wan Chang Sun ◽  
Hui Cai ◽  
Qing Hao Yang ◽  
Ju Mei Zhang
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Tribological Behavior ◽  
Composite Coatings ◽  
Micro Hardness ◽  
Wear Weight Loss ◽  
Heat Treated ◽  
Electroless Coatings ◽  
Electroless Ni ◽  
Minimum Wear

In this research, micro-hardness and wear resistance of two types of electroless coatings were investigated including Ni-P and Ni-P-B4C composite coatings. Dispersible B4C particles and electroless Ni-P alloy were codeposited on carbon steel by electroless plating and then heat treated at 200, 400 and 600 °C for 1 h, respectively. The cross-section morphology and microstructure of the composite coatings were characterized. Meanwhile, the micro-hardness and tribological behavior of composite coatings were evaluated. The results showed that the Ni-P-B4C composite coating presents better wear resistance in comparison with that of Ni-P coating. The Ni-P-B4C composite coating with heat treated at 400 °C exhibits high micro-hardness and good wear resistance, which the highest hardness is 1200 HV, the minimum wear weight loss is 0.12 mg and the lowest friction coefficient is 0.2054.

scholarly journals Surface modification of Ti alloys with WC-TiB2-reinforced laser composite coatings

2016 ◽  
Vol 23 (6) ◽  
pp. 737-741
Author(s):  
Jianing Li ◽  
Yuanbin Zhang ◽  
Hui Luo ◽  
Shuili Gong ◽  
Peng Li ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Amorphous Alloys ◽  
Composite Coatings ◽  
Stabilized Zirconia ◽  
Reinforced Composite ◽  
Ti Alloys ◽  
Metallurgical Bonding ◽  
Fine Microstructure ◽  
Yttria Partially Stabilized Zirconia

AbstractLaser cladding of the TiAl/Fe+Co-coated WC+TiB2 pre-placed mixed powders on a Ti-6Al-4V alloy substrate can be used to form TiB2/α-W2C-reinforced composite coating, which improved the wear resistance of the substrate. To further improve the TiB2/α-W2C-reinforced composite coating, yttria partially stabilized zirconia (YPSZ) was added into the pre-placed powders. A metallurgical bonding was formed between the YPSZ-infused composite coating and the substrate. Many amorphous alloys were produced in this composite coating due to the action of YPSZ, and such coating showed fine microstructure. Thus, it is feasible to further improve the wear resistance of the laser clad TiB2/α-W2C-reinforced composite coating through the addition of YPSZ.

Microstructural characteristics of SiC-B4C reinforced laser alloying composite coatings

2013 ◽  
Vol 20 (4) ◽  
pp. 307-310
Author(s):  
Li Wei
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Fine Particles ◽  
Composite Coatings ◽  
Substrate Surface ◽  
Laser Alloying ◽  
Wear Process ◽  
High Microhardness ◽  
Deep Plowing ◽  
Coating Matrix

AbstractA hard SiC-B4C reinforced composite coating was fabricated by laser alloying of SiC-B4C+Al-Sn-Mo-Y2O3 mixed powders on a Ti-3Al-2V alloy. Al-Sn-Mo mixed powders were first used in the laser alloying technique to improve the wear resistance of titanium alloys. Proper selection of the laser alloying process parameters allows us to obtain a composite coating with a metallurgical combination with substrate. Under the action of Mo, fine particles with high microhardness were produced in the coating matrix and also hindered the formation of adhesion patches and deep plowing grooves during the sliding wear process, leading to the improvement of wear resistance of a titanium alloy substrate surface.

scholarly journals Laser Cladding of Ni-Co-W Composite Coating on Stainless Steel to Enhance Wear Resistance

2021 ◽  
Author(s):  
Linlin ZHANG ◽  
Dawei ZHANG
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Composite Coating ◽  
Laser Cladding ◽  
Composite Coatings ◽  
Eutectic Structure ◽  
Wear Properties ◽  
Fine Grained ◽  
Noticeable Improvement ◽  
Enhance Wear Resistance

Ni-Co-W composite coatings modified by different contents of Co-based alloy powder in the Ni-based alloy with 35 wt.% WC (Ni35WC) were deposited on stainless steel by laser cladding. The influence of compositional and microstructural modification on the wear properties has been comparatively investigated by XRD, SEM, and EDS techniques. It was found that the austenite dendrites in the modified coating adding 50 wt.% Co-based alloy were refined and a lot of Cr23C6 or M23(C, B)6 compounds with fine lamellar feature were formed around austenitic grain boundaries or in the intergranular regions. The contribution of element Co to the modification of Ni35WC coating is that it cannot only promote the formation of more hard compounds to refine austenite grains, but also refine the size of precipitates, and change the phase type of eutectic structure as a result of disappeared Cr boride brittle phases. A noticeable improvement in wear resistance is obtained in the Ni35WC coating with 50 wt.% Co-based alloy, which makes the wear rate decreased by about 53 % and 30% by comparison to that of the substrate and the Ni35WC coating, respectively. It is suggested that the improvement is closely related to the composite coating being strengthened owing to the increase of coating hardness, formation of a fine-grained microstructure caused by Co, and fine hard precipitate phases in the eutectic structure.

MICROSTRUCTURE AND WEAR RESISTANCE OF IN-SITU SYNTHESIZED TiB2–TiC/Fe COMPOSITE COATING BY LASER CLADDING

2020 ◽  
pp. 2050046
Author(s):  
TIANWEI YANG ◽  
ZHAOHUI WANG ◽  
SHIHAI TAN ◽  
FU GUO
Keyword(s):  
Wear Resistance ◽  
Laser Cladding ◽  
Composite Coatings ◽  
X Ray Diffraction ◽  
Mixed Powder ◽  
X Ray ◽  
Material Surfaces ◽  
Metallurgical Bonding ◽  
Steel Surfaces

To increase the strength and wear resistance of material surfaces, various combinations of B4C and 80TiFe powder were mixed into a Fe60 self-fluxing alloy powder; the composite coatings reinforced by TiB2–TiC were successfully prepared on Q235 steel surfaces by laser cladding. Scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) were used to study the microstructure and chemical and phase composition. Microhardness and wear testers were used to investigate the mechanical properties. The results show that the interfaces of composite coatings and substrate materials are excellent for metallurgical bonding. The block-like TiB2 particles and flower-like TiC particles are uniformly distributed in the cladding coating. When the mass fraction of the mixed powder is 30%, the average microhardness of the coating is approximately 1100 HV[Formula: see text], which is 50% higher than that without the mixed powder, and demonstrates the best wear with a performance twice as better as that of the substrate.

Sign in / Sign up

Export Citation Format

Share Document