Preparation, Characterization and Dielectric Properties of BT/PI Film

2012 ◽  
Vol 476-478 ◽  
pp. 819-823
Author(s):  
Jun Jun Lv ◽  
Ming Yu Li ◽  
Qing Xuan Zeng ◽  
Shuang Zhao
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Dielectric Constant ◽  
Composite Film ◽  
Solution Method ◽  
Dielectric Strength ◽  
X Ray Diffraction ◽  
X Ray ◽  
Comprehensive Performance ◽  
Scanning Electron

By using mixture solution method, Barium titanate/polyimide(BT/PI) composite film was prepared. Influence of different size and filling quantity of BT particles were investigated. The microstructure and properties of the products were characterized by scanning electron microscopy, X-ray diffraction and other analysis methods. The results show that when BT nanoparticles are used, the BT/PI film has better comprehensive performance. As the filling quantity of BT particles increases, the dielectric constant and dielectric loss of BT/PI composite film increase, and the dielectric strength is reduced.

Phase Development and Dielectric Properties of 0.98BaTiO3-0.02Ba (Mg1/3Nb2/3) O3 Ceramic

2011 ◽  
Vol 700 ◽  
pp. 58-62
Author(s):  
Rachanusorn Roongtao ◽  
Supagorn Rugmai ◽  
Wanwilai C. Vittayakorn
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Dielectric Constant ◽  
Dielectric Properties ◽  
Loss Factor ◽  
X Ray Diffraction ◽  
Phase Purity ◽  
X Ray ◽  
Phase Development ◽  
Scanning Electron

The 0.98BaTiO3-0.02Ba (Mg1/3Nb2/3) O3ceramics has been synthesized through a conventional mixed-oxide by using BT nanopowder and BMN micropowder. The phase purity of the powders and the ceramics was examined using X-ray diffraction (XRD). The 0.98BT-0.02BMN powders were sintered to 92% of the theoretical density at a temperature of 1300 °C for 2 h. The microstructure of the sintered surface was investigated using scanning electron microscopy (SEM). The dielectric constant (εr) and loss factor (tanδ) of the sintered pellets at Curie temperture were 3000 and 0.015, respectively.

scholarly journals Hydrothermal synthesis and characteristics of lanthanumdoped pb(Zr₀.₆₅Ti ₀.₃₅)O₃ ceramics

2021 ◽  
Vol 8 (3) ◽  
pp. 14-19
Author(s):  
Thuy Nguyen Thanh ◽  
Tung Nguyen Van ◽  
Hung Nguyen Trong ◽  
Minh Cao Duy
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Dielectric Constant ◽  
Reaction Temperature ◽  
Lead Zirconate Titanate ◽  
Lead Zirconate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Influence Of Ph ◽  
Scanning Electron

Lanthanum-doped lead zirconate titanate (PLZT) powders were synthesized using thehydrothermal method. The influence of pH, reaction temperature and time, lanthanum concentration on the formation and characteristics of PLZT were investigated. Obtained powders were investigated using X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) techniques and a dielectric analyzer. The results showed that           Pb1-xLax(Zr0.65Ti0.35)O3 with x= 0.0 – 0.1 were well formed under conditions: pH≥13, reaction time of 12hrs, reaction temperature of 180oC. Dielectric constant of PLZT is higher than PZT. The grain size of the PLZT is found to be 1–3.5 µm.

scholarly journals SYNTHESIS AND DIELECTRIC PROPERTIES OF FOUR-LAYERED AURIVILLIUS SrBi4Ti4O15 DOPED Nd3+ AND Mn4+

2016 ◽  
Vol 11 (2) ◽  
pp. 127
Author(s):  
Sestry Misfadhila ◽  
Evi Adhelina ◽  
Yestria Rilda ◽  
Syukri Arief ◽  
Zulhadjri Zulhadjri
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Dielectric Constant ◽  
Xrd Analysis ◽  
Orthorhombic Symmetry ◽  
Molten Salt Method ◽  
X Ray Diffraction ◽  
Aurivillius Phase ◽  
X Ray ◽  
Scanning Electron

<p>Synthesis of four-layered Aurivillius compound doped with Nd<sup>3+</sup> and Mn<sup>4+ </sup>cations, SrBi<sub>3.5</sub>Nd<sub>0.5</sub>Ti<sub>4-x</sub>Mn<sub>x</sub>O<sub>15</sub> (<em>x</em> = 0; 0.5; 1) was carried out using molten salt method with a mixture of Na<sub>2</sub>SO<sub>4</sub>/K<sub>2</sub>SO<sub>4</sub> as a flux. The synthesized products were characterized using X-ray diffraction (XRD) and refined by <em>Le Bail</em> technique. The results of XRD analysis show that the four-layered Aurivillius compound formed, however there are additional peaks identified as perovskite and Bi<sub>7.68</sub>Ti<sub>0.32</sub>O<sub>12.16</sub>  phases for <em>x</em> = 0 and perovskite and Sr<sub>4</sub>Ti<sub>3</sub>O<sub>10</sub>phases for <em>x</em> = 0.5 and 1. The results of refinement show that four-layered Aurivillius phase formed has orthorhombic symmetry with <em>A2<sub>1</sub>am</em> space group. Scanning Electron Microscopy (SEM) shows the plate like morphology that are characteristic of Aurivillius compound. Dielectric constant of the samples show increasing value as increasing of Mn<sup>4+</sup> concentration.</p>

Controlled Growth of SnO2 Micro/Nanocrystals with Different Morphologies via a Solution Method

2009 ◽  
Vol 66 ◽  
pp. 155-158 ◽  
Author(s):  
Tie Kun Jia ◽  
Wei Min Wang ◽  
Zheng Yi Fu ◽  
Fei Huang ◽  
Hao Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Solution Method ◽  
Sno2 Nanoparticles ◽  
X Ray Diffraction ◽  
Forming Process ◽  
X Ray ◽  
Synthesis Conditions ◽  
Sno2 Nanocrystals ◽  
Scanning Electron

SnO2 nanocrystals with various morphologies were synthesized via a hydrothermal method assisting by the surfactant CTAB. The morphologies of the products were significantly dependent on the synthesis conditions. The products were characterized by X-ray diffraction (XRD) and field scanning electron microscopy (FESEM).The results showed products SnO2 nanoparticles and spheres like structure assembled with nanocones were obtained by varying the dosage of CTAB and the concentration of NaOH. The forming process of SnO2 sphere like structure was discussed and the proposed mechanism was put forward in this work.

scholarly journals SYNTHESIS AND DIELECTRIC PROPERTIES OF FOUR-LAYERED AURIVILLIUS SrBi4Ti4O15 DOPED Nd3+ AND Mn4+

2016 ◽  
Vol 11 (2) ◽  
pp. 127
Author(s):  
Sestry Misfadhila ◽  
Evi Adhelina ◽  
Yestria Rilda ◽  
Syukri Arief ◽  
Zulhadjri Zulhadjri
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Dielectric Constant ◽  
Xrd Analysis ◽  
Orthorhombic Symmetry ◽  
Molten Salt Method ◽  
X Ray Diffraction ◽  
Aurivillius Phase ◽  
X Ray ◽  
Scanning Electron

<p>Synthesis of four-layered Aurivillius compound doped with Nd<sup>3+</sup> and Mn<sup>4+ </sup>cations, SrBi<sub>3.5</sub>Nd<sub>0.5</sub>Ti<sub>4-x</sub>Mn<sub>x</sub>O<sub>15</sub> (<em>x</em> = 0; 0.5; 1) was carried out using molten salt method with a mixture of Na<sub>2</sub>SO<sub>4</sub>/K<sub>2</sub>SO<sub>4</sub> as a flux. The synthesized products were characterized using X-ray diffraction (XRD) and refined by <em>Le Bail</em> technique. The results of XRD analysis show that the four-layered Aurivillius compound formed, however there are additional peaks identified as perovskite and Bi<sub>7.68</sub>Ti<sub>0.32</sub>O<sub>12.16</sub>  phases for <em>x</em> = 0 and perovskite and Sr<sub>4</sub>Ti<sub>3</sub>O<sub>10</sub>phases for <em>x</em> = 0.5 and 1. The results of refinement show that four-layered Aurivillius phase formed has orthorhombic symmetry with <em>A2<sub>1</sub>am</em> space group. Scanning Electron Microscopy (SEM) shows the plate like morphology that are characteristic of Aurivillius compound. Dielectric constant of the samples show increasing value as increasing of Mn<sup>4+</sup> concentration.</p>

Identification of calcium oxalate crystals in dried or fixed tobacco leaf

1984 ◽  
Vol 42 ◽  
pp. 288-289
Author(s):  
Vicki L. Baliga ◽  
Mary Ellen Counts
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Calcium Oxalate ◽  
Growth And Development ◽  
Polarized Light ◽  
Calcium Oxalate Crystals ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

Calcium is an important element in the growth and development of plants and one form of calcium is calcium oxalate. Calcium oxalate has been found in leaf seed, stem material plant tissue culture, fungi and lichen using one or more of the following methods—polarized light microscopy (PLM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and x-ray diffraction.Two methods are presented here for qualitatively estimating calcium oxalate in dried or fixed tobacco (Nicotiana) leaf from different stalk positions using PLM. SEM, coupled with energy dispersive x-ray spectrometry (EDS), and powder x-ray diffraction were used to verify that the crystals observed in the dried leaf with PLM were calcium oxalate.

Environmental scanning electron microscopy of fresh human gallstones reveals new morphologies of precipitated calcium salts

1992 ◽  
Vol 50 (2) ◽  
pp. 1322-1323
Author(s):  
Howard S. Kaufman ◽  
Keith D. Lillemoe ◽  
John T. Mastovich ◽  
Henry A. Pitt
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Environmental Scanning Electron Microscopy ◽  
Environmental Scanning ◽  
X Ray Diffraction ◽  
Calcium Salts ◽  
Cholesterol Gallstones ◽  
X Ray ◽  
Ca Carbonate ◽  
Scanning Electron

Gallstones contain precipitated cholesterol, calcium salts, and proteins. Calcium (Ca) bilirubinate, palmitate, phosphate, and carbonate occurring in gallstones have variable morphologies but characteristic windowless energy dispersive x-ray (EDX) spectra. Previous studies of gallstone microstructure and composition using scanning electron microscopy (SEM) with EDX have been limited to dehydrated samples. In this state, Ca bilirubinates appear as either glassy masses, which predominate in black pigment stones, or as clusters, which are found mostly in cholesterol gallstones. The three polymorphs of Ca carbonate, calcite, vaterite, and aragonite, have been identified in gallstones by x-ray diffraction, however; the morphologies of these crystals vary in the literature. The purpose of this experiment was to study fresh gallstones by environmental SEM (ESEM) to determine if dehydration affects gallstone Ca salt morphology.Gallstones and bile were obtained fresh at cholecystectomy from 6 patients. To prevent dehydration, stones were stored in bile at 37°C. All samples were studied within 4 days of procurement.

PENINGKATAN LAJU DISOLUSI ACYCLOVIR DENGAN METODE SISTEM DISPERSI PADAT MENGGUNAKAN POLOXAMER 188

2016 ◽  
Vol 5 (1) ◽  
pp. 6
Author(s):  
Budi Setiawan ◽  
Erizal Zaini ◽  
Salman Umar
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Differential Thermal Analysis ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
Poloxamer 188 ◽  
X Ray ◽  
Scanning Electron

Sebuah penelitian tentang sistem dispersi padat dari asiklovir dengan poloxamer 188 telah dilakukan formulasi dengan pencampuran secara fisika dengan rasio 1 : 1, 1 : 3, 1 : 5 dan dispersi padat 1 : 1, 1 : 3, 1 : 5 dan penggilingan 1:1 sebagai pembanding. Dispersi padat dibuat menggunakan metode pencairan (fusi), yang digabung dengan poloxamer 188 pada hotplate kemudian asiklovir dimasukkan ke dalam hasil poloxamer 188 lalu di kocok hingga membentuk masa homogen. Semua formula yang terbentuk termasuk asiklovir poloxamer 188 murni dianalisis karakterisasinya dengan Differential Thermal Analysis (DTA), X-ray Diffraction, Scanning Electron Microscopy (SEM), dan Fourier Transform Infrared (FTIR), kemudian pengambilan dilakukan  (penentuan kadar) mengunakan spektrofotometer UV pada panjang gelombang 257,08 nm dan uji laju disolusi dengan aquadest bebas CO2 menggunakan metode dayung. Hasil pengambilan  (penentuan kadar) menunjukkan bahwa semua formula memenuhi persyaratan farmakope Amerika edisi 30 dan farmakope Indonesia edisi 4 yaitu 95-110%. Sedangkan hasil uji laju disolusi untuk campuran fisik 1: 1, dan dispersi padat 1: 1, dan penggilingan 1: 1 menunjukkan peningkatan yang nyata dibandingkan asiklovir murni. Hal ini juga dapat dilihat dari hasil perhitungan statistik  menggunakan analisis varian satu arah  SPSS 17.

Structural Characterization of Gallbladder Stones Using Energy Dispersive X-ray Spectroscopy and X-ray Diffraction

2018 ◽  
Vol 21 (7) ◽  
pp. 495-500 ◽  
Author(s):  
Hassan A. Almarshad ◽  
Sayed M. Badawy ◽  
Abdalkarem F. Alsharari
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Energy Dispersive ◽  
Spectroscopic Techniques ◽  
X Ray Diffraction ◽  
Major Health Problem ◽  
X Ray ◽  
Gallbladder Stones ◽  
Pure Cholesterol ◽  
Scanning Electron

Aim and Objective: Formation of the gallbladder stones is a common disease and a major health problem. The present study aimed to identify the structures of the most common types of gallbladder stones using X-ray spectroscopic techniques, which provide information about the process of stone formation. Material and Method: Phase and elemental compositions of pure cholesterol and mixed gallstones removed from gallbladders of patients were studied using energy-dispersive X-ray spectroscopy combined with scanning electron microscopy analysis and X-ray diffraction. Results: The crystal structures of gallstones which coincide with standard patterns were confirmed by X-ray diffraction. Plate-like cholesterol crystals with laminar shaped and thin layered structures were clearly observed for gallstone of pure cholesterol by scanning electron microscopy; it also revealed different morphologies from mixed cholesterol stones. Elemental analysis of pure cholesterol and mixed gallstones using energy-dispersive X-ray spectroscopy confirmed the different formation processes of the different types of gallstones. Conclusion: The method of fast and reliable X-ray spectroscopic techniques has numerous advantages over the traditional chemical analysis and other analytical techniques. The results also revealed that the X-ray spectroscopy technique is a promising technique that can aid in understanding the pathogenesis of gallstone disease.

scholarly journals Analytical study of Buddha sculptures in Jingyin temple of Taiyuan, China

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Xiaojian Bai ◽  
Chen Jia ◽  
Zhigen Chen ◽  
Yuxuan Gong ◽  
Huwei Cheng ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Analytical Study ◽  
Energy Dispersive Spectrometry ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
Ancient China ◽  
X Ray ◽  
Unique Style ◽  
Scanning Electron

AbstractWith exquisite design and unique style, the painted sculptures of Tutang Buddha and two attendants Buddha in Jingyin Temple are precious cultural heritages of China. The sculpture of Tutang Buddha, which was carved from a mound and painted by ancient craftsmen, was rarely found in ancient China. However, due to natural and human factors, the sculptures were severely damaged. Obviously, they require urgent and appropriate protection and restoration. In this study, samples taken from the sculptures were analysed through multiple analytical techniques, including scanning electron microscopy with energy dispersive spectrometry (SEM–EDS), Raman spectroscopy, X-ray diffraction (XRD), optical microscopy (OM) and granulometry. The analysis results enable us to infer the techniques used by the craftsmen in making the sculptures and provide a reliable evidence for the conservation and future protection of these and similar sculptures.

Sign in / Sign up

Export Citation Format

Share Document