Study on Planning and Design of Production Facility for Bearing Manufacturing Industry Based on SLP

2012 ◽  
Vol 542-543 ◽  
pp. 428-432 ◽  
Author(s):  
Zong Xiang Huang ◽  
Hao Luo
Keyword(s):  
Production Cost ◽  
Manufacturing Industry ◽  
Production Efficiency ◽  
Production Facility ◽  
Production Flow ◽  
Comprehensive Utilization ◽  
Planning And Design ◽  
Operating Unit ◽  
Made In ◽  
Production Facilities

based on characteristics of production flow of bearing manufacturing, via comprehensive utilization of SLP tool and by calculating logistics quantity of bearing manufacturing, this paper works out the operating unit logistics and non-logistics correlation diagram based on analysis of benchmark interrelationship, and then it gets the comprehensive correlation among production facilities. In addition, the operating unit’s location interrelationship scheme of bearing manufacturing industry is made. In this way, planning of production facilities of enterprise can be more reasonable, thus production efficiency can be improved and production cost can be reduced.

The Applied Analysis of Virtual Technology in Modern Manufacturing Industry

2012 ◽  
Vol 503-504 ◽  
pp. 107-110 ◽  
Author(s):  
Mei Hong Liao
Keyword(s):  
Manufacturing Process ◽  
Production Cost ◽  
Manufacturing Industry ◽  
Production Efficiency ◽  
Manufacturing Technology ◽  
Virtual Manufacturing ◽  
Simulation Technology ◽  
Virtual Technology ◽  
Practical Applications ◽  
Modern Manufacturing

Virtual mechanical manufacturing technology refers to a simulation technology for the mechanical manufacturing process whose objectives are to reduce the production cost and increase the production efficiency. This paper is intended to probe into the practical applications of computer virtual manufacturing technology in modern manufacturing industry combining with the latest development in the virtual mechanical manufacturing technology.

scholarly journals Relayout Production Facility of PC. Spun Pile Using Systematic Layout Planning in ABC Factory

2020 ◽  
Vol 5 (8) ◽  
pp. 1620-1629
Author(s):  
Muhammad Ainun Naim ◽  
Erry Rimawan ◽  
Mahmud . ◽  
Adinda Putri
Keyword(s):  
Precast Concrete ◽  
Production Capacity ◽  
Production Method ◽  
Major Effect ◽  
Production Cycle ◽  
Production Facility ◽  
Production Flow ◽  
Layout Planning ◽  
Systematic Layout Planning ◽  
Production Facilities

ABC Factory is one of the companies engaged in manufacturing precast concrete in Indonesia. This company was established in 1978 under the auspices of XYZ Group Since. The products produced by ABC Factory are Precast Concrete / Prefabricated Concrete or often abbreviated as "PC". Some of the products manufactured by ABC Factory are PC. Spun Pile, PC. Square Pile, PC. Spun Pole (Electric Pole), PC. I Girder, PC. Box Girder and several other products. ABC Factory uses the Make to Order production method, so it is demanded to produce orders maximally and as efficiently as possible. In this manufacturing company, the preparation of the layout of production facilities greatly affects the production cycle time which in turn will have a major effect on the company's production capacity. for that, the company needs to redesign the layout of the PC production facility of Spun Pile with the best production flow. Based on these problems, the method used is to use the SLP (Systematic Layout Planning) method which functions to produce a layout design for production facilities that minimizes material movement distance and produces a good production flow in ABC Factory. Based on the results of the study obtained a reduction in the distance of material flow facility layout by 72.71 meters and an increase in production capacity of 138 cigarettes or 13.44% of the initial layout.

M. A. Ayuh. Made in Jamaica: The Development of Manufacturing Sector. Baltimore: The Johns Hopkins University Press. 1981. xxii+128 pp.

1986 ◽  
Vol 25 (1) ◽  
pp. 93-95
Author(s):  
Najam-us- Saqib
Keyword(s):  
Manufacturing Industry ◽  
Manufacturing Sector ◽  
Policy Makers ◽  
Industrial Base ◽  
Johns Hopkins University ◽  
Key Characteristics ◽  
The World ◽  
Caribbean Country ◽  
Bauxite Ore ◽  
Made In

Jamaica, known in the world for her rich deposits of bauxite ore, is a small Caribbean country with an area of 10991 square kilometers and a population of just over two million individuals. This beautifu11and, which was described by Columbus as "The fairest isle that eyes have beheld" has developed a remarkably diversified manufacturing sector starting from a modest industrial base. Jamaica's manufacturing industry enjoyed a respectable growth rate of about 6 percent per annum during the good old days of the euphoric '50s and '60s. However, those bright sunny days ''when to live was bliss" were followed by the chilling winter of much subdued progress. The rise and fall of growth have aroused considerable interest among economists and policy• makers. The book under review probes the causes of this behaviour by analysing key characteristics of Jamaican manufacturing sector and tracing its path of evolution.

scholarly journals 110 Managing Feed Efficiency to Improve Dairy Farm Margin

2020 ◽  
Vol 98 (Supplement_3) ◽  
pp. 20-20
Author(s):  
Micheal J Brouk
Keyword(s):  
Milk Production ◽  
Production Cost ◽  
Dairy Farm ◽  
Animal Reproduction ◽  
High Feed ◽  
Efficiency Factors ◽  
Feed Costs ◽  
The Cost ◽  
The Impact ◽  
Made In

Abstract Dairy farm margin has continued to be a challenge for the dairy industry. Several years of challenging milk prices with limited relief from high feed costs and increasing production cost have continued to erode the net margin of US dairy farms. As dairy producers continue to operate in a challenging economic environment, discoveries are being made in various farm efficiencies to improve farm margin. Increased management intensity on all aspects of the dairy farm is resulting in the discover of and improvement of many individual efficiency factors. Key areas of economic efficiency include feed, animal reproduction, replacement animals, labor and resource allocation. Often the answer to improved efficiency involves more than just reduced production cost, but also in the improvement of production to reduce the cost per unit of milk produced. Identifying and focusing on the important factors that can improve overall farm efficiency will enable producers to weather the economic challenges. For dairy producers, one of the complications is the biology of the dairy cow and understanding how to utilize the biology correctly for improved efficiency of milk production. Improved efficiency of milk production requires attention to details in many areas of the dairy. Identifying the correct areas of deficiencies, establishing corrective plans of action and then careful evaluation of the impact of changes are all key to the overall success of improving dairy farm margins and efficiencies.

scholarly journals EVALUASI TATA LETAK FASILITAS PRODUKSI KRIPIK PISANG PADA CAHAYA INDI KABUPATEN DONGGALA

2020 ◽  
Vol 3 (1) ◽  
pp. 27-40
Author(s):  
Pria Tubagus ◽  
Saharuddin Kaseng ◽  
Asngadi Asngadi
Keyword(s):  
Material Flow ◽  
Production Management ◽  
Production Efficiency ◽  
Layout Design ◽  
Idle Time ◽  
Line Balancing ◽  
Production Facility ◽  
Maximum Profit ◽  
Efficiency And Effectiveness ◽  
Initial Layout

Basically, the purpose of production management is directed to create production efficiency and effectiveness to improve the results and contribute to the maximum profit achievement of the company. One of the problems in production management that influences the efficiency and effectiveness of production is layout arrangement of production facilities. This research is conducted through direct observation in Banana Chips Company ‘Cahaya Indi’ located in Donggala District. The type of research is quantitative using line balancing method and travel chart. The result of the line balancing method shows the efficiency of banana chips production process is 90,73% with idle time of 9,27%. While the result of travel chart method indicates a new layout design of banana chips production facility at Cahaya Indi is more effective with material flow load of 198,83 from the initial layout of 259,93. Pada dasarnya, tujuan manajemen produksi selalu diarahkan pada terciptanya efisiensi dan efektifitas produksi, agar dapat meningkatkan hasil produksi serta memberikan konstribusi yang maksimal terhadap laba perusahaan. Salah satu permasalahan manajemen produksi yang berpengaruh terhadap efisiensi dan efektifitas produksi adalah pengaturan tata letak (layout) fasilitas produksi. Penelitian ini dilakukan dengan cara observasi langsung pada Cahaya Indi yang bertempat di Kabupaten Donggala. Jenis penelitian yang diguanakan adalah penelitian kuantitatif dengan menggunakan metode line balancing dan travel chart. Hasil penelitian dengan menggunakan metode line balancing diperoleh efisiensi dari proses produksi kripik pisang sebesar 90,73% dengan waktu menganggur 9,27%. Sedangkan hasil dari metode travel chart diperoleh rancangan baru tata letak fasilitas produksi kripik pisang pada Cahaya Indi yang lebih efektif sebesar 198,83 beban aliran bahan dari tata letak mula-mula sebesar 259,93 beban aliran bahan.

Research on Intelligent Optimization Algorithm for Multi-Objective Disassembly Line Balancing Problem

2020 ◽  
Author(s):  
Yunli Xu ◽  
Bitao Yao ◽  
Duc Truong Pham
Keyword(s):  
Manufacturing Industry ◽  
Production Efficiency ◽  
Line Balancing ◽  
Product Complexity ◽  
Intelligent Optimization ◽  
Combination Scheme ◽  
Objective Space ◽  
Disassembly Line Balancing ◽  
Low Efficiency ◽  
Disassembly Line

Abstract For resource reutilization and environmental protection, remanufacturing gets more and more attention in many countries. Disassembly is a critical part of traditional manufacturing industry, but the traditional disassembly operation is mainly done by workers, which is low-efficiency. Now the use of robots can improve production efficiency a lot, which involves the problem of disassembly line balancing. Due to the constraints such as product complexity and precedence relationship between tasks, when the number of tasks increases, the combination scheme between tasks increases geometrically, and conventional algorithms are difficult to solve the problems, the Disassembly Line Balancing Problem (DLBP) is generally necessary to optimize multiple objectives. In this research, the author selects a variety of intelligent optimization algorithms to resolve the complex disassembly line balancing problem in different dimensional objective space. Four representative algorithms are selected from three angles to be compared through three performance indicators. It is concluded that these algorithms have different search capabilities for different specifications and objective space. Researchers should carefully select the algorithm according to the specific disassembly problem. The appropriate algorithm should be selected according to the scale of the disassembly line problem and the number of optimization objectives in actual production practice.

Cinema Made in Liège: A ‘Hub’ of Francophone Belgian Filmmaking

Cinéma-monde ◽  
2018 ◽  
Author(s):  
Jamie Steele
Keyword(s):  
Metropolitan Area ◽  
Local Level ◽  
Post Production ◽  
Production Knowledge ◽  
Surrounding Areas ◽  
The City ◽  
Made In ◽  
Production Facilities

This chapter considers the development of both ‘regional’ and ‘local’ funds and institutions – such as Wallimage and Pôle Image de Liège - that are designed to support local filmmaking activity and to entice projects to the city and the surrounding areas. This discussion engages with two key strands: (1) the attraction of co-production finance for ‘regional’ or ‘national’ film projects, and (2) the use of Liège as a production base. The first strand will develop the extent to which ‘regional’ film funds and institutions have production ‘knowledge’ on a local level. This is particularly the case for the Dardenne brothers, Bouli Lanners, Joachim Lafosse, Micha Wald, and Lucas Belvaux, whose films are all shot and located in the metropolitan area of Liège and are co-productions with France. The second strand. focuses on ‘runaway’ and minority-Belgian co-productions and considers how Liège has functioned as a key milieu for international co-productions, and how the city’s post-production facilities have been used for films such as De rouille et d’os (Jacques Audiard, 2012).

scholarly journals Towards Lean Teaching: Non-Value-Added Issues in Education

2020 ◽  
Vol 10 (6) ◽  
pp. 160
Author(s):  
Silvia Martínez Sanahuja
Keyword(s):  
Manufacturing Industry ◽  
Value Added ◽  
Lean Thinking ◽  
Lean Principles ◽  
Service Companies ◽  
Made In

Lean Thinking is a methodology based on improving the efficiency of productive processes by removing non-value-added issues. This methodology was firstly applied in the manufacturing industry, but it has also been applied to many service companies, bringing very good results. In the last decade, some works have tried to research the adaptation of Lean principles and practices to teaching, especially in technology and other STEAM subjects. In this sense, the aim of this work is to deepen this new trend by establishing what issues are non-value-added (waste) ones in education and classifying these kinds of waste in order to be able to analyze how to eliminate them. For this purpose, we adapt the classification made in other kinds of processes and extend other authors’ findings regarding this topic.

Large Diameter Deepwater Gas Pipelines Subjected to Global Buckling Behavior

2019 ◽  
Author(s):  
Bruno R. Antunes ◽  
Rafael F. Solano ◽  
Carlos O. Cardoso
Keyword(s):  
Structural Integrity ◽  
High Pressures ◽  
Large Diameter ◽  
Hydrate Formation ◽  
Gas Pipelines ◽  
Production Flow ◽  
Buckling Behavior ◽  
Production Platform ◽  
Global Buckling ◽  
Made In

Abstract In general, gas export pipeline designs have low restrictions concerning the flow assurance requirements, i. e., hydrate formation is not a great concern once processes in production platform facilities can significantly decrease the water content in the gas to be exported. Thus, these pipelines have only a small thickness of a single or multilayer anticorrosive coating and export gas at low temperatures. However, high pressures are required in order to overcome long distances and to increase the production flow rates. Large diameter gas pipelines submitted to high pressures even with low associated temperatures can be susceptible to global buckling, mainly if the pipelines are simply rested on a seabed of low resistance. This scenario characterizes strictly the gas pipelines installed in Brazilian Pre-Salt fields, where currently a relevant amount of export lines is operating in these conditions. Post-installation and operating pipeline surveys have identified marks on seabed confirming the buckle formation in some gas pipelines. In addition, axial movements of end equipment (PLETs) have been also observed. These issues require at least a verification and confirmation of the assumptions and predictions made in detailed design phase. This paper aims to present evaluations of the global buckling behavior of large diameter deepwater gas pipelines. Lateral buckles on very soft clayey seabed and displacements in ends and crossing locations are addressed in this work. Finally, numerical analyses confirm that gas pipelines structural integrity has not been jeopardized.

scholarly journals Increasing The Efficiency of The Cub Engine Assembly Lines In The Automotive Industry Using Ranked Positional Weight

2018 ◽  
Vol 218 ◽  
pp. 04028
Author(s):  
Inaki Maulida Hakim ◽  
Syarafi Auzan Mu’min ◽  
Rolina Oktapiani Zaqiah
Keyword(s):  
Production Process ◽  
Automotive Industry ◽  
Manufacturing Industry ◽  
Assembly Line ◽  
Consumer Demand ◽  
Assembly Lines ◽  
Production Flow ◽  
Subsequent Increase ◽  
The Right ◽  
Positional Weight

In this modern era, the competition among the manufacturing industry, especially in the automotive sector will become increasingly tight which causes companies need to innovate so that satisfaction of the consumer can be maintained. The production process will be an important aspect in the automotive industry to maintain the quality of products and ensure consumer demand can be fulfilled. The problems that often occur in the production process is in the form of production flow constraints caused by workload unbalanced in the assembly lines. The imbalance causes the assembly lines do not run in a cycle time that is determined, so that consumer demand can not be meet in the right amount and companies need to spend more to mitigate them. Therefore, this study was conducted to balance workload on the assembly line by using line balancing form Ranked Positional Weight (RPW) with a subsequent increase in the efficiency and productivity of assembly line that affect production process runs without any contraints.

Sign in / Sign up

Export Citation Format

Share Document