Effect of Coupling Agent on Mechanical Properties of Composite from Microcrystalline Cellulose and Recycled Polypropylene

2012 ◽  
Vol 576 ◽  
pp. 390-393 ◽  
Author(s):  
J. Awanis ◽  
S. Anis Sofia ◽  
Noorasikin Samat
Keyword(s):  
Mechanical Properties ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
Flexural Strength ◽  
Microcrystalline Cellulose ◽  
Coupling Agent ◽  
Impact Test ◽  
Flexural Test ◽  
Recycled Polypropylene ◽  
The Impact

This study shows the effect of using 3-aminopropyltriethoxysilane (APS) and maleic anhydride-grafted polypropylene (MAPP) as coupling agent on composite of RPP/MCC fiber. The compositions of MCC were varied from 0, 2, 4, 8 and 12 wt%. The compounded samples were prepared into test specimens by using injection moulding. The RPP/MCC composites with and without the coupling agent were characterized through mechanical testing of flexural and impact test. The incorporation of the modified MCC was found to increase the modulus and flexural strength. The flexural test indicates that the addition of 4 wt% MCC-APS and 8 wt% MCC-MAPP significantly increased the flexural strength of the RPP composite compared to the unmodified MCC. The impact test shows higher impact strength at 4 wt% of RPP/MCC-APS and 2 wt% of RPP/MCC-MAPP, respectively.

Effect of Tetradecyl Methyl Acrylate-Maleic Anhydride Copolymer on the Mechanical Properties of Glass Mat Reinforced Polypropylene Composites

2005 ◽  
Vol 13 (4) ◽  
pp. 403-413
Author(s):  
Shanhua Zhou ◽  
Zhiyu Xu ◽  
Xin Liu ◽  
Yan Gao ◽  
Qingzhi Dong
Keyword(s):  
Mechanical Properties ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polypropylene Composites ◽  
Monomer Ratio ◽  
Maleic Anhydride Copolymer ◽  
Glass Mat ◽  
The Impact ◽  
Interfacial Modifier

A new interfacial modifier made of tetradecyl methylacrylate-maleic anhydride copolymer (TMA- co-MAH) was prepared and characterized. The effect of reaction time and monomer ratio on the gross conversion and MAH content in the copolymer was studied. When the glass mat was treated with TMA- co-MAH solutions and compounded with PP, the MAH group of the interfacial modifier formed strong interactions with the glass mat and the long side chain of the interfacial modifier entangled firmly with the polypropylene matrix. In comparison with maleated polyolefins, the higher MAH content of the TMA- co-MAH resulted in better interfacial adhesion between the PP and the glass mat resulting in increased flexural strength and modulus, and the ductility of the TMA- co-MAH introduced a ductile interlayer into the interface of the glass mat reinforced polypropylene composites (GMT-PPs) to achieve higher impact strength. Therefore the mechanical properties of composites treated with TMA- co-MAH were all superior to those of GMT-PPs treated with maleic anhydride grafted polypropylene (PP- g-MAH) solutions when they were used at the same level. The effects of anhydride content, concentration of copolymer and compounding time on the mechanical property of GMT-PPs were investigated. With the optimal monomer ratio, MAH:TMA = 7:3, a 3% copolymer solution and a compounding time of 5 min, the impact strength, flexural strength and modulus of GMT-PPs treated with the new interfacial modifier were all improved significantly compared with composites treated with 0.3% PP- g-MAH solution.

Manufacturing and Mechanical Property Evaluations of CF/PLA Biocomposites

2014 ◽  
Vol 910 ◽  
pp. 153-156
Author(s):  
Ching Wen Lou ◽  
Jo Mei Liao ◽  
Zheng Lan Lin ◽  
Jia Horng Lin
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Tensile Test ◽  
Carbon Fibers ◽  
Impact Test ◽  
Flexural Modulus ◽  
Flexural Test

This study uses carbon fibers (CF) to reinforce polylactic acid (PLA) matrices to form CF/PLA biocomposites. Tensile test, flexural test, and impact test are performed on biocomposites to evaluate their mechanical properties. The results of tests show that an increment of the CF content results in an increase in tensile strength, flexural strength, flexural modulus, and impact strength. The combination of 15 wt% CF provides the resulting biocomposites with a 72 % increase in tensile strength, a 322 % increase in flexural modulus, and a 96 % increase in impact strength.

A novel recycled polyethylene terephthalate/polyamide 11 (rPET/PA11) thermoplastic blend

2021 ◽  
pp. 147776062110010
Author(s):  
Zahid Iqbal Khan ◽  
Zurina Binti Mohamad ◽  
Abdul Razak Bin Rahmat ◽  
Unsia Habib ◽  
Nur Amira Sahirah Binti Abdullah
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Practical Implication ◽  
Polyamide 11 ◽  
Recycled Polyethylene ◽  
Twin Screw ◽  
Electron Microscopy Analysis ◽  
The Impact

This work explores a novel blend of recycled polyethylene terephthalate/polyamide 11 (rPET/PA11). The blend of rPET/PA11 was introduced to enhance the mechanical properties of rPET at various ratios. The work’s main advantage was to utilize rPET in thermoplastic form for various applications. Three different ratios, i.e. 10, 20 and 30 wt.% of PA11 blend samples, were prepared using a twin-screw extruder and injection moulding machine. The mechanical properties were examined in terms of tensile, flexural and impact strength. The tensile strength of rPET was improved more than 50%, while the increase in tensile strain was observed 42.5% with the addition of 20 wt.% of PA11. The improved properties of the blend were also confirmed by the flexural strength of the blends. The flexural strength was increased from 27.9 MPa to 48 MPa with the addition of 30 wt.% PA11. The flexural strain of rPET was found to be 1.1%. However, with the addition of 10, 20 and 30 wt.% of PA11, the flexural strain was noticed as 1.7, 2.1, and 3.9% respectively. The impact strength of rPET/PA11 at 20 wt.% PA11 was upsurged from 110.53 to 147.12 J/m. Scanning electron microscopy analysis revealed a dispersed PA11 domain in a continuous rPET matrix morphology of the blends. This work practical implication would lead to utilization of rPET in automobile, packaging, and various industries.

Effect of Filler Compositions on the Mechanical Properties of Bamboo Filled Polyester Composite

2014 ◽  
Vol 879 ◽  
pp. 90-95 ◽  
Author(s):  
Abdul Rahman Noor Leha ◽  
Nor Amalina Nordin
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Impact Test ◽  
Compression Molding ◽  
Engineering Applications ◽  
Maximum Value ◽  
Polyester Composite ◽  
Bamboo Powder ◽  
Flexural Tests ◽  
The Impact

Biocomposite from bamboo powder was fabricated by compression molding technique. The objective of this study was to investigate the mechanical properties of bamboo compounded with epoxy with different ratio. Tensile and flexural tests were done to characterize its mechanical properties. It was observed that the strength of bamboo-polyester was increased with increasing amount of bamboo powder. The tensile and flexural strength shows the highest value at 25 wt.% bamboo. However, the impact test shows the maximum value at 20 wt.% bamboo powder. These results exhibit the bamboo-polyester can be a good candidate to be used in many engineering applications

Effects of microcrystalline cellulose on the mechanical properties of low-density polyethylene composites

2018 ◽  
Vol 32 (3) ◽  
pp. 297-311 ◽  
Author(s):  
Yousef Ahmad Mubarak ◽  
Raghda Talal Abdulsamad
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Impact Strength ◽  
Tensile Properties ◽  
Microcrystalline Cellulose ◽  
Weight Fraction ◽  
Low Density Polyethylene ◽  
Low Density ◽  
Ldpe Composites ◽  
The Impact

This work was intended to provide an understanding of the effect of microcrystalline cellulose (MCC) on the mechanical properties of low-density polyethylene (LDPE). The impact resistance and the tensile properties of low-density LDPE/MCC composites were investigated. The weight fraction of MCC was varied at (0, 0.5, 1, 2.5, 5, 10, 20, and 30 wt%). The obtained blends were then used to prepare the required tensile and impact testing samples by hot compression molding technique. It has been found that MCC has a strong influence on the mechanical properties of LDPE. At a low MCC weight fraction, there was a little improvement in the ultimate strength, fracture stress, and elongation at break, but at a high MCC weight fraction, the tensile properties were deteriorated and reduced significantly. The addition of 1 wt% MCC to LDPE enhanced the mentioned properties by 10, 25, and 6%, respectively. While at 30 wt% MCC, these properties were lowered by 36, 25, and 96%. The elastic modulus of LDPE composites was improved on all MCC weight fractions used in the study, at 20 wt% MCC, an increase in the elastic modulus by 12 folds was achieved. On the other hand and compared with the impact strength of pure LDPE, the addition of MCC particles enhanced the impact strength, the highest value obtained was for LDPE composites filled with 10 wt% MCC where the impact strength enhanced by two folds.

Preparing of SMC Artificial Marble and its Mechanical Properties

2011 ◽  
Vol 55-57 ◽  
pp. 447-450 ◽  
Author(s):  
Jian Li ◽  
Zheng Qun Huang ◽  
Yan Qin
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fiber Length ◽  
Filler Content ◽  
Fiber Content ◽  
Molding Temperature ◽  
Overall Performance ◽  
The Impact

In this article, a kind of SMC artificial marble was prepared. In order to enhance the mechanical properties and prolong the using life of SMC artificial marble, some effects such as fiber content, filler content and molding temperature etc. on the mechanical properties were carefully studied, too. Results showed that the increase of fiber content could improve the impact strength of SMC artificial marble when the fiber length was 10mm and the increase of filler content would decrease the flexural strength of SMC artificial marble. And the molding temperature at the range of 130°C ~ 160°C had little influence on the mechanical properties of SMC artificial marble. Comparing with natural marble and casting marble, SMC artificial marble owed superior overall performance and it was much more suitable for industry production.

Electrical and Mechanical Properties of Carbon Aerogels / Phenolic Resin for Nanocomposites

2011 ◽  
Vol 236-238 ◽  
pp. 1725-1730 ◽  
Author(s):  
Wei Jen Chen ◽  
Ming Yuan Shen ◽  
Yi Luen Li ◽  
Chin Lung Chiang ◽  
Ming Chuen Yip
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Phenolic Resin ◽  
Surface Conductivity ◽  
Carbon Aerogels ◽  
Polymer Resin ◽  
The Impact ◽  
Humidity Environment

This study used carbon aerogels (CA) and phenolic resin in fixed proportations to produce nano high polymer resin, and used poly ehtylene oxide (PEO) as the modifying agent for phenolic resin to improve the mechanical properties of phenolic resin and promote the surface conductivity. The prepared nano high polymer resin and carbon cloth were made into nano-prepreg by using ultrasonic impregnation method, and a nano-prepreg composite material was prepared by using hot compacting and cut to test pieces to measure its mechanical properties and surface conductivity as well as the influence of temperature-humidity environment (85°C/168hr and 85°C/85%RH/168hr) on mechanical properties. The result showed that the surface conductivity increased by 64.55%, the tensile strength at room temperature increased by 35.7%, the flexural strength increased by 18.4%, and the impact strength increased by 101%. In hot environment (85°C/168hr), the tensile strength decreased by 23.8%, the flexural strength increased by 3.1%, and the impact strength increased by 84.6%. In high temperature-high humidity environment (85°C/85% RH/168hr), the tensile strength decreased by 29.6%, the flexural strength decreased by 17%, and the impact strength increased by 95.7%.Introduction

scholarly journals Effect of repeated disinfections by microwave energy on the physical and mechanical properties of denture base acrylic resins

2009 ◽  
Vol 20 (2) ◽  
pp. 132-137 ◽  
Author(s):  
Rafael Leonardo Xediek Consani ◽  
Douglas Duenhas de Azevedo ◽  
Marcelo Ferraz Mesquita ◽  
Wilson Batista Mendes ◽  
Paulo César Saquy
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Flexural Strength ◽  
Physical And Mechanical Properties ◽  
Knoop Hardness ◽  
Microwave Energy ◽  
Bending Test ◽  
Denture Base ◽  
Acrylic Resins ◽  
The Impact

The present study evaluated the effect of repeated simulated microwave disinfection on physical and mechanical properties of Clássico, Onda-Cryl and QC-20 denture base acrylic resins. Aluminum patterns were included in metallic or plastic flasks with dental stone following the traditional packing method. The powder/liquid mixing ratio was established according to the manufacturer's instructions. After water-bath polymerization at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling and finished. Each specimen was immersed in 150 mL of distilled water and underwent 5 disinfection cycles in a microwave oven set at 650 W for 3 min. Non-disinfected and disinfected specimens were subjected to the following tets: Knoop hardness test was performed with 25 g load for 10 s, impact strength test was done using the Charpy system with 40 kpcm, and 3-point bending test (flexural strength) was performed at a crosshead speed of 0.5 mm/min until fracture. Data were analyzed statistically by ANOVA and Tukey's test (α= 0.05%). Repeated simulated microwave disinfections decreased the Knoop hardness of Clássico and Onda-Cryl resins and had no effect on the impact strength of QC-20. The flexural strength was similar for all tested resins.

scholarly journals Mechanical Properties of Green Recycled Polypropylene Composites: Effect of Maleic Anhydride Grafted Polypropylene (MAPP) Coupling Agent

2013 ◽  
Vol 812 ◽  
pp. 187-191 ◽  
Author(s):  
Nur Izzati Zulkifli ◽  
Noorasikin Samat
Keyword(s):  
Mechanical Properties ◽  
Maleic Anhydride ◽  
Coupling Agent ◽  
Filler Content ◽  
Mechanical Analysis ◽  
Morphological Properties ◽  
Appreciable Change ◽  
Polypropylene Composites ◽  
Recycled Polypropylene ◽  
Tensile Impact

Recycled polypropylene/microcrystalline cellulose (rPP/MCC) composites were prepared by adding different loadings of maleic anhydride grafted polypropylene (MAPP) coupling agent. The tensile, impact and morphological properties of the composites were investigated. The obtained results show that the tensile and impact strengths of the composites were significantly enhanced with the addition of MAPP loading from 2 to 5 wt%, as compared with unfilled rPP/MCC composites. However, it was found that at low filler content, different amounts of MAPP resulted in no appreciable change in the tensile strength and modulus. Moreover, dynamic mechanical analysis (DMA) results indicated that, increasing the amount of MAPP loading from 2 to 5 wt% in rPP/MCC provide better stiffness of the composite compared to those neat rPP and neat PP. Field emission scanning microscopy (FESEM) has shown that the composite, with MAPP loading, promotes better fibermatrix interaction.

Mechanical Properties, Morphology, Thermal Performance, Crystallization Behavior, and Kinetics of PP/Microcrystal Cellulose Composites Compatibilized by Two Different Compatibilizers

2011 ◽  
Vol 24 (6) ◽  
pp. 735-754 ◽  
Author(s):  
Z. Xiuju ◽  
S. Juncai ◽  
Y. Huajun ◽  
L. Zhidan ◽  
T. Shaozao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Crystallization Kinetics ◽  
Thermal Performance ◽  
Microcrystalline Cellulose ◽  
Heterogeneous Nucleation ◽  
Crystallization Temperature ◽  
Nonisothermal Crystallization

Polypropylene (PP)/microcrystalline cellulose (MCC) composites and PP/MCC composites modified by maleic anhydride grafted PP (PP-g-MA) and methyl acrylic acid glycidyl ester grafted PP (PP-g-GMA) respectively were prepared in a twin-screw extruder. The mechanical properties, morphology, and thermal performance were investigated. The nonisothermal crystallization, melting behavior, and nonisothermal crystallization kinetics were investigated by DSC. The results indicated that the addition of MCC had led to the increase of the tensile strength, impact strength, and flexural strength of PP. PP-g-GMA modification was more conducive to the improvement in tensile strength, impact strength, and flexural strength. The three types of PP/MCC composites have higher thermal decomposition temperatures, Vicat softening temperatures, and dimensional stability. Nonisothermal crystallizations of PP/MCC composites were in accordance with tridimensional growth with heterogeneous nucleation. Meanwhile, MCC was acted as the nucleating agent in PP matrix, which increased the crystallization temperature. PP-g-GMA further increased the crystallization temperature while PP-g-MA weakened the heterogeneous nucleation effect of MCC. Avrami equation and Mo method give a satisfactory description of the crystallization kinetics process. The activation energy of crystallization, nucleation constant, and fold surface free energy of PP were markedly reduced in PP/MCC composites and its compatibilized composites. The value of F( T) systematically increased with increasing relative degree of crystallinity. The addition of microcrystalline cellulose has greatly reduced the spherulitic size of PP.

Sign in / Sign up

Export Citation Format

Share Document