Orthodontics Simulation and Finite Element Analysis of Submaxilla Dentition

2012 ◽  
Vol 591-593 ◽  
pp. 712-716
Author(s):  
Dan Liu ◽  
Ai Li Qu ◽  
Chun Xiu Wang
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Force Transmission ◽  
Element Analysis ◽  
Engineering Software ◽  
Elastic Module ◽  
Bodily Movement ◽  
Bone Absorption ◽  
Single Tooth ◽  
Titanium Nickel

Objective The principle and method of the force application is researched in orthodontics field, providing the scale and location of force for clinical orthodontics. Methods Reverse engineering software is used to reconstruct a 3-D mandible finite element model, the MBT bracket and straight archwire on the dentition are modeled on it. Change the elastic module of archwire to simulate four stages of orthodontics and the displacement and stress on dentition and mandible are acquired. Results The finite element results of dentition and mandible under short Ⅱ elastics are obtained, the results show that titanium-nickel archwire may provide major displacement for dentition; O and stainless steel have good force-transmission in teeth. The stress of single tooth and mandible are symmetrical except for the position where loads are applied. Conclusions Under the short II elastics loads, bone absorption don’t appear and the bodily movement of mandible is arose.

Lifting Technique of Composite Bucket Foundation for Offshore Wind Turbines

2020 ◽  
Author(s):  
Hongyan Ding ◽  
Zuntao Feng ◽  
Puyang Zhang ◽  
Conghuan Le
Keyword(s):  
Finite Element ◽  
Prestressed Concrete ◽  
Large Scale ◽  
Element Model ◽  
Offshore Wind ◽  
Force Transmission ◽  
Element Analysis ◽  
Bucket Foundation ◽  
Transition Section ◽  
Section Structure

Abstract The onshore pre-fabrication technology for composite bucket foundations takes “prefabrication-assembly-lifting” as the core concept. The practice of pre-fabrication of upper and lower structures is prefabricated respectively. In the research of hoisting engineering technology, combined with the structural form and construction requirements of composite bucket foundation, the assembly scheme of the upper prestressed concrete transition section and the lower steel bucket and the hoisting scheme of integral foundation with compartments were designed. The finite element model in the lifting process of composite bucket foundation was established by the large-scale general finite element analysis software ABAQUS. For the optimization analysis of the lifting point arrangement during hoisting process, the number, position and arrangement form of lifting points are simulated and analyzed. The results show that the maximum value of the principal stress of the concrete transition section structure appears in the assembly stage with the lower steel bucket, and the structure checking calculation should be carried out as the most unfavorable lifting condition in construction; the peak point of structural stress is at the junction of girder and secondary beams and inner ring beams of concrete roof, which belongs to the weak position of force transmission. In construction, it should be paid attention to as the key part of monitoring to ensure composite bucket foundation is under reasonable stress and the stability in the lifting process. The research results can provide guidance and reference for the future batch production and standardization production construction for composite bucket foundations.

Three-Dimensional Reconstruction of Three Real Roots Included Periodontal Ligament and Implant Study

2014 ◽  
Vol 575 ◽  
pp. 931-934
Author(s):  
Qi Wang ◽  
Ling Chen ◽  
Zhong Zhang ◽  
Xing Hua Niu
Keyword(s):  
Finite Element ◽  
Periodontal Ligament ◽  
Three Dimensional ◽  
Element Model ◽  
Imaging Method ◽  
Element Analysis ◽  
Cross Sectional ◽  
The Real ◽  
Engineering Software ◽  
Ct Data

To investigate the periodontal ligament contains the real root of the three model cases, a combination of different implant and tooth variation of the stress distribution for the subsequent three root implant biomechanics analysis provides digital models. Methods: Mimics and Geomagic reverse engineering software for digital imaging method to obtain CT data processing. And the use of UG assembled in ANSYS workbench in finite element analysis. Results: A consistent with the real situation of three tooth root finite element model which contains periodontal ligament, and found that with the dental implant junction with the cross-sectional area decreases, where the stress amplitude fluctuations increases.

КОНСТРУКТИВНО-ТЕХНОЛОГІЧНІ ОСОБЛИВОСТІ ХВОСТО-ВИХ БАЛОК СІТЧАСТОГО ТИПУ З ПОЛІМЕРНИХ КОМПО-ЗИЦІЙНИХ МАТЕРІАЛІВ ВЕРТОЛЬОТІВ ТРАНСПОРТНОЇ КАТЕГОРІЇ

2020 ◽  
pp. 15-30
Author(s):  
А. Г. Гребеников ◽  
И. В. Малков ◽  
В. А. Урбанович ◽  
Н. И. Москаленко ◽  
Д. С. Колодийчик
Keyword(s):  
Finite Element ◽  
Strain State ◽  
Layer Structure ◽  
Metal Structure ◽  
Element Model ◽  
Stress Strain ◽  
Element Analysis ◽  
Mesh Structure ◽  
Stress Strain State ◽  
Mesh Structures

The analysis of the design and technological features of the tail boom (ТB) of a helicopter made of polymer composite materials (PCM) is carried out.Three structural and technological concepts are distinguished - semi-monocoque (reinforced metal structure), monocoque (three-layer structure) and mesh-type structure. The high weight and economic efficiency of mesh structures is shown, which allows them to be used in aerospace engineering. The physicomechanical characteristics of the network structures are estimated and their uniqueness is shown. The use of mesh structures can reduce the weight of the product by a factor of two or more.The stress-strain state (SSS) of the proposed tail boom design is determined. The analysis of methods for calculating the characteristics of the total SSS of conical mesh shells is carried out. The design of the tail boom is presented, the design diagram of the tail boom of the transport category rotorcraft is developed. A finite element model was created using the Siemens NX 7.5 system. The calculation of the stress-strain state (SSS) of the HC of the helicopter was carried out on the basis of the developed structural scheme using the Advanced Simulation module of the Siemens NX 7.5 system. The main zones of probable fatigue failure of tail booms are determined. Finite Element Analysis (FEA) provides a theoretical basis for design decisions.Shown is the effect of the type of technological process selected for the production of the tail boom on the strength of the HB structure. The stability of the characteristics of the PCM tail boom largely depends on the extent to which its design is suitable for the use of mechanized and automated production processes.A method for the manufacture of a helicopter tail boom from PCM by the automated winding method is proposed. A variant of computer modeling of the tail boom of a mesh structure made of PCM is shown.The automated winding technology can be recommended for implementation in the design of the composite tail boom of the Mi-2 and Mi-8 helicopters.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Finite Element Analysis of Tire/Rim Interface Forces Under Braking and Cornering Loads

1992 ◽  
Vol 20 (2) ◽  
pp. 83-105 ◽  
Author(s):  
J. P. Jeusette ◽  
M. Theves
Keyword(s):  
Finite Element ◽  
Shear Stress ◽  
Contact Pressure ◽  
Element Model ◽  
Shear Stresses ◽  
Detailed Knowledge ◽  
Stress Distributions ◽  
Element Analysis ◽  
Plane Shear ◽  
Normal Contact

Abstract During vehicle braking and cornering, the tire's footprint region may see high normal contact pressures and in-plane shear stresses. The corresponding resultant forces and moments are transferred to the wheel. The optimal design of the tire bead area and the wheel requires a detailed knowledge of the contact pressure and shear stress distributions at the tire/rim interface. In this study, the forces and moments obtained from the simulation of a vehicle in stationary braking/cornering conditions are applied to a quasi-static braking/cornering tire finite element model. Detailed contact pressure and shear stress distributions at the tire/rim interface are computed for heavy braking and cornering maneuvers.

Redrawing Operation a Star Shape from Cylindrical Shape Using Experimental and FE Analysis

2020 ◽  
Vol 38 (1A) ◽  
pp. 25-32
Author(s):  
Waleed Kh. Jawad ◽  
Ali T. Ikal
Keyword(s):  
Finite Element ◽  
Effective Strain ◽  
Element Model ◽  
Cylindrical Shape ◽  
Element Analysis ◽  
Punch Force ◽  
Maximum Value ◽  
Element Simulation ◽  
Blank Sheet ◽  
The Finite Element Model

The aim of this paper is to design and fabricate a star die and a cylindrical die to produce a star shape by redrawing the cylindrical shape and comparing it to the conventional method of producing a star cup drawn from the circular blank sheet using experimental (EXP) and finite element simulation (FES). The redrawing and drawing process was done to produce a star cup with the dimension of (41.5 × 34.69mm), and (30 mm). The finite element model is performed via mechanical APDL ANSYS18.0 to modulate the redrawing and drawing operation. The results of finite element analysis were compared with the experimental results and it is found that the maximum punch force (39.12KN) recorded with the production of a star shape drawn from the circular blank sheet when comparing the punch force (32.33 KN) recorded when redrawing the cylindrical shape into a star shape. This is due to the exposure of the cup produced drawn from the blank to the highest tensile stress. The highest value of the effective stress (709MPa) and effective strain (0.751) recorded with the star shape drawn from a circular blank sheet. The maximum value of lamination (8.707%) is recorded at the cup curling (the concave area) with the first method compared to the maximum value of lamination (5.822%) recorded at the cup curling (the concave area) with the second method because of this exposure to the highest concentration of stresses. The best distribution of thickness, strains, and stresses when producing a star shape by

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

scholarly journals Development of Simulation Based p-Multipliers for Laterally Loaded Pile Groups in Granular Soil Using 3D Nonlinear Finite Element Model

2020 ◽  
Vol 11 (1) ◽  
pp. 26
Author(s):  
Muhammad Bilal Adeel ◽  
Muhammad Asad Jan ◽  
Muhammad Aaqib ◽  
Duhee Park
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Design Guidelines ◽  
American Petroleum Institute ◽  
Winkler Foundation ◽  
Group Effect ◽  
Pile Groups ◽  
Element Analysis ◽  
Laterally Loaded Pile ◽  
Laterally Loaded

The behavior of laterally loaded pile groups is usually accessed by beam-on-nonlinear-Winkler-foundation (BNWF) approach employing various forms of empirically derived p-y curves and p-multipliers. Averaged p-multiplier for a particular pile group is termed as the group effect parameter. In practice, the p-y curve presented by the American Petroleum Institute (API) is most often utilized for piles in granular soils, although its shortcomings are recognized. In this study, we performed 3D finite element analysis to develop p-multipliers and group effect parameters for 3 × 3 to 5 × 5 vertically squared pile groups. The effect of the ratio of spacing to pile diameter (S/D), number of group piles, varying friction angle (φ), and pile fixity conditions on p-multipliers and group effect parameters are evaluated and quantified. Based on the simulation outcomes, a new functional form to calculate p-multipliers is proposed for pile groups. Extensive comparisons with the experimental measurements reveal that the calculated p-multipliers and group effect parameters are within the recorded range. Comparisons with two design guidelines which do not account for the pile fixity condition demonstrate that they overestimate the p-multipliers for fixed-head condition.

Finite Element Analysis of the Distributed Vibration Absorbers for Structural Noise Control

2005 ◽  
Author(s):  
Ashwini Gautam ◽  
Chris Fuller ◽  
James Carneal
Keyword(s):  
Finite Element ◽  
Numerical Model ◽  
Base Plate ◽  
Element Model ◽  
Fe Model ◽  
Vibration Absorbers ◽  
Element Analysis ◽  
Poroelastic Media ◽  
Hexahedral Elements ◽  
Component Models

This work presents an extensive analysis of the properties of distributed vibration absorbers (DVAs) and their effectiveness in controlling the sound radiation from the base structure. The DVA acts as a distributed mass absorber consisting of a thin metal sheet covering a layer of acoustic foam (porous media) that behaves like a distributed spring-mass-damper system. To assess the effectiveness of these DVAs in controlling the vibration of the base structures (plate) a detailed finite elements model has been developed for the DVA and base plate structure. The foam was modeled as a poroelastic media using 8 node hexahedral elements. The structural (plate) domain was modeled using 16 degree of freedom plate elements. Each of the finite element models have been validated by comparing the numerical results with the available analytical and experimental results. These component models were combined to model the DVA. Preliminary experiments conducted on the DVAs have shown an excellent agreement between the results obtained from the numerical model of the DVA and from the experiments. The component models and the DVA model were then combined into a larger FE model comprised of a base plate with the DVA treatment on its surface. The results from the simulation of this numerical model have shown that there has been a significant reduction in the vibration levels of the base plate due to DVA treatment on it. It has been shown from this work that the inclusion of the DVAs on the base plate reduces their vibration response and therefore the radiated noise. Moreover, the detailed development of the finite element model for the foam has provided us with the capability to analyze the physics behind the behavior of the distributed vibration absorbers (DVAs) and to develop more optimized designs for the same.

Sign in / Sign up

Export Citation Format

Share Document